Jardine BRADFORD 0316T00 User manual

Model #:
0316T00 - DARK WALNUT
0316T00JW - DARK WALNUT
NOTE:
This instruction booklet containes
IMPORTANT safety information.
Please read and keep for future reference.
BRADFORD 4-IN-1 CRIB
DO NOT RETURN PRODUCT TO THE
STORE.
If a part is missing or damaged, contact our
customer service department. We will
replace the part FREE of charge.
Tel #: [phone]
E-Mail: c[email protected]
Fax #: [phone]
Receipt of Purchase:
ATTACH HERE
NEED HELP!
CALL US FOR ASSISTANCE
1-800-295-1980
DO NOT RETURN PRODUCT TO STORE
E-MAIL:[e-mail]
DATE OF PURCHASE:

*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Follow warnings on all products in a crib.
WARNING ENTRAPMENT / STRANGULATION HAZARD:
*Infants have died in toddler beds from entrapment and strangulation.
*NEVER use bed with children under 15 months.
*NEVER place bed near windows where cords from blinds or drapes may strangle a child.
*
*
*
*
*
Customer Service Department No. 413
12345 Albert-Hudon Boulevard, Suite 100
Montreal, Quebec
Canada H1G 3L1
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact our customer service representative first!
CALL 1-800-295-1980
You can also order parts by writing to the address listed below. Please include the product model number, color
and a detailed description of the part.
Before each usage or assembly, inspect crib for damaged hardware, loose joints, missing parts or
sharp edges, DO NOT use crib if any parts are missing or broken. Ask your dealer or write to our
customer service representative (address & phone number shown above) for replacement parts and
instructional literature if needed. DO NOT substitute parts.
Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional
padding under an infant.
When child is able to climb out or reaches the height of 35 inches (90 cm), the crib shall no longer be
used.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep,
unless otherwise advised by your physician.
E-MAIL: [email protected]
WARNING
Failure to follow these warnings and assembly instructions could result in serious injury or death.
Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE.
When child is able to pull to standing position, set mattress to lowest position and remove bumper
pads, large toys and other objects that could serve as steps for climbing out.
Never use plastic shipping bags or other plastic film as mattress covers because they can cause
suffocation.
DO NOT use a water mattress with this crib.
Replace teething rail if damaged or loose (if teething rail is provided for this model).
DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Strings can cause strangulation! DO NOT place crib with a string around a child's neck, such as hood
strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on
loose fasteners.
If refinishing, use a non-toxic finish specified for children's products.
DO NOT place DAY BED or TODDLER BED near windows where cords from blinds or drapes may
strangle a child.
DO NOT place items with a string, cord, or ribbon around a child's neck, such as hood strings or
pacifier cords.
DO NOT suspend strings over a TODDLER BED or DAY BED for any reason.
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 INCHES BY 51-5/8
INCHES (69CM BY 131CM) WITH A MINIMUM THICKNESS OF 4 INCHES (10CM) BUT NOT
EXCEEDING 6 INCHES (15CM).
Infants can suffocate in gaps between crib sides and a mattress that is too small.
The TODDLER BED or DAY BED is not intended for children under 15 months of age or over 50
If guardrails are used as the mattress containment means, guardrail(s) provided must be used to avoid
the formation of a gap between the mattress and the bed that could cause an entrapment (when
product is used as a TODDLER BED or DAY BED).

*
*
*
*
*
*
NOTES
CAUTION: Adult assembly required.
Assembly will require two people.
WARNING: Should this product become damaged,
and/or components are broken or missing, DO NOT
USE.
CARE AND CLEANING
Ensure all parts and components are present before beginning assembly.
Assemble on soft, smooth surface to prevent damage to product finish.
Phillips head screw driver is not included.
DO NOT use power tools.
LIMITED WARRANTY
Jardine Enterprise warrants its product to be free from defects in material and workmanship and
agrees to remedy any such defect. This warranty covers 1 year from the date of original purchase.
This warranty is valid only upon presentation of proof of purchase. This is solely limited to the
repair or replacement of defective furniture components and no assembly labor is included. This
warranty does not apply to any product which has been improperly assembled, subjected to misuse
or abuse or which has been altered or repaired in any way. This warranty gives you specific legal
rights and you may also have other rights which vary from State to State.
Dust regularly with a soft, lint-free cloth to prevent soil build-up. A damp cloth may be used
occasionally to clean surface. Dry immediately. Do not use any abrasives that may damage finish.
Excessive exposure to sunlight and extreme changes in temperature and moisture can damage
wood furniture.
If the crib is to be stored, store in cool dry place and carefully package all original hardware to
protect from loss.
MAINTENANCE
Check bolts/screws periodically and tighten them if necessary.

