J&J Electronics PureWhite LPL-P1-WHT-12 Operating instructions

WARNING! This device is not intended for use
with emergency exit fixtures or emergency
exit lights.
WARNING! Permanent damage to the low
voltage 14VAC lamp will occur if installed on
a 120VAC circuit.
PureWhite Replacement LED In-Ground Pool lamps are available in 14VAC
(low voltage) and 120VAC models as indicated on the product packaging.
Each lamp has a screw-in Edison base.
WARNING! Remove warning label from
PureWhite lens before installation.
The warning label is placed on top of a special optical diffuser
designed to maximize the light projection of the PureWhite lamp. When
you remove the label, a protective film will come off with it. Once the
warning label and protective film have been removed, do not allow the
diffuser decal underneath to be scratched.
ATTENTION 14V PUREWHITE OWNERS!
A socket voltage range of 13.5 – 15.0 will achieve optimal brightness.
To verify the voltage, at the lamp socket, measure the open circuit
voltage (no lamp in the socket). Set the transformer tap to 14.0VAC.
DANGER!
Risk of electrical shock or electrocution
Always disconnect power to the pool light at the circuit breaker
panel before attempting to service the lamp. Failure to do so could result
in serious injury or death due to electrical shock. Refer to the original
manufacturer’s pool light installation manual before proceeding. As with
any electrical device, installation and service should always be performed
by a qualified individual. This device is not intended for use in anything
other than in-ground pools.
Rated Lamp Life
The illumination generated by the PureWhite Replacement LED In-Ground
Pool lamp is based on Light Emitting Diode (LED) technology. The average
expected lamp life is rated up to 50,000 elapsed time hours under normal
operating conditions. [Temperature: 33°F to 95°F (1°C to 35°C), Humidity:
0-95% non-condensing].
Safety Precautions
• Do not open, service or tamper with any internal component of the
PureWhite Replacement LED In-Ground Pool lamp. Doing so will
void the warranty. Follow each instruction in this owner’s manual
and pay careful attention to all warnings.
• Do not directly expose or immerse the PureWhite Replacement LED
In-Ground Pool lamp in water without containing it in a proper,
watertight, NRTL (nationally recognized testing laboratory) pool
light housing and niche assembly.
• Keep the pool light housing dry.
• Handle the PureWhite Replacement LED In-Ground Pool lamp with
care. Be careful not to drop the unit.
IMPORTANT NOTE:
PureWhite lamps are recommended for installation by a qualified pool
professional.
J&J Electronics • 35 Hammond, Irvine, CA 92618 USA • 800.735.4553 • 949.455.4460 • www.jandjpoolspa.com
PAGE 1
PureWhite™Pool Lamp Installation and Operation Guide
PUREWHITE REPLACEMENT LED IN-GROUND POOL LAMPS
Model #s: LPL-P1-WHT-12, LPL-P1-WHT-120
PureWhite Replacement LED In-Ground Pool lamps offer superior, bright white illumination for your pool. This owner’s manual contains important
information on installing and using your new PureWhite Replacement LED In-Ground Pool lamp. Please read it carefully and keep it in a safe place for
future reference.
Installation
The installation steps in this owner’s manual
are intended as guidelines. For specific
instructions on how to replace a pool lamp,
please refer to the original manufacturer’s
pool light installation manual before
proceeding.
Light housing compatibility
LPL-P1-WHT-12 and LPL-P1-WHT-120
PureWhite Replacement LED In-Ground
Pool lamps must be installed in a
compatible NRTL pool light housing.
Compatible NRTL light housings include:
Hayward®Astrolite™SP058 Series
Pentair®Amerlite 784 Series
Jacuzzi®Full Moon™
WARNING!
Read this before attempting installation
Your PureWhite lamp is not an ordinary light bulb. It is a valuable
electronic device that is not designed to come in direct contact with water.
An improper installation that results in water leakage into the pool light
housing can permanently damage the PureWhite lamp. Please read these
installation steps and the original manufacturer’s pool light installation
manual carefully before proceeding.
STEP 1
Remove light housing from niche
Make sure power to the pool light is turned off at the circuit breaker. Care-
fully remove the existing light housing from the niche assembly and place
it on the pool deck. There should be enough power cord to do this easily.
If there is not enough power cord to allow the light housing to reach the
pool deck surface, call your local pool service company.
WARNING! Verify that your PureWhite lamp
voltage rating (120VAC or 14VAC) matches
your electrical system’s voltage requirements
before proceeding with installation.

