Iveco IVECONNECT User manual

I VECONNECT - P ROCEDURE FOR Software Update VIA USB PENDRIVE
1
/
4
IVECONNECT UPDATE PROCEDURE
Before updating the Iveconnect system, please ensure the vehicle is safely parked and in
key-off condition. During the update procedures, any battery disconnection or any USB
pendrive unexpected removal may compromise the operating condition of the system.
Iveconnect system can be updated follo ing a 2 steps procedures:
•Iveconnect System Update
•Iveconnect Applications Update
Note: the entire Iveconnect Update procedure ill take approaximately 20 min and System
Update (……Pack1.zip ) should be started first!!
Iveconnect System Update
The USB Pendrive used for the update has to be empty and formatted .
Do nload from the eb page here this file has been do nloaded, the files listed belo :
•XXXX_pack1.zip  contains iles or Iveconnect System Update
•XXXX_pack2.zip  contains iles or Iveconnect Applications Update.
The notation XXXX is used intentionally; these are numbers that identify the last soft are version available
for do nload on the eb page (i.e. for the Iveconnect System Update it could be 2412_pack1.zip) .
Uncompress the 3 files contained in the XXXX_pack1.zip and copy them in the root folder of the USB
Pen Drive, these 3 files are named as follo s:
1) ULDRMode_Popup.CAB
2) install.lst
3) flash.bin .
Please ensure all the above files are present in the USB Pendrive and follo the steps outlined belo to
start and complete the Iveconnect System Update:
A. S itch ON the Iveconnect system by pushing the po er-on button , confirm the Disclaimer
screen and ait until the home page appears (see Figure 1 - Home Page belo )
Figure 1- Home page
B. Plug the USB PenDrive containing the 3 files listed above into the Iveconnect USB connector located
on the upper shell of the vehicle ( see Figure 2).

I VECONNECT - P ROCEDURE FOR Software Update VIA USB PENDRIVE
2
/
4
Figure 2 - Location of the USB connector on the upper shell
C. Fe seconds after a arning message ill be displayed and then the Iveconnect system ill restart.
After restarting the update procedure ill start automatically.
D. During the update DO NOT REMOVE THE USB PENDRIVE. The image of a orker image ill be
sho n during the various phases of the update process. Three different screens sho ing “Verifying
Update Signature”, “Updating Image…” and “Verifying Update” ill be sho n together ith a
progress bar.
Figure 3 – Update in progress
E In case the update is completed successfully , the following image will appear
Figure 4 – Update Completed
F Now the update is almost complete, unplug the USB Pen Drive, press the button to switch off
the system then wait 5 sec and press it again to switch on the system
A further update screen will appear, please wait until the home screen appears by confirming the
Disclaimer screen
The System Update Procedure sets automatically English as default language of the Iveconnect; if the
language set in the Instrument cluster of the vehicle is different, Iveconnect once started ill ask to align
the Iveconnect language accordingly by sho ing a system restart pop-up.

I VECONNECT - P ROCEDURE FOR Software Update VIA USB PENDRIVE
3
/
4
Congratulations you have successfully completed the Iveconnect System Update .
IMPORTANT NOTE:
In case of issues during the update procedure read what reported below:
•Update not started In case the warning message is missing and/or the system is not restarted
at step C, hold down CD-EJECT button for 10sec, then release it
In this way a system restart is forced and the update procedure should start
•Failure during the update procedure In case the update fails, the display will show the
image below with the reason of the failure In this case, please, unplug the USB and hold down
the CD-EJECT button for 10 sec and restart the update procedure again
Figure 5 – Error during the Update procedure
If problem persists, please take note of the information reported and contact the Iveco service
network for additional support
Iveconnect Applications Update
The USB Pendrive to use for the Update procedure has to be empty and formatted. In case you ish to use
the same Pendrive previously used for the Iveconnect System Update, please ensure the 3 files previously
copied are deleted.
Uncompress the 4 files contained in the compressed archive XXXX_pack2.zip and copy them in
the root folder of the USB Pen Drive; these 4 files are named as follows:
1 “ANS app”
2 “DSE app”
3 “QC_MMI app”
4 “applications cfg”
Please ensure all 4 files are present then follo the steps outlined belo to start and complete the
Iveconnect Applications Update:
A With the Home screen displayed, insert the USB pen-drive on the USB connector on the upper
shell (see Figure 2)
B. Wait until the reboot notification indo s is displayed and ans er yes to the request to restart
the Iveconnect system. As soon as the system is restarted, the applications installation procedure
ill start and a screen similar to the one reported belo ill appear.

I VECONNECT - P ROCEDURE FOR Software Update VIA USB PENDRIVE
4
/
4
Figure 6 – Application Update procedure screen
C. During the progress of the Application update procedure various screens reporting a green
progress bar ill be displayed (see figure 7) .
Figure 7 – Application Installation Progress bar
D In case the Application Update procedure is completed successfully, the Disclaimer screen will
appear press confirm to access the Home Page Remove the USB pendrive and delete all files
previously copied to avoid unintentional updates
Congratulations the Iveconnect System has been updated completely !!!
IMPORTANT NOTE:
In case the progress bar gets red instead of green, this means the application update
procedure has failed. In this case, PLEASE REMOVE USB PENDRIVE, ait for the system
reboot and re-start the Application Update procedure from point A above (in case the
home page does not appear s itch-off the system by pressing the button , ait fe
seconds and press it again to s itch-on the system).
In case the Application Update procedure fails again, please contact the Iveco Service
Net ork for additional support.