IQ IQLT1 UNIVERSAL TILT User manual

Component Checklist
Bits Bag
IQLT1 37”- 64” UNIVERSAL TILT WALL MOUNT
Important Notes
TOOLS REQUIRED
• Power Drill
• 6mm or 10mm Drill Bit
• Phillips Head Screwdriver
• 13mm (1/2”) Socket Wrench
or Shifter
• The Universal Tilt Wall Mount supports LCD and plasma flat panel displays from 37” to 64” and
supports a maximum load of 200 lbs (91 kg). The adjustable tilt allows a -5° to +15° viewing angle.
• This product is compatible with VESA mounting centres from 500mm to 816mm wide.
• Please do not begin installation until you have thoroughly read and understood these instructions.
The manufacturer does not accept responsibility for incorrect installation.
Mounting Screws
M8x16mm / M8x45mm (x4 each)
M6x16mm / M6x45mm (x4 each)
M5x16mm / M5x45mm (x4 each)
M4x16mm / M4x45mm (x4 each)
Cross Recess Screws
Installation Instructions
1-Left Monitor Bracket (CC)
1-Right Security Bracket
1-Left Security Bracket
1-Right Monitor Bracket (BB) Flange Screw (x4) Washer (x4)Masonary Wall
Plug (x4)
Multi-Washer (x4) 19 x 8 x 19.4
Spacer (x4)
12.7 x 6 x 12.7
Spacer (x4)
Timber Stud Wall
Mounting the Wall Plate
Masonry Wall
Wall Plate
OR
Masonry
Wall Plug
10mm (3/8”) Hole 6mm (1/4”) Hole
Wall Plate
Flange Screw
Flange Screw
Washer Wall Plate
Washer
It is recommended when mounting directly into masonary wall,
that the mounting holes are positioned as far apart as possible,
and ensure not to drill directly into mortar.
TIP: Use the bubble level to ensure the wall plate is horizontal.
TIP: Use the bubble level to ensure the wall plate is horizontal.
Use a stud finder to precisely locate the timber stud and ensure
that the mounting holes are located in the centre of the stud.
It is recommended that the mounting holes are positioned as
far apart as possible.
Note: Ensure the Wall Plate is mounted
with the folded tabs pointing upwards.
Note: Ensure the Wall Plate is mounted
with the folded tabs pointing upwards.

B
Back
of Display
Security
Bracket (Right)
Tension Knob
Security Bracket
(Right)
Top of
Display
CC
BB
Bracket
Spacer
Note: For demonstration purposes, the wall
has been omitted from the above images.
Note: For demonstration purposes, the wall
has been omitted from the above images. D-2
Back Plate
Padlock
Shackle
5mm (3/16”)
diameter
or less
With the Brackets attached
to the display, lift the
display and hook the
brackets onto the Wall
Plate as shown.
D-1
Lock in the desired tilt
angle by tightening the
tension knob. Like a
ratchet, the tension
knob can be pulled out
and away from the
bracket and turned
independently to
reposition the
knob (see below).
For added security, it is suggested that the left and right Security
Brackets be inserted. Additionally, a padlock can be used
through each Security Bracket and the Wall Plate to securely
prevent the display from being removed from the Wall Plate,
depending on your installation needs (padlocks not included).
Note: This procedure will
require two persons.
NOTE: When attaching the mounting
screws to the display, make sure
the direction of the brackets is right
and ensure that both brackets are
vertically aligned. Recessed Mounting Holes: If the
mounting holes are recessed into
the back of the display, use the
supplied spacers to pack the
recessed hole. If the mounting
screw is M4, M5, or M6, use the
12.7 x 6 x 12.7mm spacers. If the
mounting screw is M8, use the
19 x 8 x 19.4 spacers. Ensure
that the brackets are securely fixed
to the display.
Mounting the Display Brackets
CAttaching the Display to the Wall Plate
DQ-Lock Locking Tilt and Security
Mounting
Screw
Mounting
Screw
Mounting Screw
Multi Washer
Multi
Washer
Multi
Washer
Recessed Hole
M6 & M8
Screw Hole
M4 & M5
Screw Hole
LOOSEN TIGHTEN
Padlock
Holes