IST I1000M User manual

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
I1000M
Operation Manual

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
Table of Contents
TOPIC Page
Cover 1
Table of Contents 2
Safety 3
FCC 3
Introduction 5
Systemoverview 6
Operationcontrols 7
Dockingstation 7
K1/K2buttons 7
Volumeup/downbuttons 7
Audioon/offbutton 7
Up/down & left/right buttons 7
Privacy 7
Listenbutton 7
Talkbutton 7
Unlockthedoor 7
Remotecontrol 7
Master Settings
Clock 8
Registerallstations 8
Assigning numbers to room, patio & door stations 8
Changing numbers at the room station 9
Assigning names to room stations 9
Selecting the door chime 9
Doorvolume 10
Master display brightness 10
Settingprivacyatthemaster 10
Mode 11
Setting the mode for the master, room or patio 11
AM/FMRadio 11
Settingradiopresets 12
Changinginputsources 12
Switching between AM and FM radio 12
Settrebleandbass 13
Autoon 13
Autooff 13
Room and patio operation 14-15
Source 16
Set 16
Privacy 16
Backlight 16
Talk 16
DoorTalk 16
Hands free listening 17
Unlock door from master and room 17
Remote Control 17 – 18
Troubleshooting 19
Warranty 20
Pa
g
e 2 of 19

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
The Lightning flash with arrowhead symbol within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of
sufficient ma
g
nitude to constitute a risk of electric shock to
p
ersons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of instructions in the literature
accompanying the product.
Important safety instructions: The apparatus should not be exposed to dripping and
splashing and that no objects with liquids, such as vases. Shall be placed with the apparatus.
Remark: The terminal marked with is used as earthing terminal. It must be
connected to the protective earthing of mains and maintained in use.
Important Safety Instructions
Please read all instructions carefully before installing the I1000 series music communication
system.
All components of the I1000 Series music communication system are permanent connection,
and must be installed and disassembled by a qualified installer. Install in accordance with the
manufacturer’s instructions. And installation must conform to all local building and electrical
codes.
Warning;
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that product heat.
9. Only use attachments/accessories specified by the manufacturer.
10. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
Pa
g
e 3 of 20

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions; (1) this devise may not cause harmful interference, and (2) this device must accept
ant interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the users authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment on and off, the user is encouraged to try to correct the interference by one or more of
the following measures;
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that which the receiver is
connected.
Consult with the dealer or an experienced radio technician for help.
Pa
g
e 4 of 20

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
Master Station
INTRODUCTION
The I1000M is a Music and Intercom system that integrates with today’s portable music players,
with a modern look that compliments any décor. It’s a multi sourced system which allows you to
select between three music sources. You can listen to your own home entertainment through the
auxiliary input throughout your home. The I1000M not only allows you to use your portable hand
held players throughout your home, but offers you the comfort and convenience of
communication and room monitoring as well. With features like Automatic Selective Call and a
full function remote control, it is convenient to use and offers exceptional value.
2 3
5
4
6
1
9 7
8
1. Integrated docking station for hand held music players
2. Speaker
3. K1 button
4. Audio on/off button
5. Volume up/down buttons
6. Listen and talk buttons
7. Left/right and up/down arrow buttons
8. K2 button
9. LCD display
Pa
g
e 5 of 20

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
System Overview
I1000M Music Communications System is made up of 5 components.
Master unit
Room stations
Patio stations
Door stations
Auxiliary input wall plate (maximum one per system)
Master Unit
The I1000M Master unit allows control of the music and intercom functions. It enables you to set
the system music and intercom volume levels, bass and treble levels for the radio, clock settings,
privacy settings and more. The integrated docking station allows you to play any portable music
source at the master. External 30 watt 8 ohm ceiling and in-wall speakers (optional equipment)
can be connected directly off the master station for improved sound quality. The master allows
you to play music from the radio, local line source (3.5mm jack) and the auxiliary input wall plate.
Room Station
The I1000R room station is designed for indoor use. It will provide intercom, radio and input for
any portable music source. You can communicate and monitor other stations including the master.
Door communications can also be answered from room stations as well as the master and patio.
External 30 watt 8 ohm ceiling and in-wall speakers (optional equipment) can be connected
directly off any room station for improved sound quality. The room station allows you to play
music from the radio, it’s local line source (3.5mm jack) and the auxiliary input wall plate.
Patio Station
The I1000P outside station is weather resistant. It is designed to require only minimal protection
from the weather. The patio station can provide intercom communication and radio music. The
system door chime will sound at the patio station so guests will not be missed.
Door Station
The I1000D door station is designed to require only minimal protection from the weather. It will
allow communication with the master, room and patio stations and verify who is there before
opening the door. With the optional door release mechanism, the door can be unlocked from any
room of the home that has a room station installed.
Auxiliary Input Wall Plate
The AUXWP wall plate allows the input of most any music sources into the system and broadcast
music to any room or patio that has a system station. This source can be a CD changer, portable
music device or optional radio device.
Note: There can only be one Auxiliary Input Unit installed per system.
Pa
g
e 6 of 20

