JCA Collective 43062706 User manual

TRAMPOLINE 12FT
RECTANGULAR WITH ENCLOSURE
KEYCODE:43062706
Name: JCA Collective Email: [email protected]
Phone Number: [phone] Oce Hours: Monday to Friday 9am to 5pm
CUSTOMER SERVICE:
ATTENTION!
SAFETY INFORMATION, INSTALLATION, CARE
AND MAINTENANCE INSTRUCTIONS.
READ PRIOR TO ASSEMBLING AND USING THE TRAMPOLINE

PRODUCT WARRANTY
CUSTOMER SERVICE
0.
8 - 23
24 - 25
27 - 28
26
29
29
30
31
WARNING! Trampoline is not allowed for children under six years of age.

It is important that children are not involved in the assembly
of the trampoline.

(a) Place the trampoline on a flat level surface with impact attenuating properties such
as grass and ensure that it is sufficiently stable to prevent it from tipping over and/or
blowing away. Sandbags or pegs may be suitable anchorage devices.
f

76
4
2
1-A
1-B
8
4
3
8
1
4
5
6-A
6-B
7
2
2
4
Curved Top Rail 1-A
Curved Top Rail 1-B
Straight Top Rail
Bracket with welding
Key Number Diagram Description Quantity
8
Long Spring 6-A
Short Spring 6-B
Mat
Leg
Leg Extension

1
1
8
8
1
4
4
8
8
9
10
11
12
13-A
13-B
14
Key Number Diagram Description Quantity
9
Frame Pad
Enclosure net
Enclosure net tie down
strap with needle
Lower enclosure pole
Upper enclosure pole
Short Steel Top Rim 13-A
Short Steel Top Rim 13-A
Plastic connector
with screw & spacer
Long

REMEMBER TO USE GLOVES DURING ASSEMBLY TO AVOID PINCHING.
AT LEAST 2 PEOPLE ARE REQUIRED TO ASSEMBLE THE TRAMPOLINE AND ENCLOSURE
ALWAYS WEAR PROTECTIVE GLOVES TO PROTECT AGAINST INJURY AS TRAMPOLINE
AND ENCLOSURE ARE HEAVY EQUIPMENT.
1
1
2
2
4
1
15
16
17
18
19
20
Key Number Diagram Description Quantity
Spring tool
Spanner
Horizontal ladder tube
Vertical ladder tube
M6x55mm screw with nut
Hexagon wrench
10

Step 1:Leg support Assembly
BEFORE YOU BEGIN: Review all steps before assembly and read all precautions before
using the trampoline.
At least two adults are required to assemble this trampoline. Protective gloves should be
used during assembly to avoid pinching by the springs.
Connect the two leg extensions(5) with leg base(4) as shows in figure 1.
Repeat these steps for all legs.
Warning: Make sure that you have plenty of space and a clean,dry area suitable for
assembing this trampoline
IT IS ESSENTIAL THAT THE INTENDED SITE FOR THIS TRAMPOLINE IS COM-
PLETELY FLAT AND LEVEL.
11
Figure 1
5
4

Step 2：FrameAssembly
Pick up top rail(1-A),connect both ends with bracket with welding(3),and pick up
top rail (1-B),connect both ends with bracket with welding(3) as figure 2 shows
Repeat this step with all top rails as figure 2 shows.
12
Connect bracket with welding(3)with left leg extension(5).
Repeat this step for all legs assembly as figure 3 shows.
Connect the straight top rail(2)to the bracket with welding(3)and repeat this 2 times
for each top rail to finish frame assembly as Figure 4 shows.
3
1-A 1-B
Figure 2

1-B
Figure 3
Figure 4
13
1-A
1-B
1-B
1-A
1-A
2
1-B
1-B
2
2
2

14
2
2
2
2

Step 3: Spring Assembly
Warning!
When attaching the springs, do not place your hands,
arms, legs or any other body part close to the connector
points(i.e. joints connecting the steel tubes).The connector
points can become pinch points as the trampoline springs
tighten up. Wear heavy duty working gloves to protect
your hands from pinching by the springs and protective
goggles to avoid injuries to the eyes. Be steady when
installing the springs as it can rebound and fly off if you
inadvertently let go when not hooked properly. Make sure
no children are playing nearby when installing or assisting
in the assembly of the trampoline.
Starting from the 8pcs of right & left springs next to corner springs, hook one end of
the spring(6-A) into the triangle-ring on the mat(7). Holding the spring tool(16) in hands,
pull the other end of the spring and lock it into the hole on the frame as shown in figure 5.
After you have secured the 8pcs of right & left springs next to corner springs, place
one spring at the middle hole on each of four straight top rails, hook one end of
the spring(6-A) into the triangle-ring on the mat(7). Holding the spring tool(16) in hands,
pull the other end of the spring and lock it into the hole on the frame as shown in figure 5.
Attach the rest of the springs in the same manner as the previous steps until remove all
springs are assembley. Please note 4pcs of corner springs should be 6-B, and the rest
are 6-A.
The number of triangle-rings sewn onto the mat is equal to the number of holes
on the frame. If you notice that you have miscounted a hole or triangle-ring,
remove and reinstall the springs as necessary while maintaining an even
distribution of tension as explained above.
15

7
16
6-B 6-B
6-B
6-B
6-A
6-A
6-A
Figure 5

The curved hook end
connected to the
triangle -ring.
!
Please pay
attention to the end
shape of the spring
connected to the top
rail
!
Eye glasses are not
provided in this product

Step 4 Lower Enclosure Pole Assembly
Connect lower enclosure pole(11) with bracket with welding(3)by clipping the pin.
Repeat this 8 times as figure 6 shows to finish lower enclosure pile assembly.
17
After assembly,please make sure the pit pin is protuberant from the hole.
11
Figure 6
B

18
Step 5: Upper enclosure pole & safety net & top rim assembly
The direction of the upper enclosure pole must follow
below diagram.
Figure 8
Connect the lower enclosure pole(11)and the upper enclosure pole(12)by putting the
pit pin as Figure 9 shows
.
Let the whole steel top rim (13-A and 13-B) go through the tunnel on top of the enclosure net (9),
then connect two adjacent steel top rim ends with plastic connector (14).
Line up the hole in the steel top rim(13-A and 13-B)and screw together ensuring the screw (14)also
goes through the hole in the steel top rim.
Repeat for the remaining steel top rims and plastic connectors as Figure 8 shows.
Once complete, lift the steel top rim to the top of the upper enclosure poles (12)and plug the
steel top rim connector into the hole of the upper enclosure pole until the locking pins click in place.
14
12
13-A
14
13-B
A
Connect cord with needle as figure 11 shows and repeat process 1,2 and 3.

19
Figure 9
Figure 10
11
12
12
11
B
A

20
Figure 11
3