JARLTECH CCD Series User manual

Bar Code CCD Scan-
ner
Operation Manual
All manuals and user guides at all-guides.com
all-guides.com

This equipment has been tested and found to
comply with the limits for Class A digital device.
Pursant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses, and if
not installed and used in accordance with the
instuctions may cause harmful interference will not
occur in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined by
turning the equipment off and on. The user is
encouraged to try correct interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help. This booklet is available
from the U.S. government Printing Office,
Washington, DC 20402, Stock NO.004-000-
00345-4.
CAUTION: Any changes of modifications not
expressly approved by the grantee of this
device could void the user’s authority to
operate the equipment.
Operation is subject to the following two conditions:
(1) This devive may not cause harmful interference.
(2) This device must accept any interference received
including interference that may cause undesired
operation.
All manuals and user guides at all-guides.com

1
Contents
1. Before You Install ........................................................ 3
2. Installing Keyboard Wedge Interface CCD Scanner .. 5
3. Installing RS232 Interface CCD Scanner.................... 7
4. “Quick Install” Programming...................................11
5. Custom Programming................................................ 15
6. Troubleshooting......................................................... 43
Appendix I: Specifications ............................................. 45
Appendix II: ASCII Code Table..................................... 49
All manuals and user guides at all-guides.com

2
All manuals and user guides at all-guides.com

3
1
•••• • • •
BeforeYou Install
This manual describes functions and
usage of the Series CCD scanner,
including both keyboard wedge and
RS232 interface options.
The CCD scanner designed to
accommodate many application
environments and user requirements.
It may be programmed by scanning
special bar code labels included in
this manual, and may be
reconfigured at any time to meet
future needs and changing applica-
tion requirements. A built-in
memory backup circuit enables the
CCD to retain programmed data
during any power outage.
Step 2: Review packing list
Please ensure that your scanner
shipment is complete.
The keyboard wedge interface CCD
Scanner includes:
•1 pce CCD scanner with keyboard
wedge cable
• 1 pce Operation Manual
By shutting off your computer, you
will prevent any accidental damage
to the CCD scanner and computer.
Step 1: Turn off your computer
All manuals and user guides at all-guides.com

4
The RS232 interface CCD Scanner
includes:
•1 pce CCD scanner with RS232
cable
•1 pce Operation Manual
Before You Install
Step 3: Determine installation mode
If you purchased with a keyboard
wedge interface, turn to Chapter 2
for installation instructions. If you
purchased CCD with an RS232
interface, turn to Chapter 3.
All manuals and user guides at all-guides.com
all-guides.com

5
•••• • • •
2
This chapter describes the procedure
for installing the CCD scanner using
a keyboard wedge interface.
Step 2: Connect to your computer
Connect the keyboard to the female
end of the T-connector of the cable
provided. Plug the male end of the
T-connector into the keyboard port
of your computer.
Review the installation diagram on
the following page.
Step 1: Turn off your computer
If you have not already done so, turn
off your computer to avoid any
accidental damage to the scanner and
your computer.
Installing CCD Scanner
(Keyboard Wedge Interface)
All manuals and user guides at all-guides.com

6
Installing Keyboard Wedge Interface CCD Scanner
Step 3: Turn on your computer
Start up your computer. It should
boot up normally. If a keyboard
error appears, there may be an
incompatibility between the com-
puter and the scanner keyboard type.
The scanner will activate with a
“beep” indicating a successful
installation.
You may now test your scanner by
scanning any bar code. The bar code
number will appear on the screen of
your computer.
Step 4: Turn to Chapter 4
You are now ready to program the
keyboard wedge interface CCD
scanner to meet the specific require-
ments of your application
environment.
All manuals and user guides at all-guides.com

7
•••• • • •
3
This chapter describes the procedure
for installing the CCD scanner using
an RS232 interface.
Step 1: Turn off your computer
If you have not already done so, turn
off your computer to avoid any
accidental damage to the scanner and
computer.
Step 2: Decide on power access
There are 2 models of RS232 CCD
scanner. The first one without DC-
JACK on the cable is named
XXXXR9D of its model. Its connec-
tion requires +5V DC to be input
from the computer directly. Another
one with DC-JACK on the cable is
named XXXXR9R of its model. This
connection requires +8V~+14V DC
to be input from the external adaptor
to the DC JACK or the PIN-9 of
RS232 port of your computer(see
Appendix I page 45). If you are
using the power provided through
your terminal, please see Step 3, If
you are using an external connection,
go to Step 4.
Step 3: Connect to your terminal
Connect the 9-pin femal connector
(DB9F without DC jack) to the male
equivalent (DB9M) port in your
terminal.
Installing CCD Scanner
(RS232 interface)
All manuals and user guides at all-guides.com

8
Installing RS232 Interface CCD Scanner
Step 4: Connect to your computer
Step 5: Turn on your computer
Your computer should boot up
normally. The scanner should
activate with a beep indicating a
successful installation.
Connect the 9-pin female connector
(DB9F with DC jack) to the male
equivalent (DB9M) port on your
computer . Provide power to the DC
jack on the DB9F connector by
using an external adapter (see
Specifications in Appendix I).
Review the installation diagram on
the following page.
All manuals and user guides at all-guides.com