Jeda Wireless Pad User manual

12V
MANUAL
FOR FAST CHARGING OR EXTRA PORTS
TESLA MODEL 3 AND Y :  GUIDE FOR UTILIZING THE 12V SOCKET 

REQUIRED
ITEMS
3 - 4 foot long Micro USB to USB A
cables ( 3 . 3 is avg .)
Q . C 3 . 0 Adapter with two USB
ports *
Jeda Wireless Pad
Torx 20 screwdriver / bit
Fast charging compatible phone *
To use the 12v socket , you will need
the following items :
12V SOCKET
*Be sure the QC adapter is fast charging
capable. We recommend a known brand.
*Fast charging is limited to certain phone types/models.
This method can still be done if you'd like to clear up the
front USB ports.

The first thing you will need to do is
remove the panel in your Model 3 .
Removing the panel is easy to do , and
does not damage your vehicle . There
are many online videos which
demonstrate how to safely remove the
panel in question .
p h o t o c o u r t e s y : P i x c e l s , T e s l a t i n o Y o u t u b e C h a n n e l
SETUP

Once the panel is removed , you  are going to
have to unscrew the bolts to remove the
cover . A torx 20 head is required for removal .
You can use a dremel , or a manual
screwdriver for the process .
Once all the screws have been removed ,
safely place them into an area for
safekeeping . Remove the metal trim below
the screws and place to the side . Remove
plastic bumpers and place to the side .
p h o t o c o u r t e s y : E V N e t w o r k Y o u t u b e C h a n n e l , T e s l a t i n o Y o u t u b e C h a n n e l
SETUP

To get the cables to go under the trim , you
will need to cut down / drill a small opening
for the cable to pass through near the very
front of the trim .
SETUP
p h o t o c o u r t e s y : T e s l a t i n o Y o u t u b e C h a n n e l
Doing so will allow the cables to pass
through the side of the trim from the
front all the way down to the 12v socket .

Run the long ( 3 - 4ft ) USB A to Micro USB
Cables along the side trim all the way to
the rear socket . You can use tape to secure
the cables down .
Once you reach the center console
organizer you will need to run the cables
underneath the center console area , as
seen in the above photo .
After all of the cables have been securely placed , insert the QC 3 . 0 Double USB A
Adapter of your choice into the 12v socket .
SETUP
p h o t o c o u r t e s y : T e s l a t i n o Y o u t u b e C h a n n e l

SETUP
COMPLETE
Once the cables are in place , make sure the
Jeda Wireless Pad is connected and
working properly . After verifying this ,
replace the plastic bumpers , metal trim ,
screws , and original plastic trim . Happy
charging .
Acustomer did create a non-drill guide to the
12v socket, however this has not been done by
our team. You can find the information and link
to that guide in the index.
p h o t o c o u r t e s y : J e d a P r o d u c t s , T e s l a t i n o Y o u t u b e C h a n n e l

I N D E X
Sources:
Teslatino Jeda Wireless Pad 12v install:
https://www.youtube.com/watch?v=73KdINPQCgI
EV Network 12v Socket Install:
https://www.youtube.com/watch?v=HWCYoLTjGi0
Non drill guide guide:
https://www.reddit.com/r/teslamotors/comments/dyotbl/h
ow_to_guide_fast_wireless_phone_charging_in_a/