Jardine DA616BC User manual

MODEL # DA616BC (DARK PINE) / DA616BN (NATURAL)
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Follow warnings on all products in a crib.
WARNING ENTRAPMENT / STRANGULATION HAZARD:
*Infants have died in toddler beds from entrapment and strangulation.
*NEVER use bed with children under 15 months.
*NEVER place bed near windows where cords from blinds or drapes may strangle a child.
*
*
*
*
*
Customer Service Department No. 413
12345 Albert-Hudon Boulevard, Suite 100
Montreal, Quebec
Canada H1G 3L1
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact our customer service representative first!
CALL 1-800-295-1980
You can also order parts by writing to the address listed below. Please include the product model number, color
and a detailed description of the part.
Before each usage or assembly, inspect crib for damaged hardware, loose joints, missing parts or
sharp edges, DO NOT use crib if any parts are missing or broken. Ask your dealer or write to our
customer service representative (address & phone number shown above) for replacement parts and
instructional literature if needed. DO NOT substitute parts.
Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional
padding under an infant.
When child is able to climb out or reaches the height of 35 inches (90 cm), the crib shall no longer be
used.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep,
unless otherwise advised by your physician.
E-MAIL: [email protected]
WARNING
Failure to follow these warnings and assembly instructions could result in serious injury or death.
Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE.
When child is able to pull to standing position, set mattress to lowest position and remove bumper
pads, large toys and other objects that could serve as steps for climbing out.
Never use plastic shipping bags or other plastic film as mattress covers because they can cause
suffocation.
DO NOT use a water mattress with this crib.
Replace teething rail if damaged or loose (if teething rail is provided for this model).
DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Strings can cause strangulation! DO NOT place crib with a string around a child's neck, such as hood
strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on
loose fasteners.
If refinishing, use a non-toxic finish specified for children's products.
DO NOT place DAY BED or TODDLER BED near windows where cords from blinds or drapes may
strangle a child.
DO NOT place items with a string, cord, or ribbon around a child's neck, such as hood strings or
pacifier cords.
DO NOT suspend strings over a TODDLER BED or DAY BED for any reason.
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 INCHES BY 51-5/8
INCHES (69CM BY 131CM) WITH A MINIMUM THICKNESS OF 4 INCHES (10CM) BUT NOT
EXCEEDING 6 INCHES (15CM).
Infants can suffocate in gaps between crib sides and a mattress that is too small.
The TODDLER BED or DAY BED is not intended for children under 15 months of age or over 50
If guardrails are used as the mattress containment means, guardrail(s) provided must be used to avoid
the formation of a gap between the mattress and the bed that could cause an entrapment (when
product is used as a TODDLER BED or DAY BED).

MODEL # DA616BC (DARK PINE) / DA616BN (NATURAL)
*
*
*
*
*
*
NOTES
CAUTION: Adult assembly required.
Assembly will require two people.
WARNING: Should this product become damaged,
and/or components are broken or missing, DO NOT
USE.
CARE AND CLEANING
Ensure all parts and components are present before beginning assembly.
Assemble on soft, smooth surface to prevent damage to product finish.
Phillips head screw driver is not included.
DO NOT use power tools.
LIMITED WARRANTY
Jardine Enterprise warrants its product to be free from defects in material and workmanship and
agrees to remedy any such defect. This warranty covers 1 year from the date of original purchase.
This warranty is valid only upon presentation of proof of purchase. This is solely limited to the
repair or replacement of defective furniture components and no assembly labor is included. This
warranty does not apply to any product which has been improperly assembled, subjected to misuse
or abuse or which has been altered or repaired in any way. This warranty gives you specific legal
rights and you may also have other rights which vary from State to State.
Dust regularly with a soft, lint-free cloth to prevent soil build-up. A damp cloth may be used
occasionally to clean surface. Dry immediately. Do not use any abrasives that may damage finish.
Excessive exposure to sunlight and extreme changes in temperature and moisture can damage
wood furniture.
If the crib is to be stored, store in cool dry place and carefully package all original hardware to
protect from loss.
MAINTENANCE
Check bolts/screws periodically and tighten them if necessary.

