Jefferson JEFFES22M-110 User manual

JEFFES22M-110
ES 22M FESTOON LIGHT KIT
USER GUIDE
v.1.1
www.jeffersontools.com
INTRODUCTION
This Festoon lighting kit uses the latest in LED technology for long
lasting performance and features a 22M hanging light chain, complete
with 10x holders, ES bulb ttings and guards. The lights are fully
insulated, IP44 rated and suitable for both indoor and outdoor use.
FEATURES:
• Tough, replaceable, polycarbonate 10W LED bulbs equivalent
to standard 60W GLS bulbs (100W / 8000 Lumens combined
lighting power)
• LED bulbs provide longer lasting performance with up to 30,000
hours compared to 2,000 hours with traditional GLS 60W bulbs
• Electrically moulded ES ttings (E27 Edison Screw)
• IP44 rating
KIT CONTENTS:
• 10x 10W LED Light Bulbs [A]
• 10x Bulb wire guards [B]
• 1x 22m of 2mm cable tted with a BS EN 60309 Coupler and
16A plug (110V~50Hz) [C]
SPECIFICATIONS
Supply Voltage: 110V
Frequency: 50Hz
Plug / Socket : 16A 110V BS EN 60309
Cable: 22M H05VV-F PVC 110V (2 x 2mm²)
Insulation: IP44
Operating Temperature: -25°C - 45°C
Illumination: 240°
Colour Temperature: 6500K
Light Emmision: 100W - 8000 Lumens
Warning: This festoon lighting kit only operates
from a 110V~50Hz supply. Contact a qualied
electrician for advice on any issues relating to
electrical safety in your working environment prior
to use.
Information on Disposal for Users of Waste Electrical &
Electronic Equipment (WEEE)
This symbol on the product(s) and / or
accompanying documents means that used
electrical and electronic products should not be
mixed with general household waste.
For proper treatment, recovery and recycling,
please take this product(s) to designated collection
points where it will be accepted free of charge.
SAFETY GUIDELINES
Important: Please read all information carefully
before use and keep these instructions in a safe
place for future reference.
Ensure that you check the equipment thoroughly to ensure it is safe
and t for purpose before each use. It is important that you inspect
all plugs, sockets, power cables and electrical ttings for wear and
damage and repair or replace any defective components. Ensure that
the power cable is kept away from heat, oil and sharp edges.
The risk of electric shock can be minimised by the correct use of the
appropriate electrical safety devices. We recommend that you t a
Residual Current Circuit Breaker (RCCB) in the main distribution
board and that a Residual Current Device (RCD) is used when
operating this equipment.
The Electricity at Work Act 1989 includes legislation that places
legal implications on employers to ensure the safety of electrical
devices in the workplace. The regulations dictate that all portable
equipment must be inspected regularly and tested to ensure that it is
safe for use. ‘Portable equipment’ means any electrical item that can
be moved and this is often referred to as Portable Appliance Testing
(PAT). PAT testing should be carried out regularly on this equipment
by trained, authorised personnel, as required by the legislation.
The Health and Safety at Work Act 1974 states that it is the
responsibility of the owner of electrical appliances to ensure that both
the equipment and working environments are maintained to ensure
safe operation at all times.
Ensure that the power supply matches voltage requirements specied
on the equipment and that the plug is wired correctly and tted with
the correct fuse. If the electrical fuse blows, ensure it is replaced by
an identical type of fuse with the same rating.
Do not operate or connect to the electrical supply when the cable is in
a coil. Follow installation instructions prior to connecting to the sup-
ply. Disconnect from the power supply before replacing the LED bulbs
or making any adjustments to the position of the chain.
Allow the LED bulbs to cool before removing or disconnecting. Ensure
equipment is well-maintained and checked for damage before use.
Do not use if the equipment is damaged. Contact your nearest Jef-
ferson Dealer for advice on parts and repair.
INSTALLATION
1. Prior to connecting to a power supply, secure the bulb guards to
the E27 Edison Screw Fittings, using the hooks on the guards to x to
the cable.
2. Carefully screw in each LED bulb, ensuring a secure t.
3. Hang the festoon light chain in a suitable location ensuring that
they are adequately supported and prevent straining of the cable.
The rst bulb holder module should be positioned to provide
adequate cable length to the supply point and should be suitably
secured.
4. Where possible, each bulb module should be screwed in position
using the xing holes supplied (cable ties can be used to secure each
module if screws are impractical in your working environment).
5. Connect the 16A plug to a 110V AC supply and turn the power
supply on.
6. Check that all of the bulbs are functioning correctly (replace any
broken bulbs as required).
[A] [B] [C]

LIMITED WARRANTY STATEMENT
Jefferson Professional Tools & Equipment, or hereafter "Jefferson" warrants its customers that
its products will be free of defects in workmanship or material. Jefferson shall, upon suitable
notication, correct any defects, by repair or replacement, of any parts or components of this
product that are determined by Jefferson to be faulty or defective.
This warranty is void if the equipment has been subjected to improper installation, storage,
alteration, abnormal operations, improper care, service or repair.
Warranty Period
Jefferson will assume both the parts and labour expense of correcting defects during the
stated warranty periods below.
All warranty periods start from the date of purchase from an authorised Jefferson dealer. If
proof of purchase is unavailable from the end user, then the date of purchase will be deemed to
be 3 months after the initial sale to the distributor.