For LPL-P1-WHT-12 and LPL-P1-WHT-120
3-YEAR LIMITED WARRANTY
Product warranty
J&J Electronics, Inc. warrants the PureWhite Replacement LED
In-Ground Pool lamp (the Product) to be free from defects in material
and/or workmanship, under normal use, conditions and service, for
a period of three (3) years from the original date of purchase. If during
the warranty period, there is a defect in material or workmanship,
J&J Electronics, Inc. will repair or replace (at its discretion) the Product
under the conditions of the warranty. The warranty covers normal
consumer use of the Product. To obtain warranty service, contact
the establishment from which the Product was purchased.
Exclusions from warranty
The PureWhite Replacement LED In-Ground Pool lamp is designed
for use in In-Ground swimming pools only. If installed for use in any
other application, the warranty is void thereby releasing J&J
Electronics, Inc. from any and all claims related to its misuse. The
warranty does not cover and J&J Electronics, Inc. shall be held
harmless against any damage occurring during shipment, damage
or failure resulting from alteration, accident, theft, abuse, negligent
installation, improper service, unauthorized repairs or where adequate
care has not been taken to prevent damage to the Product. Tampering
with any internal component of this Product will void the warranty.
This warranty does not cover failure due to the presence of water
inside the niche fixture. This warranty excludes all incidental or
consequential damages except as required by state law. This warranty
gives you specific rights. You may have other rights that vary
according to the laws of your state.
STEP 2
Remove old lamp
Access the old lamp according to the original manufacturer’s pool light
installation manual. Remove the screws and/or loosen the clamp that holds
the face plate and lens in place. Carefully remove the lens from the pool
light housing. Take care not to damage the surface of the light housing
body that makes contact with the rubber gasket.
STEP 3
Inspect your light housing for signs of wear
Inspect the rubber grommet where the power cord enters the light for
excessive deterioration. Inspect the light housing, the tensioning clamp,
and face ring for warping, dents and excessive rust. Do not install
PureWhite into a pool light housing that appears to be worn out from
prolonged exposure to pool water or mishandling.
STEP 4
Dry the light housing and lens
Make sure the inside of the light housing and glass lens are completely
dry by wiping them down with a clean rag.
STEP 5
Install PureWhite lamp
Remove the old lamp and discard. Carefully screw the PureWhite lamp
into the socket.
STEP 6
Reassemble the light housing
Proceed by cleaning any gasket residue from the light housing body. A
clean surface is necessary for the new gasket to seat properly and prevent
leakage. Install the new gasket onto the glass lens.
WARNING! Always use a new lens gasket
whenever reassembling your pool light housing.
Failure to install a new lens gasket could result in water leakage
which can permanently damage the PureWhite lamp and cause serious
injury or death due to electrical shock.
Set the lens and faceplate in the light housing and re-assemble according
to the light housing manufacturer’s specification. Tighten the screws or
clamp slightly, allowing the gasket to seal evenly.
STEP 7
Submerge assembled light into the water
Once the screws or clamp are tight, submerge the assembled light housing
in the water and visually check that air bubbles are not escaping from the
gasket area. Should bubbles appear, immediately remove the light housing
from the water and reset the gasket and lens.
Once you are satisfied that there are no air leaks, complete the installation
by wrapping the cord around the light housing and re-attaching the light
housing to the niche assembly.
STEP 8
Check for air bubbles when light is turned ON
Reconnect power to the pool light by resetting the circuit breaker to the
“ON” position. Go back to the light location and check for air bubbles
rising to the surface from the pool light housing for at least 10 minutes.
It is important that the lamp is turned on during this time.
If you do not see air bubbles rising to the surface at anytime during the
10-minute inspection process, the housing is holding its water tight seal
and the installation is complete. You are now ready to enjoy your new
PureWhite Replacement LED In-Ground Pool lamp.
If you do see air bubbles rising to the surface at anytime during the
inspection process, immediately remove the PureWhite lamp from the
housing, dry it completely and reset the gasket and lens. Make sure that the
PureWhite lamp and light housing are completely dry before reassembling.
If the pool light housing continually leaks water after 2 or more attempts
at installation, replacement of the pool light housing may be necessary.
Please read the J&J Electronics”PureWhite Quick Start Guide” for further
installation advice.
Note on Figures 1-3: All figures are provided for illustration purposes only.
Refer to the original pool light manufacturer’s installation manual for
further reference.
Operation
For LPL-P1-WHT-12, LPL-P1-WHT-120 PureWhite Replacement LED
In-Ground Pool Lamps
Use the pool’s current light switch to turn “ON” and “OFF” your new
PureWhite lamp.
For more information about this or other J&J Electronics lighting products, please visit www.purewhitepoollight.com. Rev. 012910
©2010 J&J Electronics, Inc. All rights reserved. PureWhite is a trademark of J&J Electronics, Inc. All registered and trademarked brands and names are the property of their respective companies.
J&J Electronics • 35 Hammond, Irvine, CA 92618 USA • 800.735.4553 • 949.455.4460 • www.jandjpoolspa.com
PAGE 2