ITC TS-0695 User manual

HD Color Video Camera
TS-0695
User Manual
Please Read This Manual Before Operation

2
Precautions
Safety Tips
Please read this manual carefully before use the Camera.
To avoid damage from stress, violent vibration, soaking during transportation, storage and installation.
Take care of each components of Camera during installation, and install camera at where is affordable
enough, to avoid drop or scratches of camera case.
Do not apply excessive voltage. (Use only the specified voltage.) Otherwise, you may get an electric shock
or a fire may occur.
Keep the transmission of RS-485, Video signal away from powerful electromagnetic radiation resources.
Do not shoot images that are extremely bright (e.g., light sources, the sun, etc.) for long periods of time. Do
not use or store the camera in the specified extreme conditions. (Please refer to specification sheet of
camera.)
Do not clean camera with active chemical or corrosive detergents, and remove dust or dirt on the surface of
the lens with a blower (Commercially available)
Do not disassemble any camera components, in case of abnormal operation, contact your authorized dealer
or the store where you purchased the product.
After long time operation, these components may get machine wear like Motor, slip ring, you can contact for
repair or change, the local dealer or the shop where you bought this camera.
Supplied Accessories
HD Color Video Camera (1)
12V/2.0A DC Power adaptor (1)
Installation bracket (1) Installation screw (1)
USB3.0 data lines (3m),serial control line,RS-232C to RS-485 cable
IR Remote Controller (1)
User’s Manual (1)

Main Features
Camera and Lens
Video CMOS Sensor: 1/2.8" Type Exmor CMOS 3.27 Megapixel
Image: 16:9 3.27 pixel
Video Signal:
60Hz mode, camera output 1080p30 as default, support 1080p@30/25/20/15/10/5, 720p, 800x600,
640x480/60/50/30/25/20/15/10/5;
50Hz mode, camera output 1080p@25 as default, support 1080p@25/20/15/10/5, 720p, 800x600,
640x480/50/25/20/15/10/5;
Lens zoom: 20 Optical x 12 digital zoom, f=4.7-90mm F1.6-3.5
Wide angle lens: 55.4 degree
Minimum Illumination: 0.1Lux
White Balance: Auto/Sunlight/Cloudiness/Shade/fluorescence white balance
Focus: Auto/Manual
Iris: Auto/Manual
Shutter Speed: 1/1 - 1/10,000S
Black light compensation: On/Off

3
Pan/Tilt Movement
Pan Movement: 0-355°
Tilt Rotation: Up: 45°, Down: 45°
Built in Pan/Tilt Motor: Pan Speed: 1-200°/Second Tilt speed: 1-150°/Second
Preset Speed: Pan running: 120°/sec Tilt running: 100°/sec
Preset: 64 preset position, 4 Patrol lines
Rear board connectors
High Definition Interface: HDMI, HD-SDI, DVI, CVBS, YPbPr
Controller Signal Interface: 8 leads mini DIN (VISCA IN, VISCA OUT/RS485)
Controller Signal Interface: Dip-switch Pin 7/TTL Signal;
Baud Ratio: 9600/ 38400 bps
Power supply interface: DC 12V 2A
Electrical Index
Power supply adapter: 12V DC/2A
Input voltage: 12V DC(10.5-14V DC)
Input power: 24W(MAX)
Structure
Material: All-alloy, PC plastic
Dimension (Width x highness x depth) :
154x250x140mm / 330x210x230mm (NET/PACKAGE)
Working environment: Indoor
Temperature: -0℃to +45℃
Storage temperature: -10℃to +60℃
Color: Silver Gray

4
Rear Board & function
1. Front View
1) Lens
Adopted 10x optical auto focus lens
2) IR Receiver
To receive IR mote controller signal LED
3) Power LED
LED Blinking when power plug in, Blue color Led
4) Stand by LED
LED blinking while shut down camera use remote controller, and Orange color
5) IR Receiver
To receive IR mote controller signal LED
2. Dip-switch Settings
1) Dip-switch 1(Set Communication baud rate)
ON=>38400bps, OFF=>9600bps
(Please set the baud rate before turn on power. Baud rate setting failed if turn off power.)
2) Dip-Switch 2(Set Control protocol)
ON: RS-485 &PELCO-D (ON=RS485&Pelco-D)
OFF: RS-232C&VISCA (OFF=RS232C &VISCA )
3) Dip-Switch 3 (Set as Upgrading)
Set dip switch 3 as ON, then you can do upgrading of the camera, Must Set OFF as usual working.
4) Dip-Switch 4& 5 (Set address code)
When you used RS232C &VISCA to control multi-cameras, suggest to set address code as OFF;