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
Operation Controls
Integrated Docking Station
Located on the left side of the master, behind the plastic door. Plug any hand help music device into master
docking station by using a 3.5mm plug from the hand held device. The hand held device can also be charged by
plugging it into the USB or firewire port provided in the docking station. Most hand held devices will fit inside the
docking compartment along with all the cables. Select
LOCL source and the hand held device will play through the
master unit.
Note: With the changing technology, we can not guarantee all handheld music players will charge in the USB or
firewire port.
K1/K2 Buttons
The K1/K2 buttons are located just to the right of the LCD display on the master. These keys are multi-functional
that are used in conjunction with the LCD display. This allows programming of names, setting time and many
more functions.
Volume Up/Down Buttons
The up/down volume buttons control the volume of the master unit.
Audio On/Off Button
The audio on/off feature is used to conveniently turn the system music ON or OFF at all units simultaneously. This
does not affect the intercom function.
Up/Down and Left/Right Buttons
These buttons are designed for multi functions such as the following features;
Up/Down Buttons
Scrolling the menu content
Changing the AM/FM tuner presets
Changing characters
Left/Right Buttons
Moving the display cursor
Changing the radio frequency
Privacy
The privacy feature will prevent the station from being monitored. This feature is to ensure privacy at the location.
Listen Button
The listen button is used for hands free operation for the receiving side of the call. By pressing and holding the
listen button the hands free operation will activate.
Talk Button
The talk button is used to communicate with room, patio and door stations. Door communication will only be
heard at the door station that rang. After the talk button is pressed (this is an all broadcast) and once the
responding station has pressed their talk button within 25 seconds, the selective call feature is activated. This
means all stations not on this call will return to the music they were listen to before the first call.
Unlock the Door
The unlock door feature allows you to unlock any door from the master or room unit. Only the door you are in
communication with, will be unlocked. This optional feature is only available when installed.
Remote Control
The remote control can perform many features including activation of the talk and listen functions. And you can
selectively call a room or patio by using the station number or unlock the door when this feature is installed.
Pa
g
e 7 of 20

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
MASTER SETTINGS
ENTER
PREV
*12H PM 04:10
SET TIME
K1
K2
PROG
PREV
ROOM
REGISTRY
Clock
To set press K1 for
MENU
Use the up/down arrow buttons to scroll through the menu until SYSTEM is displayed
Press
PROG K2 and use up/down arrow buttons until SET CLOCK is displayed and press K2 PROG
The * will be next to the 12H or 24H, use the up/down arrow buttons to select 12 or 24 hour clock
Press the left/right arrow buttons to set the * next to the AM or PM mark, use the up/down arrow buttons to select AM or PM
Press the left/right arrow buttons to set the * next to the hours, use the up/down buttons to set the hours to the correct time
Press the left/right arrow buttons to set the * next to the minutes, use the up/down buttons to set the minutes to the correct time
Press K2
ENTER to exit clock setup
K1
K2
Register All Stations
Before you can take advantage of all the features that the I1000M offers, you will need to register all units.
Press K1 for
MENU
Scroll through the system using the up/down arrow buttons and select
PROG with K2
Scroll the registry using the up/down arrow buttons and select
PROG with K2
Select the stations you would like to register using the up/down arrow buttons and pressing K2 for
ENTER. For example
You can select to register all the room stations by selecting
REG ROOM
After pressing K2,
ENTER the system will automatically count the available room stations connected to the system
Repeat these steps for the patio and door stations
ENTER
PREV
0001
ROOM 3396 No.
K1
K2
Assigning numbers to Room, Patio and Door Stations (at the master)
Press K1 button and scroll the menu using the up/down arrow buttons. Select
ROOM UNIT and press ENTER K2
Scroll the up/down arrow button until you reach the station you want to assign a number to. Press the K2 button
PROG .
The I1000M will automatically assign a number to the room unit. You can change this number by selecting
PROG K2.
The display will indicate
SET NO . Select PROG by pressing K2.
Use the up/down arrow buttons and the left/right arrow buttons to assign the number of your choice.
Press
ENTER button K2
Repeat these steps for all room, patio and door stations
This process is more easily done at each individual station, see Changing Numbers at the Room Stations
Pa
g
e 8 of 20