ASSEMBLY INSTRUCTION FOR DA616BC & DA616BN
PARTS LIST
LONG BOLT 4 1/4"×1/4" DIA 6PCS
ALLEN WRENCH 4MM 1PC
4PCS
SHORT BOLT 3"×1/4" DIA 2PCS
MATTRESS SUPPORT BOLT RUBBER BUMPER
0.3805"×0.1785"DIA
MACHINE SCREW 2PCS
35×7MM
GUARD RAIL 1PC
DROP SIDE 1PC
WOOD SCREWS
1" 12PCS
MATTRESS SUPPORT 1PC
DRAWER 1PC
A
B
C
D
E
F
I
J
1/2"×1/4"DIA
M
N
STATIONARY SIDE 1PC
RIGHT END PANEL 1PC
LEFT END PANEL 1PC
MINIFIT HOUSING
MINIFIT SCREW 8PCS
1/2"×14MM
H
SHORT BOLT 2"×1/4" DIA 2PCS
K
L1
L2
G
2PCS
O
P
Q
STABLIZING BAR 1PC

ASSEMBLY INSTRUCTION
Thank you for purchasing this quality product.Be sure to check all packing material carefully for
small parts, which may have some loose inside the carton during shipment. Identify and count all
part sent compare with the parts list.
Cleaning instruction:Clean the table surface with a furniture polish and a soft cloth.
NOTE:WHEN INSERTING SCREWS TURN CLOCKWISE UNTIL TIGHT, THEN LOOSEN 1/2--3/4
OF A TURN. AFTER CRIB IS COMPLETELY ASSEMBLED,RETURN TO EACH SCREW AND
TIGHTEN, USE WAX OR SOAP ON ALL SCREWS TO FACILITATE ASSEMBLY.
STEP 1
Assemble the stationary side frame
(part M) with end panels (part L1& L2)
using the bolts (part A & C) and Allen
wrench provided. Please place bolt A
& C in right position as picture showing.
To attach part (K) to parts(L),
insert hardware (H) into parts (L)
to lock part(K) in place by using
hardware(B).
DA616BC & DA616BN CRIB WITH DRAWER
1
M
L1
L2
B
A
H
C
K

STEP 2
DA616BC & DA616BN CRIB WITH DRAWER
ASSEMBLY INSTRUCTION
Attach the mattress support to the 4 corner posts with the mattress support bolts (D). Use
Allen Key to tighten bolts. Refer to details 1 and 2 for direction on how to properly attach the
mattress support.
INCORRECT-
Tabs on corners
of mattress
support should
point up
INCORRECT-
Raised edge
should face
down -this
photo shows
mattress
support is
upside down
CORRECT
*Tabs to point UP.
*Flat surface of mattress support to face up
- mattress must sit on flat surface.
G
G
G
N

