ITC Elio VersiControl Configuration guide

230 E. Lakewood Blvd. • P.O. Box 8338 • Holland • MI • 49422-8338
Phone: [phone] • Fax: [phone] • www.itc-us.com • [email protected] • 03/08/17
VersiControl RGB Zone Control Install Instructions
(Part #’s: 21050-XX, 21060-XX, 21053-XX & 21056-XX)
Safety Instructions
• Disconnect power before installing, adding or changing any component.
• To avoid a hazard to children, account for all parts and destroy all packing materials.
• Do not install any luminaire assembly closer than 6” from any combustible materials.
For warranty information please visit www.itc-us.com
1. INSTALL: Determine the installation location for your controller. Make sure to consider the size of the controller
(4.8”L x 2.9”W x 1.2”H) when determining your location. Note, it will require room for access and for wiring.
Once determined the controller can either be screwed in place or attached with double stick tape.
• If using double stick tape rst clean the back of the module and the install location with alcohol wipes (not
provided). Place the double stick pads (not provided)on the back of the module as shown below. Remove
the paper and stick the module in place.
• If screwing the controller in place use the four 5x15mm stainless steel Phillips pan head screws provided.
2. WIRING DIAGRAM: Follow the wiring diagram below to wire the module to your system.
PARTS / TOOLS NEEDED:
RGB Zone Controller RGB Lighting
(Varies) Mounting Screws x 4 Butt Splices
(not provided)
Double Stick Tape -
Optional (not provided)
Alcohol Wipes
(not provided)
Double
Stick Tape
4.8”
2.9”
12” 4.8” 13” 1.2”
1.6”
2.9”
1.2”
2”
1.2”
12” 4.8” 13” 1.2”
1.6”
2.9”
1.2”
2”
Controller
Black - 12-24V DC IN (-)
Red - 12-24V DC IN (+)
(Max 16A)
Inputs
Outputs
(+) Red/White
(-) Red
(-) Green
(-) Blue
Zone 1 - (Max 16A)
Single Zone - 21060-XX

230 E. Lakewood Blvd. • P.O. Box 8338 • Holland • MI • 49422-8338
Phone: [phone] • Fax: [phone] • www.itc-us.com • [email protected] • 03/08/17
Controller
Black - 12-24V DC IN (-)
Red - 12-24V DC IN (+)
(Max 20A)
Inputs
Outputs
(+) Red/White
(-) Red
(-) Green
(-) Blue
Zone 1 - (Max 8A)
(+) Red/White
(-) Red
(-) Green
(-) Blue
Zone 2 - (Max 8A)
(+) Red/White
(-) Red
(-) Green
(-) Blue
Zone 3A*
(+) Red/White
(-) Red
(-) Green
(-) Blue
Zone 3B*
Four Zone - 21050-XX or 21056-XX
*Zone 3A + Zone 3B = Max 8A
Select The Color Select The Speed of the Color Fade
• Push the knob once • Push the knob a third time
• Turn right or left to select the desired color • Turn right to speed up, or left to slow down
Select The Brightness Turn Off System
• Push the knob a second time • Push and hold knob for three seconds
• Turn right to increase brightness, left to decrease brightness Turn On System
• Push & hold knob for one second
Controller
Black - 12-24V DC IN (-)
Red - 12-24V DC IN (+)
(Max 20A)
Inputs
Outputs
(+) Red/White
(-) Red
(-) Green
(-) Blue
Zone 1 - (Max 8A)
(+) Red/White
Zone 2 - (Max 8A)
(+) Red/White
Zone 3A*
(+) Red/White
Zone 3B*
Four Zone Simplied Wiring- 21053-XX
*Zone 3A + Zone 3B = Max 8A
3. OPERATION: You are now ready to customize your lighting. Follow the operating instructions below or scan
the QR code to watch a short video.