Ironton 53578 User manual

SAVE THESE INSTRUCTIONS
2-Pack Indoor Simulated Dome
Security Cameras
Owner’s Manual
WARNING: Read carefully and understand all ASSEMBLY AND OPERATION
INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
precautions may result in serious personal injury.
Item #53578

Page 2 of 10
Thank you very much for choosing an Ironton™product!
For future reference, please complete the owner’s record below:
Serial Number/Lot Date Code: ________________________________
Purchase Date: ____________________________________________
Save the receipt, warranty, and this manual. It is important that you read
the entire manual to become familiar with this product before you begin
using it.
This 2-Pack Indoor Simulated Dome Security Cameras is designed for
certain applications only. Northern Tool and Equipment is not
responsible for issues arising from modification or improper use of this
product such as an application for which it was not designed. We
strongly recommend that this product not be modified and/or used for
any application other than that for which it was designed.
For technical questions, please call 1-800-222-5381.

Page 3 of 10
Table of Contents
Intended Use..........................................................................................................................................4
Technical Specifications......................................................................................................................4
Important Safety Information...............................................................................................................4
Mounting Instructions ..........................................................................................................................6
Maintenance ..........................................................................................................................................7
Parts Diagram........................................................................................................................................7
Parts List................................................................................................................................................8
Replacement Parts................................................................................................................................8
Limited Warranty...................................................................................................................................9

Page 4 of 10
Intended Use
Ironton’s 2-Pack Indoor Simulated Dome Security Cameras provide the appearance of a working
overhead security camera, making it a suitable deterrent for your home or business. The camera
operates continuously, with a red blinking LED light. These cameras are intended for indoor use only.
Technical Specifications
Property
Specification
Camera/dome rotation
360°L/R rotation
Camera angle
Fixed 45 angle
Camera lens diameter
0.25 inch
Camera base diameter
3 ¾ inches
Power source
3AA size batteries (not included)
Important Safety Information
⚠WARNING
Read and understand all instructions. Failure to follow all instructions may result in serious injury
or property damage.
The warnings, cautions, and instructions in this manual cannot cover all possible conditions or
situations that could occur. Exercise common sense and caution when using these cameras.
Always be aware of the environment and ensure that the cameras are used in a safe and
responsible manner.
Do not allow persons to operate or assemble the products until they have read this manual and
have developed a thorough understanding of how they work.
Do not modify the cameras in any way. Unauthorized modification may impair the function and/or
safety and could affect the life of the products. There are specific applications for which the
products were designed.
Use the right tool for the job. DO NOT attempt to force small equipment to do the work of larger
industrial equipment. There are certain applications for which the equipment was designed. They
will do the job better and more safely at the capacity for which they were intended. DO NOT use
the equipment for a purpose for which it was not intended.
Industrial or commercial applications must follow OSHA requirements.
⚠WARNING
These products may contain chemicals known to the State of California to cause cancer, birth
defects or other reproductive harm.
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to the State of California to cause cancer, birth defects, or other
reproductive harm. Some examples of these chemicals are:
- lead from lead-based paints,
- crystalline silica from bricks and cement and other masonry products, and

Page 5 of 10
- arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well-ventilated area, and work with approved
safety equipment, such as dust masks that are specially designed to filter out microscopic
particles.
Handling power cords on corded products may expose you to lead, a chemical known to the State
of California to cause cancer and birth defects or other reproductive harm. Wash your hands after
handling.
⚠WARNING
WORK AREA SAFETY
Inspect the work area before each use. Keep work area clean, dry, free of clutter, and well-lit.
Cluttered, wet, or dark work areas can result in injury. Using the cameras in confined work areas
may put you dangerously close to cutting tools and rotating parts.
Do not use the cameras where there is a risk of causing a fire or an explosion; e.g., in the
presence of flammable liquids, gases, or dust. These products can create sparks, which may
ignite the flammable liquids, gases, or dust.
Do not allow the cameras to come into contact with an electrical source. These tools are not
insulated and contact will cause electrical shock.
Keep children and bystanders away from the work area while operating the cameras. Do not allow
children to handle them.
Be aware of all power lines, electrical circuits, water pipes, and other mechanical hazards in your
work area. Some of these hazards may be hidden from your view and may cause personal injury
and/or property damage if contacted.
⚠WARNING
PERSONAL SAFETY
Stay alert, watch what you are doing, and use common sense when operating the cameras. Do
not use them while you are tired or under the influence of drugs, alcohol, or medication. A moment
of inattention while operating them may result in serious personal injury.
Dress properly. Do not wear loose clothing, dangling objects, or jewelry. Keep your hair, clothing
and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving
parts. Air vents on the cameras often cover moving parts and should be avoided.
Wear the proper personal protective equipment when necessary. Use ANSI Z87.1 compliant safety
goggles (not safety glasses) with side shields, or when needed, a face shield. Use a dust mask in
dusty work conditions. Also use non-skid safety shoes, hardhat, gloves, dust collection systems,
and hearing protection when appropriate. This applies to all persons in the work area.
Do not overreach. Keep proper footing and balance at all times.
Secure the work with clamps or a vise instead of your hand when practical. This safety precaution
allows for proper tool operation using both hands.