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
ENTER
PREV
0001
ROOM 3396 NO.
K1
K2
Changing Numbers at the Room Stations
At the master, press K1
MENU
Scroll the up/down arrow buttons to SYSTEM, press K2 PROG
Scroll the up/down arrow buttons to
EN.SET NO , press K2 PROG
Scroll to
ON , press K2 to ENTER
This gives room stations authority to change room station numbers
At the room station, press and hold SET button for 5 seconds, the default station no should appear with the last digit blinking
Using the VOLUME up/down buttons, select the number for this digit
Using the SOURCE button select another digit and again using the VOLUME up/down buttons select the number for this digit
Once the new station number has been selected, press the SET button to memorize this number in the system.
Repeat these steps for all room and patio stations
Once this feature is on you can now change the room or patio stations from the individual locations.
The master station number will always default to 0.
ENTER
PREV
JOHN ROOM
ROOM 0002 NAME
K1
K2
Assigning Names to Room Stations
Press K1 for
MENU
Scroll to ROOM UNIT using the up/down arrow buttons and select PROG with the K2 button
Select the room by using the up/down arrow buttons and select
PROG with the K2 button
Scroll to
SET NAME using the up/down arrow buttons and select PROG with the K2 button
Use the up/down arrow buttons to change the characters and the left/right buttons to move to the left or right
Once the name of the room station has been completed, select
ENTER by pressing the K2 button
Repeat these steps for each room, patio and door station.
There are a maximum of 8 characters available.
ENTER
PREV
MELODY 01
RING TONE
K1
K2
Pa
g
e 9 of 20
Selecting Door Chime
Press K1 for
MENU
Scroll using the up/down arrow buttons to
DOOR UNIT and select PROG using the K2 button
Using the UP/down arrow buttons scroll to the door station and select
PROG with the K2 button
Using the up/down arrow buttons scroll to
SET RING and select PROG using the k2 Button
Using the up/down arrow buttons choose the ring tone and select
ENTER with the K2 button

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
ENTER
PREV
30
SPEAKER VOL
K1
K2
Door Volume
Press K1 for
MENU
Scroll to
DOOR UNIT option using the up/down arrow buttons, select PROG with theK2 button
Using the up/down arrow buttons scroll to the door station and select
PROG with the K2 button
Using the up/down arrow buttons scroll to
SET VOL and select PROG with the K2 button
Using the up/down arrow buttons change the volume level to the desired volume and select
ENTER with the K2 button
Note: This will only change the intercom volume at the door station
ENTER
PREV
* OFF
BRIGHTNESS
K1
K2
Master Display Brightness
Press K1 button for
MENU
Scroll to
MASTER using the up/down arrow buttons and select PROG with the K2 button
Using the up/down arrow buttons scroll to
BRIGHTNESS and select PROG with the K2 button
Using the up/down arrow buttons choose between
OFF , LOW or HIGH brightness
Select
ENTER with the K2 button
ENTER
PREV
* ON
SET PRIVACY
K1
K2
Setting Privacy at Master
Press the K1 button for
MENU
Scroll to
MASTER option using the up/down arrow buttons and select PROG with the K2 button
Using the up/down arrow buttons scroll to
SET PRIVACY and select PROG with the K2 button
Using the up/down arrow buttons scroll between
ON or OFF and select choice by pressing ENTER with the K2 button
Selecting
ON will enable the privacy mode at the master only.
Pa
g
e 10 of 20

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
MODE
The mode will tell the master, room or patio what functions to activate. There are six (6) mode settings that may be
chosen. Normal mode is considered the standard setup.
1. Normal – Intercom with music
2. Intercom Only – Intercom only with no music
3. Music Only – Music only with no intercom
4. Monitor – Monitor with no music or intercom
5. Monitor (OR) – Monitor override gives the ability to talk into a monitored room
6. Off – This turns off all modes
ENTER
PREV
* NORMAL
MASTER MODE
K1
K2
Setting the mode for Master, Room or Patio
Press K1 button for
MENU
Scroll to MASTER using the up/down arrow buttons and select PROG with the K2 button
Using the up/down arrow buttons scroll to
SET MODE and select PROG with the K2 button
Using the up/down arrow buttons scroll the mode settings and select
ENTER with the K2 button for your choice
Repeat these steps choosing
ROOM or PATIO to select different modes at individual room and or patio stations.
SAVE
AM
FM 92.5MHz
PM 03:30:50 V25
K1
K2
AM/FM Radio
Selecting a radio station at the master
Manual Scan
Press left/right arrow buttons for scanning manually
Auto Scan
Press left/right arrow buttons and hold for two (2) seconds for auto scanning
Pa
g
e 11 of 20