5
When you used RS-485 &PELCO-D to control multi-cameras, suggest to refer to below Camera address code
setting
table;
5) Switch 6 (Set IR signal output switch)
When set as ON, it will receive the signal from remote control and VISCA IN to control this device, if set it to
OFF means close signal output.
Camera address code setting
Dip-switch4Dip-switch 5
1 OFF OFF
1 OFF ON
2 ON OFF
3 ON ON
Cable Connection info
VISCA RS-232C IN Reference
VISCA Out Reference
Pin S/N Function
1DTR IN
2DSR IN
3TXD IN
4GND
5RXD IN
6GND
7
IR Commander Signal
OUTPUT
8NO Connection
Pin S/N Function
1DTR OUT
2DSR OUT
3TXD OUT
4GND
5RXD OUT
6GND
7RS-485－
8RS-485＋

6
Camera to PC connection
Camera Cascade
OSD Menu
Access OSD menu to understand the features of camera and change the settings.
Note: Camera can’t move pan/tilt when OSD menu is displaying on screen.
Self-testing OSD Menu
There are OSD menu as following when camera start on, and it will be
disappear after self-testing completed.
Following is the parameter of camera, and different camera module adopted
display different OSD menu parameters.
ADDRESS (Camera address))
BUADRATE (Camera baud rate)
PROTOCOL (PTZ Control Protocol)
CONTROL (Camera control type)
LENSTYPE (Camera module adopted)
DOMETYPE (Camera model No.)
VENDOR (Manufacturer name)
VERSION (Initial Factory version)
Dome OSD
Press “DOME OSD” button on remote controller to
display:
1) Pin
Chose OSD menu
Move by ↑or ↓key
2) Parameters
Chose by ↑or ↓key
3) Values
Display OSD parameters, chose by ←or →to change the
parameters value of menu OSD
ADDRESS
BUADRATE
PROTOCOL
CONTROL
LENSTYPE
DOMETYPE
VENDER
VERSION
1
9600
VISCA
RS-232C
ACUTE
2.3.4.4
INFORMATION
&PAN SPEED
TILT SPEED
SCAN SPEED
TOUR PATH
TOUR DWELL
PROPORTION
AUTO REV
FRAME
20
20
6
1
5
ON
P
60HZ
1
2
3

7
Menu Parameters:
PAN SPEED Default value: 30
Adjustable pan movement speed scope 1~63
TILT SPEED Default value: 30
Adjustable tile movement speed scope 1~63
SCAN SPEED Default value: 6
Adjustable pan movement speed scope 1~63
TOUR PATH Default value: 1
Optional tour path at 1~4
TOUR DWELL(Tour duration time) Default value: 5
Tour duration is 1~60 seconds
PROPORTION (Speed matching) Default value: ON
ON means enable speed match function, OFF means not.
AUTO REV Default value: P
Image auto flip(positive)/N(upside down)/OFF
FRAME Default value: 60HZ
Support 60Hz & 50Hz for optional
Note:
60Hz mode, camera output 1080p30 as default, support 1080p@30/25/20/15/10/5, 720p, 800x600,
640x480/60/50/30/25/20/15/10/5;
50Hz mode, camera output 1080p@25 as default, support 1080p@25/20/15/10/5, 720p, 800x600,
640x480/50/25/20/15/10/5;
LENS OSD
Access LENS OSD from remote controller, there is OSD menu display on screen and its possible to adjust
or change any settings of lens OSD. (Up/down direction key to change the menu, left/right direction key to
change the parameters value)
DISPLAY Default value: OFF
SUPPORT ON/OFF
SHARPNESS Default value: NORMAL
LOW/HIGH
SATURATION Default value: NORMAL
LOW/HIGH
NR (Noise Reduction) Default value: 3
Adjustable Value 0~5
WB (White Balance) Default value: Auto
AUTO/MANUAL/OUTDOOR/INDOOR/ONE PUSH/ATW
R GAIN (RED RAIN) Default value: 206

8
Adjustable scope: 0~255
B GAIN (Blue Gain) Default value: 150
Adjustable scope 0~255
AE (Auto Exposure) Default value: Auto
AUTO/MANUAL/SHUTTER/IRIS/BRIGHT
SHUTTER SPEED Default value: 1/1
Shutter speed range: 1/1—1/10000
IRIS Default value: Close
Close/F1.4-F22
BRIGHT Default value: 0
0 ~ 31
IR Remote Controller
1. Reset:
Restart Camera and restore to factory default settings
2. Camera Selection
Select Camera of IR 1,2,3
3. Preset positions
1-9: preset positions
Set: Setting preset position
Clear: Clear preset position
Call: Call preset position
Note: if you need set number 1 preset position, you
should press Number key “1”, then press “Set” to
setting
this position;
4. Zoom in/out Control Zone
+: Zoom in
-: Zoom out
5. Pan/tilt Control
: move up
: move down
: move left
: move right
: auto Pan moving
6. Additional Function zone
Freeze: image freeze
BL: Backlight compensation
WB: White Balance
AE: Auto Exposure
D zoom: Digital Zoom
HDMI: swap to HDMI Video output
DVI: Swap to DVI video output
Format: swap between different format
7. Power supply Switch
Switch of stand by and working status
8. OSD Menu Zone
Dome OSD: enter Camera OSD Menu
Lens OSD: enter Lens OSD Menu
9. Slow Zoom in/out Zone
+: Zoom in slowly
-: Zoom out slowly
10.Focus Control Zone
Auto: auto focus of lens
Manual: manual focus of lens
Far: focus at far distance objects
Near: focus at near distance objects
11. Pan/Tilt Function Zone