ALIGN AND SLIDE DROP SIDE FROM THE BOTTOM ONTO THE DROP SIDE UPPER AND LOWER TRACKS ON THE LEFT
OF THE LOWER DROP SIDE TRACKS (PULL TOWARDS YOU). RAISE DROPSIDE UNTIL IT IS LOCKED INTO PLACE.
CAUTION: DO NOT FORCE THE DROP SIDE AS YOU MAY BREAK THE LOCKS, GUIDES, OR TRACKS.
ATTACH RUBBER STOPPERS BEFORE OPERATING DROP SIDE.
Note: When moving the crib, DO NOT hold it by the drop side, always use the side frames to move the crib.
WHEN ASSEMBLING THE DROP SIDE, MAKE SURE THE TEETHING RAIL IS ON THE TOP.
PHOTO A PHOTO B
STAND AT THE MIDDLE OF THE DROP SIDE AND HOLD THE TOP RAIL WITH ONE HAND. RAISE THE DROP SIDE
SLIGHTLY TO ENABLE YOU TO RELEASE THE LATCH BY PUSHING ON THE DROP SIDE LOWER RAIL WITH YOUR KNEE.
THE DROP SIDEWILL NOW LOWER. RAISE THE DROP SIDE AND IT WILL AUTOMATICALLY LOCK AT THE UPPER
POSITION.
ALWAYS MAKE SURE DROP SIDE IS PROPERLY SECURED.
OPERATING INSTRUCTIONS FOR DROP SIDE.
STEP 3
AND RIGHT FRONT POSTS. MAKE SURE THE RELEASE LATCH ON THE LOWER GUIDES IS TO THE OUTSIDE
ASSEMBLY INSTRUCTION
DA616BC & DA616BN CRIB WITH DRAWER
The release latch on the lower
guides must be on the outside
of the lower drop side tracks -
pull towards you before sliding
onto the track.
This rubber bumper must be installed prior
to operating drop side - it will prevent drop
side from falling to the floor
NOTE: Photos A & B are to demonstrate how the drop side should be installed.The photos of the wood components of the
crib may differ from the crib purchased and are for reference only.
Email: [e-mail]
AFTER DROP SIDE IS
INSTALLED ON THE TRACKS
AND LATCHED IN THE "UP"
POSITION, THREAD MACHINE
SCREW INTO A RUBBER
STOPPER AND INSERT INTO
EMPTY HOLE ON LOWER TRACK
ASSEMBLY. USE PHILLIPS
SCREW- DRIVER
(NOT PROVIDED)
TO TIGHTEN BOLT.
Machine Screw (F)
Rubber Stopper
L1
L2
M
N
RUBBER BUMPER(5)
BOLT (6)
FRONT POST
ALIGN UPPER
GUIDE WITH
UPPER TRACK
LOWER TRACK ASSEMBLY
FACTORY INSTALLED
ALIGN LOWER
GUIDE ASSEMBLY
WITH LOWER
TRACK ASSEMBLY
UPPER GUIDE
(ATTACHED TO
CRIB DROPSIDE (PART C)
BOTTOM EDGE OF
CRIB DROPSIDE(PART C)
LOWER GUIDE
ASSEMBLY
ON DROPSIDE(PART C)
ALLGN BOTH TRACKS FROM
UNDERNEATH THEN PULL UP UNTIL LOWER GULDE LATCHES

Step 4:
Inserting screw (part J ) into the nylon
nuts on drawer sides (A1&A2) and
front (B) by rotating it clockwise.
Step 5
Inserting (G) into the pre-drilled
holes of drawer back (E). make
sure it's open mouth towards the
holes, Secondly attaching left
drawer side (A2) and right drawer
side (A1) to the drawer back (E)
by inserting screw (part J ) onto
the (G) , and then tighten it by
rotating (G) clockwise with
screwdriver, as in diagram 2.
Step 6
Align and insert drawer bottom (F)
into the grooves of drawer sides
(A1&A2) and drawer back (E),
as in diagram 3.
Step 7
Inserting (G) into the pre-drilled holes
of drawer sides (A1&A2), make sure
it's open mouth towards the holes, and
then attaching drawer front (B) to the
drawer sides and drawer bottom, at
last tighten it by rotating (G)
clockwise with screwdriver, as in
diagram 4.
Step 8
Inverting the drawer and tighten it by
using phillips screwdriver and 12 pcs
screws provided. as in diagram 5.
ASSEMBLY INSTRUCTIONS FOR DA616BC / DA616BN
TRUNDLE DRAWER
J
J
DIAGRAM 1
J
DIAGRAM 2
G
E
DIAGRAM 3
F
A1
A2
DIAGRAM 4
G
A1
A2
B
E
E
DIAGRAM 5
Q

STEP 9
ASSEMBLY INSTRUCTION
DA616BC & DA616BN CRIB WITH DRAWER
P
CAREFULLY LAY THE CRIB DOWN ON A FLAT, SMOOTH SURFACE (CLEAN CLOTH OR CARPET)
WITH DROPSIDE FACE UP. INSERT DRAWER INTO THE TRACKS FROM TOP (FOR EASE OF
INSTALLATION WE RECOMMEND TWO PEOPLE INSTALL TRUNDLE DRAWER INTO TRACKS) AND
LET IT SLIDE DOWN INTO THE CRIB. THEN TURN CRIB BACK TO NORMAL POSITION. (DRAWER
ASSEMBLY INSTRUCTION SEE ATTACHED).