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
ENTER
EXIT
PRESET NO 01
CHANNEL STORING
K1
K2
Setting Radio Presets
Press left/right arrow buttons until the desired station has been reached
Press K2 to
SAVE this station
Select the preset number with the up/down arrow buttons and select
ENTER with the K2 button
SOURCE
AM
FM 92.5 MHz
PM 03:30:50 VOL25
K1
K2
Changing Input Sources
Press the K2 button for
SOURCE
This will display the next available source in the lower right corner of the display
Press the K2 button to select the next available source and repeat until the source desired is displayed on the lower left
side of the display
AUX
AM
FM 92.5 MHz
PM 03:30:50 VOL 25
K1
K2
Switching Between AM and FM Radio
Press K2 for
SOURCE
This will display the next available frequency (
AM or FM ) in the top right corner of the display
Press the K1 button to select the next available frequency
Pa
g
e 12 of 20

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
ENTER
PREV
+ 01
SET BASS
K1
K2
Set Bass and Treble
Press K1 Button for
MENU
Scroll to the
SYSTEM using the up/down arrow buttons and select PROG with the K2 button
Using the up/down arrow buttons scroll to
RADIO TONE and select PROG with the K2 button
Using the up/down arrow buttons scroll to
SET BASS and select PROG with the K2 button
Using the up/down arrow buttons change the bass level and select
ENTER with the K2 button
Repeat these steps choosing
SET TREBLE to change the treble level
ENTER
PREV
ON AM 06:30
AUTO ON
K1
K2
Auto On
To set the auto on, press K1
MENU
Press the up/down arrow buttons until
SYSTEM appears and press K2 PROG
Press the up/down arrow buttons until AUTO appears and press K2 to PROG
Press the up/down arrow buttons until AUTO ON appears and press K2 PROG
Using the left/right and up/down arrow buttons, set the desired time you want the system to come on
When the correct on time is set press K2 to
ENTER this time
Scroll the up/down arrow buttons until
Auto On appears
ENTER
PREV
* ON AM 07:30
AUTO OFF
K1
K2
AUTO OFF
To set the auto off function, start from the last step in Auto On section above
Press K2 for
ENTER
Using the left/right and up/down arrow buttons, set the desired time you want the system to turn off
When the correct off time is set, press K2 to ENTER this time
Pa
g
e 13 of 20

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
Room Station
1
2
3
4
6 7 5
8
1. Speaker
2. LCD display
3. Listen button
4. Talk button
5. Volume up and down buttons
6. Source selection button
7. Set and door release button
8. 3.5mm local music input jack (on bottom of station)
Pa
g
e 14 of 20

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
Remote Control
2
6
5
4
3
1
7
8
9
10
11
12
13
14
16
15
1. Door release button
2. Mute button
3. Line in (source)
4. Local input select
5. AM radio select
6. FM radio select
7. Volume up
8. Listen button
9. Talk button
10. Monitor
11. Volume down
12. Radio preset select
13. Privacy
14. Station number select 0-9
15. Patio
16. Clear
Pa
g
e 15 of 20

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
ROOM AND PATIO OPERATION
SOURCE
This enables you to change the source for each room separately. There are RADIO, LINE IN and LOCL to choose
between.
Radio – AM/FM radio is distributed from the master
Line In – Line in is distributed from the Auxiliary Input Unit (AUXWP)
LOCL – Local input is distributed from the 3.5mm jack located on the bottom of all room and patio
stations.
SET
The set button is a multi-function button that can be used to change radio stations to turning on the privacy
feature.
Change Radio Stations
Make sure the source is set to AM/FM radio
Press the set button once to display the current radio station
Press the set button again until radio station is flashing. The flashing will last for five seconds
Use the volume up/down buttons to change radio stations
Press and hold the volume up/down buttons to auto scan radio stations
Change AM/FM
Press the set button once to display radio station
Press the set button twice to display AM/FM flashing. The flashing will last for five seconds
Use the Volume up/down to toggle between AM/FM
Scan Preset Radio Stations
Press the set button once to display the radio station
Press the set button once to display preset until flashing. The flashing will last for five seconds
Use the volume up/down buttons to scan preset radio stations
Privacy
Press and hold the set button for two seconds
Privacy will flash in the left corner of the display
Use the volume up/down buttons to toggle between on/off
Press the set button
Press the source button
Backlight
Press and hold the set button for two seconds
Privacy will flash in the left corner of the display
Press the set button again until the backlight begins to flash
Use the volume up/down buttons to toggle between HIGH, LOW or OFF
Press the set button
Press the source button
Talk
Press the talk button and hold to activate the intercom
Speak into the speaker in a normal voice and hold the talk button until finished
Once the intercom call has been answered (within 25 seconds) the system will automatically go
into a select call mode (a private conversation between the two rooms) All other rooms will return
to the music they were playing before the intercom was activated
Door Talk
Press the talk button to answer the door. Once you release the talk button it will activate the door
Pa
g
e 16 of 20

