IPEMA Playground PSL021 User manual

PSL021 6-foot Freestanding Slide Instructions
1 Playground Drive
Greenfield, IN 46140
1-800-667-0097
Colors depicted in photos
may not match your order.

PARTS LIST
3.5-inch Post
Deck for
Freestanding Slide
QTY: 2
QTY: 1
Part #1
Part #2
6-foot Stair for
Freestanding
Slide
6-foot Handrail for
Freestanding Slide
QTY: 1
QTY: 2
Part #3
Part #4
Slide End
Mount
Wave Slide Middle
Support
QTY: 1
QTY: 1
Part #5
Part #6
Single Slide Metal
Barrier
6-foot Wave Slide
QTY: 2
QTY: 1
Part #7
Part #8

Single Slide
Hood
3.5-inch Flat
Clamp
QTY: 1
QTY: 2
Part #9
Part #10
3.5-inch Tube
Clamp
QTY: 2
QTY:
Part #11
Part #12

STEP 1
Install posts according to the General
Information Guide. After installing
the posts, using one (1) M10*35 bolt,
two (2) M10 washers, and one (1)
M10 lock nut, attach the deck to the
pre-attached deck clamp, as shown
in the image. Repeat this process for
the other deck clamp.
STEP 2
Connect half of the 3.5-inch tube
clamp to the guardrail using one (1)
M8*30 bolt. Set the guardrail into
place, then attach the second half of
the clamp using the hardware
provided in the clamp bag.

STEP 3
Using two (2) M10*25 bolts, four (4)
M10 washers, and two (2) M10 lock
nuts, connect the guardrail to the
deck. Repeat steps 2 and 3 for the
other guardrail.
STEP 4
Using two (2) M10*25 bolts, four (4),
and two (2) lock nuts, connect the
handrail to the guardrail as shown.
Set the bottom end of the handrail
into footing. Information for digging
footers can be found in the General
Installation Guide.

STEP 5
Using one (1) M10*25 bolt, two (2)
M10 washers, and one (1) M10 lock
nut, attach the top of the stairway to
the deck on the opposite side of the
posts. Repeat this step for remaining
attachment points.
STEP 8
Using one (1) M10*25 bolt, two (2)
M10 washers, and one (1) lock nut,
attach one stair handrail bracket to
the proper stair connection point.
Repeat this process for the remaining
connection points.

STEP 7
Using two (2) M10*25 bolts, four (4)
M10 washers, and two (2) M10 lock
nuts, connect the bottom of the
handrail to the stair.
STEP 8
Take one (1) 3.5-inch flat clamp, and
loosely attach it around a post using
the bolts and nuts provided in the
clamp hardware bag. Repeat this
process on the other post. Then, use
one (1) M8*40 bolt, one (1) M8
washer, and one (1) M8 lock nut to
attach each side of the slide hood to
each clamp. Leave bolts loose until
slide is in place.

STEP 9
Using two (2) M8*20, two (M8)
spring gaskets, and two (2) M8
washers, attach the slide to the slide
end mount.
STEP 10
Using two (2) M8*20 bolts, two (2)
M8 lock nuts, and four (4) M8
washers, attach the middle slide
support to the bracket under the
slide.

STEP 11
Using one (1) M10*45 bolt, two (2)
M10 washers, and two (2) M10 lock
nuts, attach one side of the slide to
the deck. Repeat the process for the
other side of the slide.
STEP 12
Using one (1) M8*45 bolt, one (1) M8
washer, one (1) M12 washer, and one
(1) M12 Inner hex spiral nut, attach
the slide to one side of the slide hood.
Repeat this process for the other side
of the slide. Make sure all bolts are
properly tightened.