Jardine Madison DA833BC User manual

Model # DA833BC- Madison Single Crib (Natural)
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Follow warnings on all products in a crib.
*
*
*
*
*
*
Customer Service Department No. 413
12345 Albert-Hudon Boulevard, Suite 100
Montreal, Quebec
Canada H1G 3L1
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact our customer service representative first!
CALL 1-800-295-1980
You can also order parts by writing to the address listed below. Please include the product model number, color
and a detailed description of the part.
Before each usage or assembly, inspect crib for damaged hardware, loose joints, missing parts or
sharp edges, DO NOT use crib if any parts are missing or broken. Ask your dealer or write to our
customer service representative (address & phone number shown above) for replacement parts and
instructional literature if needed. DO NOT substitute parts.
Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding
under an infant.
When child is able to climb out or reaches the height of 35 inches (90 cm), the crib shall no longer be
used.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep,
unless otherwise advised by your physician.
E-MAIL: [e-mail]
WARNING
Failure to follow these warnings and assembly instructions could result in serious injury or death.
Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE.
When child is able to pull to standing position, set mattress to lowest position and remove bumper
pads, large toys and other objects that could serve as steps for climbing out.
Never use plastic shipping bags or other plastic film as mattress covers because they can cause
suffocation.
DO NOT use a water mattress with this crib.
Replace teething rail if damaged or loose (if teething rail is provided for this model).
DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Strings can cause strangulation! DO NOT place crib with a string around a child's neck, such as hood
strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on
loose fasteners.
If refinishing, use a non-toxic finish specified for children's products.
Assemble on soft, smooth surface to prevent damage to product finish.
Phillips head screw driver is not included.
DO NOT use power tools.
CAUTION: Adult assembly required.
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 INCHES BY 51-5/8
INCHES (69CM BY 131CM) WITH A MINIMUM THICKNESS OF 4 INCHES (10CM) BUT NOT
EXCEEDING 6 INCHES (15CM).
Infants can suffocate in gaps between crib sides and a mattress that is too small.
NOTES
Ensure all parts and components are present before beginning assembly.
Assembly will require two people.

Model # DA833BC- Madison Single Crib (Natural)
Jardine Enterprise warrants its product to be free from defects in material and workmanship and
agrees to remedy any such defect. This warranty covers 1 year from the date of original purchase.
This warranty is valid only upon presentation of proof of purchase. This is solely limited to the
repair or replacement of defective furniture components and no assembly labor is included. This
warranty does not apply to any product which has been improperly assembled, subjected to misuse
or abuse or which has been altered or repaired in any way. This warranty gives you specific legal
rights and you may also have other rights which vary from State to State.
If the crib is to be stored, store in cool dry place and carefully package all original hardware to
protect from loss.
MAINTENANCE
Check bolts/screws periodically and tighten them if necessary.
LIMITED WARRANTY
WARNING: Should this product become
damaged, and/or components are broken or missing,
DO NOT USE.
CARE AND CLEANING
Dust regularly with a soft, lint-free cloth to prevent soil build-up. A damp cloth may be used
occasionally to clean surface. Dry immediately. Do not use any abrasives that may damage finish.
Excessive exposure to sunlight and extreme changes in temperature and moisture can damage
wood furniture.

HARDWARE AND PART LIST
ASSEMBLY INSTRUCTIONS FOR "DA833BC"
RUBBER BUMPER 2PCS
A
B
ALLEN WRENCH 4MM 1PC
C
F
G
STABILIZING BAR 1PC
MACHINE SCREW 2PCS
LEFT END PANEL 1PC
0.3805"×0.1785"DIA
MATTRESS SUPPORT BOLT 16PCS
1/2"×1/4"DIA
D
BOLT 3 1/4"×1/4"DIA 2PCS
BOLT 2"×1/4"DIA 10PCS
BOLT 5"×1/4"DIA 2PCS
E
LEFT END 1PC
RIGHT END 1PC
END PANEL
STATIONARY SIDE 1PC
DROP SIDE 1PC
MATTRESS SUPPORT 1PC
RIGHT FRONT POST 1PC
LEFT FRONT POST 1PC
LEFT BACK POST 1PC
RIGHT BACK POST 1PC
I1
I2
J
L1
L2
L3
L4
H
K
M

Thank you for purchasing this quality product. Be sure to check all packing material carefully
for small parts, which may have come loose inside the carton during shipment. Identify and
count all parts and compare with the parts list below.
NOTE: WHEN INSERTING SCREWS TURN CLOCKWISE UNTIL TIGHT. THEN LOOSEN
1/2-3/4 OF A TURN. AFTER CRIB IS COMPLETELY ASSEMBLED, RETURN TO EACH
SCREW AND TIGHTEN. USE WAX OR SOAP ON ALL SCREWS TO FACILITATE ASSEMBLY.
STEP 1:
TO ATTACH THE RIGHT BACK POST
(PART L2) TO THE RIGHT END
PANEL (PART I2) , FIRST ALIGN THE
WOOD DOWEL (PRE-SET ON THE RIGHT
END PANEL (PART I2) AND THE TOP
PRE- DRILLED HOLE ON THE RIGHT
BACK POST (PART L2). THEN USE 2
BOLTS (PART C) AND WRENCH
(PART D) PROVIDED TO SECURE THE
RIGHT END PANEL (PART I2) AND
RIGHT BACK POST (PART L2).
REPEAT THIS STEP FOR THE LEFT
FRONT POST (PART L1) AND
LEFT END PANEL (PART I1).
STEP 2:
TO ATTACH THE RIGHT FRONT POST
(PART L3) TO THE RIGHT END
PANEL (PART I2) , FIRST ALIGN THE
WOOD DOWEL (PRE-SET ON THE RIGHT
END PANEL (PART I2) AND THE TOP
PRE- DRILLED HOLE ON THE RIGHT
FRONT POST (PART L3). THEN USE 2
BOLTS (PART C) AND WRENCH
(PART D) PROVIDED TO SECURE THE
RIGHT END PANEL (PART I2) AND
RIGHT FRONT POST (PART L3).
REPEAT THIS STEP FOR THE LEFT
FRONT POST (PART L4) AND
LEFT END PANEL (PART I1).
PLEASE MAKE SURE THAT THE TOP OF
THE POST IS AT THE LOWEST POSITION
TO BE CONNECTED TO THE TOP OF THE
RAIL OF THE END PANEL WHILE
SCREWING.
C
D
C
L4
L3
I1
I2
C
C
WOOD DOWEL
WOOD DOWEL
L1
C
L2
C
I2
I1
C
D
WOOD DOWEL
C
WOOD DOWEL