9
L-Limit: Set Left limit Scanning position
Scan: Enable Boundary scanning
R-Limit: Set Right limit scanning position
Home: Camera Home position
Tour: Enable Patrolling
Rev: Image auto-flip
Remote controller Function Summary
S/
NRegional Keynote functions
1 Reset Restart Camera and back to
default Factory settings.
2
Camera ID
Chose
Chose camera according to
your Remote control
3
Preset
position
function area
Chose serial no. of preset
position
To “Set” as preset position
To “Clear” preset position
To “Call” preset position
4Fast-speed
Zoom in/out
Zoom in of camera Lens
Zoom out of camera lens
5Pan/Tilt
control
Move camera up-side
Move camera down-side
Move camera go left
Move camera go right
Enable Pan movement
scanning
6 Auxiliary
Image Freeze
Backlight compensation
White Balance
Auto Exposure
Digital Zoom

10
Swift as HDMI Video output
(not available with this
camera)
Swift as DVI Video output
(not available with this
camera)
Swipe different video formats
(not available with this
camera)
7 Power on/off Power-on/off
8 OSD Menu
Login DOME OSD Menu
Login Lens OSD Menu
9Slow speed
Zoom in/out
Zoom in slowly speed
Zoom out slowly speed
10 Lens Focus
adjustments
Auto focus automatically
Manual focus
Lens zoom in far end
Lens zoom in Near end
11
Pan & Tilt
Function area
Set Left points for boundary
scanning
Enable Scanning
automatically
Set Right limit point for
Boundary scanning
Home position of Camera
Enable Touring
Image Up-side down option

11
Operation instruction
Joy-stick PTZ Keybaord operation
To use joy-stick PTZ keyboard to control Camera including, pan/tilt/zoom movement, set Tour scanning, enable
boundary scanning, etc.
option function
turn up Down-side movement
turn down Up-side movement
turn left Left movement
turn right Right movement
Rotate left Zoom in
Rotate right Zoom out
Special Preset positions function
Preset position
No. Functions
76 Enable stand-by status
77 To display Self-testing menu on screen
90 Image up-side down
91 Login system OSD Menu
92 Set Left limit position of scanning
93 Set right limit position of scanning
94 Restart Camera and return default settings
95 Call Lens OSD Menu of Lens
96 Home position
97 Enable regional Pan scanning
98 Enable Tour scanning
99 Enable 360 degree Horizontal scanning
Amcap Software application
Open the CD-ROM AMCAP v3.0.9.exe software, choose Devices->USB video equipment (or
similar options), then chose “preview”, as shown in the diagram below, you can preview image.
.
Before Preview Video output, please check Capture-> ;

12
Adjust different video format
60Hz mode, camera output 1080p30 as default, support 1080p@30/25/20/15/10/5, 720p, 800x600,
640x480/60/50/30/25/20/15/10/5;
50Hz mode, camera output 1080p@25 as default, support 1080p@25/20/15/10/5, 720p, 800x600,
640x480/50/25/20/15/10/5;
The Camera upgrade (control)
Install the HD Camera Debugger Tool in your PC while connected VISCA IN of Camera to RS232 at PC,
please refer to follow Steps:
a) Connected Camera (VISCA IN) to PC (RS-232) with RS232 Cable which provided along with Camera in the
Package;
b) Select Baud rate, Protocol, Port info match with your Camera dip-switch settings, default settings is 9600,
VISCA, 1
c) Try to control Pan, Tilt, Zoom while settings completed, to make sure camera is connected properly.
d) Dome Upgrading-> import the file-> chose correct firmware of camera->Click “Start” to proceeding
upgrading…
e) It said “upgrading process successfully ” after upgrading completed, then camera will RESET automatically
to initial settings;
f) Need to upgrade camera’s software, choose the upgrade via IMPORT THE FILE, and click START begin
the upgrade, when complete the upgrade, the camera restart.