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
Hands Free Listening
Press and hold the listen button to activate the hands free operation. By holding the
listen button the second party does not need to press their talk button.
Hold the listen button until the conversation has ended
Unlock Door From Master (Optional feature)
Once the door chime has been activated, UNLOCK DOOR will be on display
Press the K1 button to unlock the door. It is recommended for safety reasons that
you verify who is at the door before using the UNLOCK feature.
The door will lock automatically. The delay of the auto door locking will depend on
the delay setting programmed in the door release unit, (I1000DR). Contact your
installer for more information.
Unlock Door From Room Station (optional Feature)
Once the door chime has been activated the UNLOCK DOOR button (same as SET
button) may be used. For safety reasons it is recommended that the you verify who is
at the door before using the UNLOCK feature.
Press the UNLOCK DOOR button momentarily
The door will automatically lock. The delay of the auto door locking will depend on
the delay setting programmed in the door release unit, (I1000DR). Contact your
installer for more information.
Remote Control
Talk Button
Point the remote at the master, room or patio station. Then press the talk button on
the remote to initiate an intercom call to all other stations.
Press the talk button again to end.
Once the call has been answered (within 25 seconds) the call will automatically go
into the select call mode. All other stations not on this call will go back to the music
they were listening to before the call was initiated.
Selective Call
Point the remote at the master or room station then press the number of the station
you want to call and press the talk button to initiate the call. Press talk again when
finished talking.
Once the call has been answered the private communication will be active for 25
seconds.
To talk to the patio press the patio button, then the patio station number button and
then the talk button on the remote. Always end by pressing the talk button when
through talking.
Door Talk
Once the door bell has rung, press talk on the remote to activate the door talk and
press talk again to activate door listen.
Press the listen button to cancel this communication
All Listen
Point the remote at the room station then press the listen button for the all listen
feature.
The listen feature will be active until you press the listen button again.
If the patio speaker is desired, press the patio button and then the patio station
number on the remote and then the listen button. Press listen again when finished.
Pa
g
e 17 o
f
20

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
Remote Control (continued)
Monitor
Point the remote at the room station then press the monitor button for all monitor
or select a room station by pressing the number of the room station and then
monitor.
Press the monitor button again to cancel room monitoring.
If the patio station is desired, press the patio button and then the patio station
number on the remote and then press the listen button. Press the listen again
when finished.
Privacy
Point the remote at the room station, master or patio and press the privacy
button.
Press the privacy button again to cancel the privacy mode.
Radio Presets
Point the remote at the room station, master or patio and press the preset button
+ or – to change the preset radio stations.
Clear
Point the remote at the room station, master or patio and press the clear button
to clear the room number selected
Music Volume Up/Down
Point the remote at the room station, master or patio and press either the button
volume + to raise the music volume or the button volume – to lower the music
volume.
Intercom Volume
Point the remote at the master or room station and press the listen button. Then
press the button volume + to raise the intercom volume or the button volume –
to lower the intercom button. When finished setting the intercom volume press
the listen button again and the room station will return to the pre-selected music.
Source
Point the remote at the room station and press either the FM, AM, Line In or
Local buttons to select the source.
Mute
Point the remote at the room station and press the mute button to activate the
mute feature.
Press the mute button a second time to cancel the mute function
Unlock the Door
Once the door bell has been rung, point the remote at the room station. For
safety reasons it is recommended that you verify who is at the door before
unlocking the door. To unlock the door simply press the unlock button on the
remote.
Pa
g
e 18 of 20