Page 6 of 10
⚠CAUTION
CAMERA USE AND CARE
Do not force the cameras. Products are safer and do a better job when used in the manner for
which they are designed. Plan your work, and use the correct products for the job.
Check for damaged parts before each use. Carefully check that the cameras will operate properly
and perform intended functions. Replace damaged or worn parts immediately. Never operate the
cameras with damaged parts.
Do not use cameras with malfunctioning switches. Any power tool that cannot be controlled with
the power switch is dangerous and must be repaired by an authorized service representative
before using.
Store the cameras when not in use. Store in a dry, secure place out of the reach of children.
Inspect the cameras for good working condition prior to storage and before re-use.
Use only accessories that are recommended by the manufacturer for use with your cameras.
Accessories that may be suitable for one product may create a risk of injury when used with
another tool. Never use an accessory that has a lower operating speed or operating pressure than
the tool itself.
Keep guards in place and in working order. Never operate the products without the guards in
place.
Mounting Instructions
⚠WARNING
Do not use in wet locations.
Intended for indoor use only.
Select a location for the decoy camera that is easily visible by potential intruders, but out of reach.
Point decoy camera and LED towards the area of concern so that the flashing light is easily
visible.
Select the position for the camera and drill holes for the anchors using the paper template
provided. (Screws and anchors are supplied. Use an appropriate screw type for the mounting
surface.)
Install batteries according to "+ /- polarity marker". Insert the two AA batteries into the battery
compartment.
Do not tighten screws completely so you can attach the camera base through the keyhole slots.
Fit camera body keyhole slots to the screws. Slide camera onto screws and rotate camera to lock
into keyhole slots.
Note: If camera is loose, adjust depth of screws until camera fits snugly.
Position camera front with flashing LED so that it is easily visible.

Page 7 of 10
Maintenance
Maintain the solar decoy camera by adopting a program of conscientious repair and maintenance in
accordance with the following recommended procedures. It is recommended that the general
condition of any tool be examined before it is used. Keep your tool in good repair and clean.
Inspect
Hardware should be checked for looseness. Tighten as required.
Frames should be inspected for wear or damage
Parts Diagram

Page 8 of 10
Parts List
Part Number
Description
Quantity
1
cover
1
2
bottom cover
1
3
battery cover
1
4
red LED light
1
Replacement Parts
For replacement parts and technical questions, please call Customer Service at 1-800-222-5381.
Not all product components are available for replacement. The illustrations provided are a
convenient reference to the location and position of parts in the assembly sequence.
When ordering parts, the following information will be required: item description, item model
number, item serial number/item lot date code, and the replacement part reference number.
The distributor reserves the rights to make design changes and or improvements to product lines
and manuals without notice.

Page 9 of 10
Limited Warranty
Northern Tool and Equipment Company, Inc. ("We'' or '"Us'') warrants to the original purchaser only
("You'' or “Your”) that the Ironton product purchased will be free from material defects in both
materials and workmanship, normal wear and tear excepted, for a period of one year from date of
purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in
accordance with product instructions. There are no other warranties, express or implied, including the
warranty of merchantability or fitness for a particular purpose. If the product does not comply with this
limited warranty, Your sole and exclusive remedy is that We will, at our sole option and within a
commercially reasonable time, either replace the product or product component without charge to You
or refund the purchase price (less shipping). This limited warranty is not transferable.
Limitations on the Warranty
This limited warranty does not cover: (a) normal wear and tear; (b) damage through abuse, neglect,
misuse, or as a result of any accident or in any other manner; (c) damage from misapplication,
overloading, or improper installation; (d) improper maintenance and repair; and (e) product alteration
in any manner by anyone other than Us, with the sole exception of alterations made pursuant to
product instructions and in a workmanlike manner.
Obligations of Purchaser
You must retain Your product purchase receipt to verify date of purchase and that You are the original
purchaser. To make a warranty claim, contact Us at 1-800-222-5381, identify the product by make
and model number, and follow the claim instructions that will be provided. The product and the
purchase receipt must be provided to Us in order to process Your warranty claim. Any returned
product that is replaced or refunded by Us becomes our property. You will be responsible for return
shipping costs or costs related to Your return visit to a retail store.
Remedy Limits
Product replacement or a refund of the purchase price is Your sole remedy under this limited warranty
or any other warranty related to the product. We shall not be liable for: service or labor charges or
damage to Your property incurred in removing or replacing the product; any damages, including,
without limitation, damages to tangible personal property or personal injury, related to Your improper
use, installation, or maintenance of the product or product component; or any indirect, incidental or
consequential damages of any kind for any reason.
Assumption of Risk
You acknowledge and agree that any use of the product for any purpose other than the specified
use(s) stated in the product instructions is at Your own risk.
Governing Law
This limited warranty gives You specific legal rights, and You also may have other rights which vary
from state to state. Some states do not allow limitations or exclusions on implied warranties or
incidental or consequential damages, so the above limitations may not apply to You. This limited
warranty is governed by the laws of the State of Minnesota, without regard to rules pertaining to
conflicts of law. The state courts located in Dakota County, Minnesota shall have exclusive jurisdiction
for any disputes relating to this warranty.

Page 10 of 10
Distributed by:
Northern Tool & Equipment Company, Inc.
Burnsville, Minnesota 55306
www.northerntool.com
Made in China