1 Year
• Jefferson ES 22M Festoon Light Kit [JEFFES22M-110]
90 Days
• All replacement parts purchased outside of the warranty period
Important: All parts used in the repair or replacement of warranty covered equipment will be
subject to a minimum of 90 days cover or the remaining duration of the warranty period from
the original date of purchase.
Warranty Registration / Activation
You can register and activate your warranty by visiting the Jefferson Tools website using the
following address:
www.jeffersontools.com/warranty and completing the online form.
Online warranty registration is recommended as it eliminates the need to provide proof of
purchase should a warranty claim be necessary.
Warranty Repair
Should Jefferson confirm the existence of any defect covered by this warranty the defect will
be corrected by repair or replacement at an authorized Jefferson dealer or repair centre.
Packaging & Freight Costs
The customer is responsible for the packaging of the equipment and making it ready for
collection. Jefferson will arrange collection and transportation of any equipment returned under
warranty. Upon inspection of the equipment, if no defect can be found or the equipment is not
covered under the terms of the Jefferson warranty, the customer will be liable for any labour
and return transportation costs incurred. These costs will be agreed with the customer before
the machine is returned.
NOTE: * Jefferson reserve the right to void any warranty for damages identified as being
caused through misuse *
Warranty Limitations
Jefferson will not accept responsibility or liability for repairs made by unauthorised technicians
or engineers. Jefferson's liability under this warranty will not exceed the cost of correcting the
defect of the Jefferson products.
Jefferson will not be liable for incidental or consequential damages (such as loss of business
or hire of substitute equipment etc.) caused by the defect or the time involved to correct the
defect. This written warranty is the only express warranty provided by Jefferson with respect to
its products.
Any warranties of merchantability are limited to the duration of this limited warranty for the
equipment involved.
Claiming Warranty Coverage
The end user must contact Jefferson Professional Tools & Equipment:
(Tel: [phone]) or their nearest authorised Jefferson dealer where final
determination of the warranty coverage can be ascertained.
Step 1 - Reporting the Defect
Online Method:
Visit our website www.jeffersontools.com/warranty and complete the Warranty Returns form.
You can complete the form online and submit it to us directly or download the form to print out
and return by post.
Telephone Method:
Contact your Jefferson dealer or sales representative with the following information:
• Model number
• Serial number (usually located on the specification plate)
• Date of purchase
A Warranty Returns form will be sent to you for completion and return by post or fax, together
with details of your nearest authorised Jefferson repair centre. On receipt of this form Jefferson
will arrange to collect the equipment from you at the earliest convenience.
Step 2 - Returning the Equipment
It is the customer’s responsibility to ensure that the equipment is appropriately and securely
packaged for collection, together with a copy of the original proof of purchase. Please note
that Jefferson cannot assume any responsibility for any damage incurred to equipment during
transit. Any claims against a third party courier will be dealt with under the terms & conditions
of their road haulage association directives.
NOTE: Jefferson will be unable to collect or process any warranty requests without a copy of
the original proof of purchase.
Step 3 - Assessment and Repair
On receipt, the equipment will be assessed by an authorised Jefferson engineer and it will
be determined if the equipment is defective and in need of repair and any repairs needed are
covered by the warranty policy. In order to qualify for warranty cover all equipment presented
must have been used, serviced and maintained as instructed in the user manual.
Where repair is not covered by the warranty a quotation for repair, labour costs and return
delivery will be sent to the customer (normally within 7 working days). Note: If the repair
quotation is not accepted Jefferson Professional Tools & Equipment will invoice 1 hour labour
time at £30 per hour plus return carriage costs (plus VAT).
In cases where no fault can be found with the equipment, or, if incorrect operation of the
equipment is identified as the cause of the problem, a minimum of 1 hour labour at £30 per
hour plus carriage costs will be required before the equipment will be despatched back to the
customer.
Any equipment repaired or replaced under warranty will normally be ready for shipment back to
the customer within 7 working days upon receipt of the equipment at an authorised Jefferson
Repair centre (subject to part availability). Where parts are not immediately available Jefferson
will contact you with a revised date for completion of the repair.
General Warranty Enquiries
For any further information relating to Jefferson warranty cover please call:
[phone] or send your enquiry via email to [email protected]
Disclaimer:
The information in this document is to the best of our knowledge true and accurate, but all
recommendations or suggestions are made without guarantee. Since the conditions of use are
beyond their control, Jefferson Tools® disclaim any liability for loss or damage suffered from
the use of this data or suggestions. Furthermore, no liability is accepted if use of any product
in accordance with this data or suggestions infringes any patent. Jefferson Tools® reserve the
right to change product specifications and warranty statements without further notification. All
images are for illustration purposes only.
EC Declaration of Conformity Name and address of manufacturer or
authorised representative:
Jefferson Tools,
Herons Way,
Chester Business Park,
Chester,
ed Kingdom,
CH4 9QR
We, Jefferson Professional Tools & Equipment, as the authorised European Community representative of the manufacturer,
declare that this equipment conforms to the requirements of the following Directives:
* Electromagnetic Compatibility 2014/30/EU (as amended)
* Restriction of Use of Hazardous Substances (ROHS) 2011/65/EU (as amended)
Signed by: Stephen McIntyre (Operations Director)
Date: 19.06.19 Tel. [phone] Email: [email protected]
www.jeffersontools.com
JEFFES22M-110
ES 22M FESTOON LIGHT KIT
USER GUIDE
v.1.1
2011/65/EU
RoHS