Chase effects and master intensity channel layouts
The table below shows how the chase effects and master intensity controls are
mapped to DMX channels for the 24+E and 3+E modes. Mode DMX does not
use chase effects. The rst channel of the xture occurs at the DMX address
selected using ADDR and successive channels for the xture follow from there.
Control 24+E 3+E
C1 Effect Ch25 Ch4
C1 Speed Ch26 Ch5
C1 Xfade Ch27 Ch6
C2 Effect Ch28 Ch7
C2 Speed Ch29 Ch8
C2 Xfade Ch30 Ch9
Master intensity Ch31 Ch10
General notes
• Ensure that only one DMX device in
the chain is set as master (e.g. the
lighting desk). The xture is usually
set to slave mode
• The xture is shipped with the
DMX address set to 001.
• If the xture is used as a master,
DMX transmission will only occur
when the DMX address is displayed
(e.g. A001, A002, etc).
• The four digit display can be set to
fade out after 60 seconds, press
to resume. To alter this mode:
PERS > DISP.
Chase effects
This section describes each of the 31 internal chase
effects that are selectable either via the control menu
(PROG > C1/C2 > EFEC) or using DMX values sent
from an external source. To use the internal effects, set
the MODE option either to EF M (to control effects via
the menu) or 3+E or 24+E (to control effects externally
via DMX).
DMX EFEC Chase effect description
value value
0-7 00 Off
8-15 01 Rainbow chase down
16-23 02 Rainbow chase up
24-31 03 White single cell chase down
32-39 04 White single cell chase up
40-47 05 White single cell chase scatter
48-55 06 50/50 duty cycle strobe white
56-63 07 50/50 duty cycle strobe red
64-71 08 50/50 duty cycle strobe blue
72-79 09 50/50 duty cycle strobe yellow
80-87 10 50/50 duty cycle strobe green
88-95 11 Pulse strobe white
96-103 12 Pulse strobe blue
104-111 13 Pulse strobe rainbow
112-119 14 Pulse strobe red/green/blue
120-127 15 Primary/secondary chase
128-135 16 Rainbow chase
136-143 17 Yellow/blue chase
144-151 18 Red/green/blue wipe
152-159 19 Yellow/blue alternate cell chase
160-167 20 Red/blue cell chase - left/right split
168-175 21 Rainbow chase down
176-183 22 Red wipe - left/right split
184-191 23 Green wipe - left/right split
192-199 24 Blue wipe - left/right split
200-207 25 Static orange
208-215 26 Static yellow
216-223 27 Static light blue
224-231 28 Static purple
232-239 29 Static red
240-247 30 Static green
248-255 31 Static blue
Using the control menu
• When not in the menu, the four digit display shows
the current DMX address e.g. A001
• Press to enter the menu. The four digit display will
show ADDR.
• Use and to move between menu options (or to
change a value within an option).
• Press to enter an option (or to x a changed value
within an option and return to the previous option level).
Note: If you do not press to x a value, operation will
revert to the previously set mode at the next power on.
• Press to exit from a menu option (and eventually
exit the menu completely).
DMX channel and cell layouts
This section shows the different ways, when
using DMX mode, that the 8 cells can be
mapped to varying numbers of DMX chan-
nels using the PERS > RES option.
The rst channel of the xture occurs at the
DMX address selected using ADDR and
successive channels for the xture follow
from there.
Mode 24+E uses the same RGB mapping
as the 24CH layout and mode 3+E uses
the same RGB mapping as the 3CH layout,
however, the master intensity channels for
these modes are different. The 24+E and
3+E modes also use additional channels
for control of internal chase effects (see the
section below).
(* Mode DMX only, when PERS > MINT is set to ON)
