Jaxpety TOBBI User manual

User Manual
Model Number：TH17P0581
www.jaxpety.com
Scan ! To find more surprise!

1 2
www.jaxpety.com www.jaxpety.com
GENERAL WARNING AND CAUTION
RECOMMENDED AGES 3-6YEARS OLD.
NOT INTENDED FOR USE BY CHILD OVER 100LB.
NOT INTENDED FOR COMMERCIAL USE.
PLEASE CONSULT WITH YOUR HILDS PEDIATRICIAN BEFORE USE.
NEVER LEAVE CHILD UNATTENDED WHILE HE/SHE IS USING THIS PRODUCT.
KEEP SMALL UNASSEMBLED PARTS AND PLASTIC BAGS OUT OF CHILDRENS
REACH.DISPOSE OF THE PLASTIC BAGS PROPERLY.
CARE SHOULD BE TAKEN IN UNPACKING AND ASSEMBLY OF THIS PRODUCT.
CHILDREN SHOULD NOT HANDLE PARTS. INCLUDING BATTERIES, OR HELP
IN ASSEMBLY OF THE PRODUCT.
NEVER USE THE PRODUCT NEAR STEPS. STEEP INCLINES, ROADWAYS.
SWIMMING POOLS OR OTHER BODIES OF WATER.
NEVER ALLOW MORE THAN ONE (1) USER AT A TIME.
ALWAYS HAVE CHILD WEAR SHOES WHILE USING THIS PRODUCT.
IF ANY PART OF THIS PRODUCT IS BROKEN, STOP USING IMMEDIATELY.
DO NOT ALLOW CHILDREN TO CLIMB ON THE EQUIPMENT.
USE ONLY AS INTENDED.
WARNING: Never leave child unattended while using this product.
Save these instructions for future reference.
Adult assembly required.
Read all instructions prior to use.
PARTS LIST
Weight Bar Rack
Cross Bar Foam
Foam For Upright
Foam For Rear Bracer
50 OD.X75mm. Bracket Foam
Foam For Weight Bar
Foam For Stopper
Back Rest
Seat
Weight Plate (larger)
Weight Plate (middle)
Weight Plate (smaller)
Upright
Rear Bracer Tube
Bench Frame
Front Floor Tube
Connector Tube
Leg Lift
Cross Bar
Weight Bar
60 mm. Round End Cap
1" Round End Cap
1/2" Round End Cap
Stopper
Lock Pin
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
2
1
1
1
2
1
1
1
6
5
4
1
2
2
2
4
2
2
1
1
1
1
2
3
3
14
15
16
17
18
19
20
21
22
23
24
25
QT Y.DESCRIPTION NO. QTY.DESCRIPTION

4
3
PRODUCT ASSEMBLY
www.jaxpety.com www.jaxpety.com
Insert the Connector Tubes(5) into the Uprights(1) as shown in Figure 1.
Attach them to Rcar Bracer Tube(2) with M8 X 35 Round Head Bol(28).
Use the ScrewDriver(33) to tighten these bolts(28) through the dimpled holes on the
Uprights.
Attach the Front Floor Tube (4) to the Bench Frame (3) with the M8 x75
Round Head Bolt (26)
Assemble the Rear Bracer Tube (2) to the Bench Frame (3) with two
M8 X 35 Round Head Bolts (28) and M8 Nut Caps (31)
Step one:
FIGURE 1
OVERVIEW DRAWING
23
24
25
10
14
5
13
14
5
13
16
16 1
21
22
18
18
20 30
12
3
4
29 29
29
29
2929
29 29
17
10
1
19
8
1
1
2
27
11
15
10
10
25 24 15 11 26 9
9
9
9
16
1
28
28
28
28
17
16
33 34
7
6
31
31
31
9
9
26
27
28
29
30
31
33
34
M8 X 75 Round Head Bolt
M8 X 50 Round Head Bolt
M8 X 35 Round Head Bolt
M6 X 12 Round Head Bolt
4.8 X 16 Tapping Screw
M8 Cap Nut
Screw Driver
Wrench
1
1
4
8
1
3
1
1
NO. QTY.DESCRIPTION
26
4
3
31 2
31
28
5
5
14
14
33
34
2828
28
1
1
Dimpled Dimpled
Dimpled Dimpled
Dimpled
Dimpled
Dimpled

65
PRODUCT ASSEMBLY PRODUCT ASSEMBLY
www.jaxpety.com www.jaxpety.com
Attach Back Rest(21) and Seat(22) to the Bench Frame as shown in Figure 2.
Tighten the M6 X 12 Round Head Bolt(29) using the screwdriver(33).
Step two:
FIGURE 2
Insert the Bracket Foams(18)to the brackets on the Bench Frame(3) as shown in
Figure 3. Fit the Leg Lift(6) into the bracket and fasten by M8X50 Round Head
Bolt(27) with M8 Cap Nut (31).
Insert the Leg Lift(6). Then insert the Cross Bar Foams (15) to the Cross Bar
(7) as shown.
Step three:
FIGURE 3
33
15
15
7
6
3
27
31
18
33 34
18
29
3
22
21
29
29 29 29
29
29
29