JCA Collective 42912040 User manual

8FT（244cm) TRAMPOLINE AND
ENCLOSURE OWNER'S MANUAL
KEYCODE:42912040
product
Maximum weight of the user shall NOT exceed 165 lbs/75 kg for this product.
CUSTOMER SERVICE:
!

PRODUCT WARRANTY
CUSTOMER SERVICE
0.
0
(QFORVXUHV\VWHPVDUHGHVLJQHGWRSUHYHQWXVHUVIDOOLQJRIIWKHWUDPSROLQH'RQRWDOORZXVHUVWRLQWHQWLRQDOO\
ERXQFHWRZDUGRURIIWKHEDUULHUDVWKLVFDQXQEDODQFHWKHWUDPSROLQHDQGFRQWLQXDOLPSDFWPD\GDPDJHWKHHQFORVXUH
)RFXV\RXUH\HVRPWKHHGJHRIWKHWUDPSROLQH7KLVZLOOKHOSFRQWURO\RXUERXQFH
6WRS\RXUERXQFHE\IOH[LQJ\RXUNQHHVDV\RXUIHHWFRPHLQFRQWDFWZLWKWKHWUDPSROLQHEHG
/HDUQWKLVVNLOOEHIRUH\RXDWWHPSWDQ\RWKHUV
$YRLGERXQFLQJWRRKLJK6WD\ORZXQWLOO\RXFDQFRQWURO\RXUERXQFHDQGUHSHDWHGO\ODQGLQWKHFHQWUHRIWKHWUDPSROLQH
'RQRWERXQFHLPPHGLDWHO\DIWHUDPHDO

It is important that children are not involved in the assembly
of the trampoline.

Ensure any pads (where they are required) covering the frame/suspension system are securely attached at all times.
Enesure the enclosure is securely attached and in good condition at all times.
Make sure that the area around, underneath and above the trampoline is clear of objects that could interfere with
the person jumping. Do not allow children,pets,toys or other play equipment to be present under the trampoline.
Adults should model safe use of trampolines when children are present.
Remove shoes as they may damage the bed and increase trhe risk of injury.
Children should be educated by responsible adults to always climb on and off the trampoline,and never jump or bounce off.
It is dangerous practice to jump or bounce from the trampoline when dismounting.Never use springs or suspension
elements as hand grips’when getting on and off the trampoline.For further information of additional instructional
material, contact the manufacturer or retailer.To learn more advanced trampolining skills contact a suitable
gymnastics/trampoline club.

(a) Place the trampoline on a flat level surface with impact attenuating properties such
as grass and ensure that it is sufficiently stable to prevent it from tipping over and/or
blowing away. Sandbags or pegs may be suitable anchorage devices.
f

8
NO. Diagram Description
Top rail
Bracket without welding
Bracket with welding
Quantity
A 6
3
3
3
6
1
1
48
1
3
3
3
B
C
D
E
F
G
H
I
J
K
L
Horizontal Leg
Bend Leg
Mat
Frame Pad
Spring
Enclosure net
Steel top rim
Upper Enclosure pole
Lower Enclosure pole

9
Hexagon wrench（M4）
Hexagon wrench(M5)
NO. Diagram Description Quantity
3
3
6
1
1
1
1
1
1
6
M
N
O
P
Q
R
S
T
U
V
Screw for plastic
connector
Plastic
connector
Screw for Leg
Spring tool
Wrench
Enclosure net tie
down strap
Needle for Enclosure net tie
down strap
Leg to Frame
hardware

10
1.Connect the Top rail（A)with the Bracket without welding(B）together as below picture show,repeat
3 times, pay attaention to the direction
A x3 B x3
A x3 C x3
A
B
2.Connect the Top rail（A)with the Bracket with welding(C）together as below picture show,
repeat 3 times,pay attaention to the direction

11
3.Connect the finished parts of step 1and step 2 together as below pictures show,
pay attention to the direction
4.Connect the Horizonal Leg（D）and the Bend Leg （E）together，then secure it use the screw
for Leg(O) as below picture picture show
O x6
D x3
E x6
D
E
E

12
5.Connect the finished parts of step 3 and the finished parts of step 4 together as below picture show
6.Use the Leg to Frame hardware(V)to connect the Bend Leg（E）and the Bracket without welding(B),
Bracket with welding(C) as below picture show
V x6

13
7.Turn over the finished parts of Step 6 and connect as below picture one by one.

8.
Warning!
When attaching the springs, do not place your hands,
arms, legs or any other body part close to the connector
points(i.e. joints connecting the steel tubes).The connector
points can become pinch points as the trampoline springs
tighten up. Wear heavy duty working gloves to protect
your hands from pinching by the springs and protective
goggles to avoid injuries to the eyes. Be steady when
installing the springs as it can rebound and fly off if you
inadvertently let go when not hooked properly. Make sure
no children are playing nearby when installing or assisting
in the assembly of the trampoline.
Starting at the point "Zero" hook one end of the spring(H) into the triangle-ring
on the mat(F).Holding the spring tool(P) underhand, pull the other end of the
spring and lock it into the hole on the frame as shown below
.
After you have secured the spring at point "Zero", place another spring at the
opposite place and then divide into two parts again with another two springs
at three and nine o' clock position.
Attach the springs in the same manner as the previous step.
Then follow 1,2 ,3 process to get spring finished assembly.
The number of triangle-rings sewn onto the mat is equal to the number of holes
on the frame. If you notice that you have miscounted a hole or triangle-ring,
remove and reinstall the springs as necessary while maintaining an even
distribution of tension as explained above.
14

15
H*48pcs
!
Please pay
attention to the end
shape of the spring
connect to the top rail
The curved hook end
!
connected to the
triangle -ring.
The first hole
!

16
9.Put the Lower enclosure pole (L)into the Bracket with welding(C) as below picture show,
please pay attention that the clip must be pulled out
10.Put the Frame Pad(G)on the Mat(F),pay attention that the opening of the pad aligned with the Lower
Enclosure pole(L)
L x3
G x1

17
11.Connect the steel top rim(J) with the Enclosure net(I)top rim tunnel as below picture show
12.Connect the steel top rim (J) with the Plastic connector（N）by Screw(M)，then put the
Plastic connector(N) into the Upper Enclosure pole(K),please make sure the clip must be pulled out.
I x1
J x3
K x3 M x3 N x3
M

18
13.Connect the finished part of Step 12 and the Lower enclosure pole (L) as below picture show
14.Put up the Pad(G), connect the Enclosure net and the Mat(F) by the needle(T) and the Enclosure net
tie down strap (U) as below picture show
T x1
U x1

19
15.After finishing the Enclosure net assembly,please put down the Pad , tighten the elastic strap on
the pad (G) and the traiangle ring on the Mat(F) together to fasten them.

20