Jaypro Sports PBS-10 User manual

1
2
3
4
5
6
8
SEE DETAIL
'A-A'
PLAYER BENCH WITH SHELF
PRODUCT NAME:
JAYPRO
SPORTS
JAYPRO
SPORTS
976 HARTFORD TURNPIKE
WATERFORD, CT 06385 USA
PHONE [phone]
FAX [phone]
WWW.JAYPRO.COM
MODEL. NO:
DRAWN BY: 1/25/2011
PBS-10/PBS-20/PBS-80/PBS-90
J.A. / A.T./M.T.
PLEASE NOTE:
1) FOR SAFE OPERATION AND CONTINUED
HIGH PERFORMANCE FROM THIS
EQUIPMENT, INSPECTION AND
MAINTENANCE MUST BE PERFORMED
BEFORE EACH USE.
2) USE OF THIS EQUIPMENT OTHER THAN
INTENDED MAY BE HAZARDOUS.
3) ALTERATION OR MODIFICATION OF
EQUIPMENT MAY BE HAZARDOUS.
FOR REPAIR OR REPLACEMENT, PLEASE
CALL YOUR DEALER.
DETAIL A-A
DATE:
7A, 7B, 7C OR 7D
9"
78"
CTR TO CTR 78" CTR TO CTR 78" CTR TO CTR
9"
21'-0"
9"
81"
CTR TO CTR 81" CTR TO CTR
9"
9"
78"
CTR TO CTR
9"
9"
76 1/2"
CTR TO CTR 76 1/2" CTR TO CTR 76 1/2" CTR TO CTR 76 1/2" CTR TO CTR
9"
27'-0"
15'-0"
8'-0"

Rev-A 2/2/2011
JAYPRO SPORTS
PLAYER BENCH WITH SHELF PBS-10/PBS-20/PBS-80/PBS-90
LIST OF MATERIALS
PIECE #
PART #
DESCRIPTION
PBS-
10
PBS-
20
PBS-
80
PBS-
90
1
AR5044
BOLT CLIP
32
24
16
40
2
AR5045A
END CAP
8
8
8
8
3
HB5030
5/16”-18 x 3” CARRIAGE BOLT
32
24
16
40
4
HN5046
5/16” FLANGE NUT
32
24
16
40
5
HS5035
#8 ZP PAN HEAD SCREW x ½”
16
16
16
16
6
EP0018
2” x 2” END PLUG
16
12
8
20
7A
AR5111
27’ PLANK
N/A
N/A
N/A
4
7B
AR5052
21’ PLANK
4
N/A
N/A
N/A
7C
AR5053
15’ PLANK
N/A
4
N/A
N/A
7D
AR5079
7.5’ PLANK
N/A
N/A
4
N/A
8
PBS-L
LEG FRAME
4
3
2
5
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED: Phillips Screwdriver Bit With Electric Drill (1),
½” Socket Wrench or Adjustable Wrench (1)
1) Slip the end caps (2) snugly onto each end of each plank (7). Using the electric drill,
assemble a self-drilling screw (5) through the cap and into the flange of the plank. Two
screws are required per end cap. Carefully assemble 2” end caps (6) into bench legs (8).
2) For easiest assembly, position seat plank (7) on a level raised surface such as a desk top,
bleacher seat or work bench. Place the carriage bolt (3) and bolt clips (1) approximately
into place within the slots of the plank. Note that the outside legs should be no more than
8” from the plank edge or 9” from edge to center leg.
3) Position the legs (8) as shown and loosely assemble the hardware illustrated in detail ‘A-
A’. Do not fully tighten the hardware at this time.
4) Stand the unit upright and assemble the backrest plank (7) as illustrated. Level the bench
and make sure the legs are adequately spaced apart. Tighten all fasteners fully.