Revolution Micro Avici V User manual

240v, 277v, 347v or 480v
Avici V Integrated LED Lighting System
Owner's Manual May 18, 2022
The Box Contains
Avici V Integrated LED Lighting System
Power Cords
Custom Lighting Hangers
Congratulations on your new Avici. The Avici combines an array of
Osram LEDs with our custom-designed drivers for one amazing,
programmable spectrum, computer-controlled grow lighting system.
This manual will tell you how to hang, connect and operate your new Avici.
404/[e-mail]
Installing The V Series
To assemble a light in the
V Series, you will need a
4.5mm Allen wrench.
Screw the red hanger
onto the metal tab on
the front and back of
the Avici V Bars.
SCREWS
1.
2.
The bars need to be arranged in the following pattern so the
power flows through one bar to the next. The ends of the bar
are labeled either IN or OUT, and should be alternated with
consideration for how it will be wired.
3.
IN
IN
IN
IN
OUT OUT
OUT OUT

404/[e-mail]
5.
Finished Assembly
4.
MOUNTING HOLE
MOUNTING HOLE
Attach the top of the wire rack to the location within racking system
or ceiling, and the ends to the mounting holes shown below.
Powering Up
Remove the protective cap from the power socket.
1.
Ensure you can plug the lights in with the IN - OUT pattern
described in the previous section.
2.
Installing The V Series Continued
Align the sections on the
socket with those on the
power cable. They’ll only
fit together one way.
Push the cable into the
socket until it won’t go
any further.
Rotate the locking ring until it begins
to thread onto the socket. Continue
to push the plug into the socket until
it is rmly plugged in, and tighten the
locking ring.
Attach cable to power supply to the RLC1.
LOCKING RING
3.
4.
5.
6.
7.
Repeat on the remaining 3 bars.
Please see RLC-1 Manual for Communications Instructions.
8.

404/[e-mail]
Blinks Once A Second – Over Temperature
If the Avici internal heatsink reaches a programmed over
temperature point, it's way too hot and it will shut o with the
OFF LED blinking on and o once a second. Once the internal
temperature cools to 10 degrees below the over temp point, the
Avici will automatically restart.
Blinks Four Times A Second – Over Voltage / Under Voltage
If supplied power is outside safe operating range for the Avici, the
LED will ash quickly to let you know the xture is working but not
going to come on.
If the status LED is ashing quickly you can either remove and reapply
power, but best to check the electrical supply rst. Incorrect sup-
ply voltage can destroy the xture. Avici normal voltage range is
100v-300v and must be stable for 10 seconds to power up.
Flickers Briey Once a Second – External Control
The RLC1 and TouchMi Room Controller can control 512 Revolution
lights in two zones. You can set on and o times, sunrise and sunset
ramps, dimming with temperature and over temperature shutdown
for each zone for lights that support these commands. Avici also
accepts commands for color mixing for custom spectra. Please see
the RLC1 and TouchMi manuals for details on controlling the output
spectrum.
When the provided RJ-14 phone cable is plugged into the Avici and
a Revolution controller, the front panel LED will blink o, very briey,
once a second to show you that Avici is controlled by an outside
source and that communication is up and running.
If the cable becomes disconnected, Avici will maintain chosen power
level and spectrum – just as you would expect. After a power failure,
Avici returns to full power and spectrum if not commanded otherwise
by a controller.
Blinking LEDs
What Your Avici Is Telling You
We’re Here to Help.
We’d be happy to answer any questions or help you through the installation.
Call us: 404 - 334 - 9788