DAY BED
WARNINGS:
1. ANY MATTRESS USED IN THIS DAY BED MUST BE AT LEAST
27-1/4" × 51-5/8" (69CM × 131CM) WITH A MINIMUM THICKNESS OF 4"
AND NOT EXCEEDING 6" (15CM).
2. THE DAY BED IS INTENDED FOR USE BY A CHILD NOT LESS THAN 15 MONTHS
OF AGE AND WHO WEIGHTS NO MORE THAN 50LBS (27.7KGS)
NOTE: WHEN INSERTING SCREWS TURN CLOCKWISE UNTIL TIGHT, THEN LOOSEN
1/2-3/4 OF A TURN, AFTER CRIB IS COMPLETELY ASSEMBLED, RETURN TO EACH
SCREW AND TIGHTEN, USE WAX OR SOAP ON ALL SCREWS TO FACILITATE ASSEMBLY.
DAY BED ASSEMBLY INSTRUCTIONS, STARTING FROM CRIB
STEP 1: UNSCREW THE RUBBER BUMPER STOP (PART E) FROM THE LOWER DROPSIDE
TRACK ON THE LEFT (PART L1) AND RIGHT (PART L2) FRONT POSTS.
STEP 2: DETACH THE DROPSIDE (PART N) FROM THE LEFT AND RIGHT POSTS BY SLIDING
THE UPPER AND LOWER GUIDES ON EACH END OF THE DROPSIDE DOWN UNTIL
THEY ARE BELOW THE UPPER AND LOWER DROPSIDE TRACK. ONCE THE
DROPSIDE HITS THE FLOOR, THE GUIDES AND TRACKS CAN BE SEPARATED
FROM EACH OTHER.
STEP 3: UNSCREW AND DETACH THE LOWER TRACKS FROM THE LEFT AND RIGHT FRONT
POSTS.
STEP 4: IF MATTRESS SUPPORT (PART O) IS NOT IN THE LOWEST POSITION,UNSCREW
MATTRESS SUPPORT BOLTS (PART D) FROM POST AND MOVE IT TO THE LOWEST
POSITION.
STEP 5: USING THE WRENCH PROVIDED, ATTACH THE GUARD RAIL (PART I)
USING 4 BOLTS (PART A) BETWEEN THE LEFT AND FIGHT FRONT POSTS.
STEP 6: TIGHTEN ALL SCREWS CLOCKWISE.
STARTING FROM SCRATCH:
STEP 1: FOLLOW STEPS 1 TO 2 OF THE CRIB ASSEMBLY INSTRUCTIONS.
STEP 2: FOLLOW STEPS 3 TO 6 FOR THE DAY BED ASSEMBLY INSTRUCTIONS LOCATED
ABOVE (STARTING FROM CRIB).
PLEASE ENSURE THAT THE HEIGHT ADJUSTMENT HOLES BE FILLED
WITH SCREWS (D) AFTER THE MATTRESS SUPPORT BEEN MOVED TO THE
LOWEST LEVEL,MAKE SURE THAT THESE SCREWS ARE TIGHTLY
NOTE:
L1
L2
M
I
A
B
B
A
PLEASE ENSURE THAT THE HEIGHT ADJUSTMENT HOLES BE FILLED
WITH SCREWS (D) AFTER THE MATTRESS SUPPORT BEEN MOVED TO THE
LOWEST LEVEL,MAKE SURE THAT THESE SCREWS ARE TIGHTLY
NOTE:
L1
L2
M
I
A
B
B
A