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
Trouble Shooting Tips and Questions
Problem or Question
Solution
Can not hear music at room stations Volume controls operate independently. Make sure to adjust the
volume for each source
Check to see if the mode setting at the master is set for intercom only
or monitor/off
Can not hear room intercom Volume controls operate independently. Make sure to adjust the
intercom volume for each station
Check to see if the mode settings at the master are set to music only
or monitor/off
Volume controls operate independently. Make sure to adjust the
volume for each room station and source.
Where do I put my hand held music player at
the room station? A hand held music player bracket is sold separately. Contact your installer or Intrasonic Technolo
gy
for more information
Can I char
g
e my hand held music player? Only at the master can you charge a hand held music player. This is
done via the USB or firewire port in the docking station. Note some
p
la
y
ers ma
y
not char
g
e throu
g
h these
p
orts.
Can not hear the room station bein
g
monitored Volume controls operate independently. Make sure to adjust the
intercom volume for each station
Make sure
p
rivac
y
control is not active
Where do I plug in my hand held music player at
the room station? At every room and patio station, on the bottom, there is a 3.5mm jack.
Simply plug a 3.5mm cable (supplied with Master) into the jack and
plug the other end of this cable into the headphone jack on your music
de
vi
ce
Can not hear my hand held music player Make sure you have LOCL (local) selected as the music source at the
station you are attempting to connect your hand held device.
Volume controls operate independently. Make sure to adjust the
volume for each music source at the station.
How do I monitor a baby’s room? Using the remote control or master, select to room number you wish
to monitor and then press monitor. See “MONITOR” under remote
control section.
Us
in
g
t
h
e
r
e
m
ote,
p
r
ess
m
o
ni
to
r
o
r
se
l
ect
r
oo
m n
u
m
be
r
What happens if the power
g
oes off? Like most electronic devices, when the power is off the equipment will
not operate. The I1000M has a battery backup that should keep the
owner selected settin
g
s durin
g
most
p
ower outa
g
es.
Where is the battery backup and how do I
replace it? The battery backup is located behind the master front panel. Simply
loosen the three screws on the bottom of the master face plate and
pull the face plate off. In the upper right hand corner there is a square
cover with a single screw. Remove this screw and remove the battery
behind it. Watch the battery polarity and put the new battery in using
the same direction as the old battery. The battery number for
replacement is CR2032. After replacement remount the master face
plate and tighten the 3 screws on the bottom.
I cannot hear my MP3 player or other music
source that is plugged into the master docking
station throughout the home
There is a local and broadcast switch in master. To distribute music
throughout the entire system move the switch into the broadcast
position.
Pa
g
e 19 of 20

IntraSonic Technology, Inc. | 610 Presidential Drive Ste 104 | Richardson, Texas 75081 |
877.435.0670
www.intrasonictechnology.com
Intrasonic Technology, Inc. 2 Year Limited Warranty
Intrasonic Technology warrants its products to be free of manufacturing defects for two years
from the date of closing or actual installation. This warranty only applies to products purchased
from authorized dealers or distributors. If proof of installation can not be supplied, the
manufacturing date code may be substituted. The warranty extends to the original user or
subsequent owner of the product during the warranty term. Intrasonic Technology will replace or
repair the product at it’s option at no charge with a rebuilt or new product. All products with
manufacturing defects must be returned to Intrasonic Technology.
If an Intrasonic Technology product is determined to have a manufacturing defect, please call our
toll free number (877-435-0670) before any attempt to dismantle or repair the product. Any
attempt to dismantle or repair product will void the warranty.
An RMA (Return Material Authorization) will be required prior to returning a product to Intrasonic
Technology. To obtain an RMA number, call our toll free number (877-435-0670) and speak with
a customer service representative. All products returned to Intrasonic Technology without an RMA
will be refused.
The limited warranty is in lieu of any other warranties, expressed or implied and any other
obligations or liability on the seller’s part. The limited warranty does not cover service calls,
damage caused by improper installation, acts of God or violation of building or electrical codes.
Intrasonic Technology will not be liable for consequential, incidental or other damage arising in
connection with use or inability to use this product. In no event shall Intrasonic Technology’s
liability hereunder exceed the cost of the product covered hereby. No person is authorized to
assume for Intrasonic Technology or obligate Intrasonic Technology for any other liability in
connection with the sale of this product. Some states do not allow the exclusion or limitation of
consequential, incidental damage, so the above limitation or exclusion may not apply. This limited
warranty gives you specific legal rights and you may also have other rights, which may vary state
to state.
Pa
g
e 20 of 20