STEP 3:
STEP 4:
Attach stabilizing bar (H) to end panels (I1) and (I2), using bolts(C). Use
Allen wrench (D)to tighten bolts.
Attach stationary side(J) to left and right back post (L1 and L2), using bolts (A) and (B).
Use Allen wrench (D) to tighten bolts.
NOTE: WHEN INSTALLING THE STATIONARY SIDE AND DROP SIDE, PLEASE ENSURE
THE TEETHING RAIL IS ON TOP.
C
D
C
J
H
L4
D
A
A
J
I1
B
B
I2
L2

STEP 5:
Attach the mattress support to the 4 corner posts with the mattress support bolts (E). Use Allen Key to
tighten bolts. Refer to details 1 and 2 for direction on how to properly attach the mattress support.
INCORRECT-
Tabs on corners
of mattress
support should
point up
INCORRECT-
Raised edge
should face
down -this
photo shows
mattress
support is
upside down
CORRECT
*Tabs to point UP.
*Flat surface of mattress support to face up
- mattress must sit on flat surface.
G
G
G
N

ALIGN AND SLIDE DROP SIDE FROM THE BOTTOM ONTO THE DROP SIDE UPPER AND LOWER TRACKS ON THE LEFT
OF THE LOWER DROP SIDE TRACKS (PULL TOWARDS YOU). RAISE DROPSIDE UNTIL IT IS LOCKED INTO PLACE.
CAUTION: DO NOT FORCE THE DROP SIDE AS YOU MAY BREAK THE LOCKS, GUIDES, OR TRACKS.
ATTACH RUBBER STOPPERS BEFORE OPERATING DROP SIDE.
Note: When moving the crib, DO NOT hold it by the drop side, always use the side frames to move the crib.
WHEN ASSEMBLING THE DROP SIDE, MAKE SURE THE TEETHING RAIL IS ON THE TOP.
PHOTO A PHOTO B
STAND AT THE MIDDLE OF THE DROP SIDE AND HOLD THE TOP RAIL WITH ONE HAND. RAISE THE DROP SIDE
SLIGHTLY TO ENABLE YOU TO RELEASE THE LATCH BY PUSHING ON THE DROP SIDE LOWER RAIL WITH YOUR KNEE.
THE DROP SIDEWILL NOW LOWER. RAISE THE DROP SIDE AND IT WILL AUTOMATICALLY LOCK AT THE UPPER
POSITION.
ALWAYS MAKE SURE DROP SIDE IS PROPERLY SECURED.
STEP 6
AND RIGHT FRONT POSTS. MAKE SURE THE RELEASE LATCH ON THE LOWER GUIDES IS TO THE OUTSIDE
The release latch on the lower
guides must be on the outside
of the lower drop side tracks -
pull towards you before sliding
onto the track.
This rubber bumper must be installed prior
to operating drop side - it will prevent drop
side from falling to the floor
NOTE: Photos A & B are to demonstrate how the drop side should be installed.The photos of the wood components of the
crib may differ from the crib purchased and are for reference only.
OPERATING INSTRUCTIONS FOR DROP SIDE.
Email: [e-mail]
AFTER DROP SIDE IS
INSTALLED ON THE TRACKS
AND LATCHED IN THE "UP"
POSITION, THREAD MACHINE
SCREW INTO A RUBBER
STOPPER AND INSERT INTO
EMPTY HOLE ON LOWER TRACK
ASSEMBLY. USE PHILLIPS
SCREW- DRIVER
(NOT PROVIDED)
TO TIGHTEN BOLT.
Machine Screw (6)
Rubber Stopper
K
I2
J
PUSH
RUBBER BUMPER(5)
BOLT (6)
FRONT POST
ALIGN UPPER
GUIDE WITH
UPPER TRACK
LOWER TRACK ASSEMBLY
FACTORY INSTALLED
ALIGN LOWER
GUIDE ASSEMBLY
WITH LOWER
TRACK ASSEMBLY
UPPER GUIDE
(ATTACHED TO
CRIB DROPSIDE (PART C)
BOTTOM EDGE OF
CRIB DROPSIDE(PART C)
LOWER GUIDE
ASSEMBLY
ON DROPSIDE(PART C)
ALLGN BOTH TRACKS FROM
UNDERNEATH THEN PULL UP UNTIL LOWER GULDE LATCHES