13
Specification sheet
Model No. TS-0695
Image
Sensor
Image Sensor 1/2.8" Type Exmor CMOS
Effective Pix 3.27 Megapixel
Min. Illumination 0.5Lux
White balance Auto/Manual
Gain control Auto/Manual
B/L compensation On/Off
Shutter speed 1/1 - 1/10,000S
S/N ratio >50db
Lens
Focus f=4.7-90mm F1.6-3.5
Iris Auto/Manual
Lens 20 Optical x 12 digital zoom
Horizontal view angle 55.4
Video output HDMI, HD-SDI, DVI, CVBS, YPbPr Video output
Signal system YUY2 | 1920x108030p, 1280x 720 30p
Control terminal EIA/RS232C,EIA/RS485(Bidirectional)
Control Protocol VISCA,PELCO-D
baud rate 9600/38400bps
patrol line 4 cruise sequence
preset position 64 preset positions
Speed Match Pan/Tilt movement speed depends on camera module
zoom in/out
OSD Menu
Access to OSD Menu and adjust camera module
parameters
Image auto flp Support Horizontal/Vertical image flip
Pan movement speed 1-200°/Second
Tilt movement speed 1-150°/Second
Pan movement range Pan: 0-355°
Tilt movement range Up: 90°, Down: 45°
Pan scanning automatically Support Pan scanning automatically
Boundary scanning 0-355°(programmable)
Remote controller IR Wireless Remote controller P/T/Z
Power supply DC12V,2A
Work Temperature 0-50℃
Humidity 0-95%RH
LxWxH 250mm x 140mm x 154mm
Weight 1380g

14
Installation instruction
Desktop Installation
Put the camera on the desk flat, and make sure the camera in level. If wan to put the camera on oblique surface, please make
sure the angle of inclination less than 15 degree for ensure camera pal and tilt working in normal operation.
Tripod Installation
Twist the tripod’s screw on the camera tripod hole, then the tripod could be installed on the bottom of camera.
The tripod screw must fit below specifications:
Note:
Tripod must stand on a flat surface.
The screws and cap which used for tripod must not be used for a higher position, such as ceiling mount.
Ceiling Mount
Step 1: Fixed the quadrate
bracket onto ceiling
Quadrate
brackets
Ceiling
Use screws to fixed the
quadrate brackets onto
ceiling, four raised parts
face to ceiling.

15
Compatibility
As we tested with Amcap S/W, Skype, Microsoft Lync, VSEE, Vidyo, DEBUT Software, most of them are Video
Conferencing system application, and it works perfect;
Step 2: Fixed the
deltaic bracket.
Slotted screws
Use the screws to fix
the deltaic bracket with
the bottom plate of
camera.
Deltaic bracket
Step 3: Connect
the deltaic bracket
to quadrate
bracket.
Use hand prop the camera,
let the slotted screw nut
through the groove of
quadrate bracket.
Step 4: Lock the
screws.
Use the screws to lock the
quadrate and deltaic brackets
to finish the installation.
Lock screws

16
Troubleshooting
Before bringing in your camera for service, check the following as a guide to troubleshoot the problem. If the
problem cannot be corrected, consult with your Dealer.
Symptom Cause Remedy
The power of the
camera is not turned
on.
The supplied AC power adaptor is not
connected to the DC IN 12V jack firmly, or
the AC power cord is not inserted firmly
into the AC power adaptor or the AC
outlet.
Insert the power cord firmly as far as it
will go.
Not Turn On the Power switch as “ON”. Turn On the Power switch as “ON”.
Insufficient frame
rate detected
MJPEG1920X108030FPS
YUY21920X10809FPS
Make sure you Chose correct video
format.
Pan,tilt or zoom
cannot be operated.
Any menu is displayed on the monitor
screen.
Press the “Dome OSD” OR “Lens OSD”
on the Camera remote control Unit to
turn off the menu from the monitor
screen.
The panning or tilting range is limited
Pan/Tilt movement range is ± 45 degree.
The Remote
Commander does
not work.
The Camera Select button you pressed
on the Remote Commander does not
match the number set with the IRSELECT
switch on the camera.
Press the Camera Select button
corresponding to the IR SELECT
SWITCH setting on the Camera.
Used out of battery Change new battery (AA x 2)
The VISCA control is
not available with a
computer connected
to the camera.
The computer is not correctly connected
to the camera.
Make sure the connection between the
computer and camera is made correctly.
Check that the VISCA control setting
(RS-232C or RS-422) and the baud rate
setting (9600 bps or 38,400 bps) are
properly made with the BOTTOM switch
on the bottom of camera and the COM
Port which configured in your computer.
The camera cannot
be operated at all.
Pull out the plug of the power cord from
the AC outlet, then reinsert it into the AC
outlet after a while.