BRADFORD 4 IN 1 CRIB
1
PARTS LIST
MATTRESS SUPPORT
1 PC
FRONT PANEL
1 PC
HEADBOARD
1 PC
LEFT FRONT POST
1 PC RIGHT FRONT POST 1 PC
LEFT END PANEL
1 PC RIGHT END PANEL
1 PC
GUARDRAIL
1 PC
HARDWARE LIST
BOLT
4 PCS
ALLEN KEY
1 PC
BOLT
16 PCS
BOLT
4 PCS
4-1/2"x 1/4"
BOLT
4 PCS
3"x 1/4" 2-1/2"x 1/4"
4MM
1/2"× 1/4"

count all parts and compare with the parts list.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of a turn. After crib
is completely assembled, return to each bolt and tighten them. Use wax or soap on all bolts to
facilitate assembly.
* Please make sure that the top of
the post is flush with the top of
curving rail on end panel when
tightening bolts.
* Please make sure that the top of
the post is flush with the top of
curving rail on end panel when
tightening bolts.
STEP 2
Attach the left & right end panels (A1) & (A2) to headboard with bolts (2)&(3). Use Allen Key (5) to tighten
bolts.
BRADFORD 4 IN 1 CRIB
STEP 1
Attach the right front post (B2) to the right end panel (A2) with the wood dowel, bolt (2) and bolt (3). Use
Allen Key (5) to tighten bolts. Repeat this step for the left front post (B1) and left end panel (A1).
Thank you for purchasing this quality product. Be sure to check all packing material carefully
for small parts, which may have come loose inside the carton during shipment. Identify and
C
5
A2
B2
A1
B1
2
3
3
WOOD DOWEL
WOOD DOWEL
53
B1
A1 B2
A2
3
2

STEP 3:
BRADFORD 4 IN 1 CRIB
Attach the mattress support to the 4 corner posts with the mattress support bolts (4). Use
Allen Key to tighten bolts. Refer to details 1 and 2 for direction on how to properly attach the
mattress support.
INCORRECT-
Tabs on corners
of mattress
support should
point up
INCORRECT-
Raised edge
should face
down -this
photo shows
mattress
support is
upside down
CORRECT
*Tabs to point UP.
*Flat surface of mattress support to face up
- mattress must sit on flat surface.
G
G
G
N

STEP 4
Attach the front panel (D) to the front posts (B1 & B2) with bolts (1). Use Allen Key (5) to tighten bolts.
NOTE: When the child is able to stand on his/her own, place the mattress support at its lowest
position.
BRADFORD 4 IN 1 CRIB
1
5
1
B2
D
B1
1
1

WARNINGS:
*The DAY BED is not intended for children under 15 months of age or over 50 pounds.
STEP 1: Detach the front panel (D) from the front posts (B1 & B2) by using Allen Key (5).
STEP 1: Follow step 1 to 3 of the crib assembly instruction.
BRADFORD 4 IN 1 CRIB
STEP 2: Follow step 2 to 3 for the day bed assembly instruction located above (starting from crib).
DAY BED ASSEMBLY INSTRUCTION: STARTING FROM CRIB
STEP 2: Move the mattress support (E) to the lowest position by adjusting bolts with Allen key (5).
*Any mattress used in this crib must be at least 27-1/4 inches by 51-5/8 inches (69cm by 131cm)
with a minimum thickness of 4 inches (10cm) but not exceeding 6 inches (15cm).
NOTE: When inserting bolts turn clockwise until tight. Then loosen 1/2-3/4 of a turn. After crib
is completely assembled, return to each bolt and tighten. Use wax or soap on all bolts to
facilitate assembly.
STEP 3: Attach the guardrail (F) to the front posts (B1 & B2) with bolts (1). Use Allen Key (5) to tighten
the bolts.
DAY BED ASSEMBLY INSTRUCTION: STARTING FROM SCRATCH
1
1B1
FB2 1
1
5

STEP 2: Assemble the full size conversion rails (not included) to the headboard (C)
and the front posts (B1 &B2) as shown in diagram 2.
STEP 1: Assemble the front posts (B1 &B2) to the front panel (D) with bolts (1) .Use Allen
Key (5) to tighten the bolts as shown in diagram1.
FULL SIZE CONVERSION RAILS ARE NOT INCLUDED. DIAGRAM 2 IS FOR REFERENCE
ONLY.CONVERSION RAILS MAY DIFFER FROM ILLUSTRATION.
BRADFORD 4 IN 1 CRIB
I
I
J
H1
Headboard
Footboard
Headboard
SIDE RAIL
WOOD SCREWS
SLAT
NOTE:
DIAGRAM 1
DIAGRAM 2
A
5
FOOTBOARD
DIAGRAM 2
FOOTBOARD
DIAGRAM 1