Jensen VM8013HD - Screen MultiMedia Receiver User manual

VM8013HD
Installation and Operation Manual
Instrucciones de la Instalaci6n y de la Operaci6n
Instructions d'installation et d'operation
160 .....
r rii

VM8023HD <Ey~!5>
TABLE OF CONTENTS
Introduction 1
Installation 1
Wiring 3
Front Panel Release 4
Remote Control Operation 5
Remote Control Functions 6
Operation 7
Satellite Radio Operation 10
Radio Operation
12
DISCIMP3IVVtv1A Playback : 14
Controlling Your iPod 18
Setup Menu 19
Care and Maintenance 20
Troubleshooting
21
Specifications 22
CONTENIDO
Introducci6n 23
Instalaci6n 23
Cableado 25
Liberaci6n del Panel Frontal 26
Operaci6n de Control Remoto 27
Funciones de Control Remoto 28
Operaci6n 30
Operaci6n de Radio Satelital 33
Operaci6n de Radio 35
Reproducci6n
de DISCOIMP3IWMA 37
Como controlar Su iPod 42
Menu de Configuraci6n 43
Cuidado yMantenimiento 44
Resoluci6n de Problemas .45
Especificaciones 46
TABLE DES MATI~RES
Introduction 47
Installation 47
Cablage 49
Relachment
du panneau d'avant 50
Operation telecommande
51
Fonctions atelecommande 52
Operation 54
Operation radio satellite 57
Operation radio 59
Reproduction DISCIMP3IWMA
61
Commandervotre iPod 66
Menu configuration 67
Soin et maintenance 68
Depannage 69
Specifications 70

VM8013HD ~~ES>
HD RadioTM Technology Manufactured Under Ucense From iBiquity Digital
Corporation. U.S. and Foreign Patents.
HD Radio™ and the HD and HD
Radio logos are proprietary trademarks of iBiquity Digital Corporation.
INTRODUCTION
Congratulations on your purchase of the Jensen VM8013HD Mobile
Multimedia Receiver. It's agood idea to read all
of the instructions before
beginning the installation. We recommend having your Jensen
VM8013HD
installed by areputable installation shop.
INSTALLATION
This unit is designed for installation in cars, trucks and vans with an existing
radio opening. In many cases, aspecial installation kit will be required to
mount the radio
to the dashboard. These kits are available at electronics
supply stores and car stereo specialty shops. Always check the kit
application before purchasing to make sure the kit works with your vehicle.
If you have trouble locating akit or need installation assistance, contact
Technical Support at 1-800-323-4815 from 9:00am to
6:00pm EST Monday
through Friday.
Tools and Supplies
The following tools and supplies are needed to install the radio:
Torx type, flathead and Philips screwdrivers
Wire cutters and strippers
Tools to remove existing radio (screwdriver, socket wrench set
or other
tools)
Electrical tape
Crimping tool
Volt meterltest light
Crimp connections
18
gauge wire for power connections
16-18 gauge speakerwire
Preparation
1. Disconnect Battery
Before you begin, always disconnect the battery negative terminal.
NOTE:
If the VM8013HD is to be installed in a car equipped with an on-
board drive or navigation computer, do not disconnect the battery
cable. If the cable is disconnected, the computer memory may be lost.
Under these conditions, use extra caution during installation to avoid
causing a short circuit.
1
2. Remove Transport Screws
~ -----::7" TRANSPORT SCREWS
HALF SLEEVE
3. Remove Radio from Sleeve
Slide the mounting sleeve offthe chassis. If it is locked into position,
use the removal tools (supplied) to disengage it.
Mounting Sleeve Installation
1. Check the dashboard opening size by sliding the mounting sleeve into
it.
[ )1
1'-"~---------=--=--=--=--1-83-mm- -- -- --- -- -- -- --~+.r-
If the opening is too small, carefully cut or file as necessary until the
sleeve easily slides into the opening. Do not force the sleeve into the'
opening or cause
it to bend or bow. Check for sufficient space behind
the dashboard for the radio chassis.
2. Locate the series of bend tabs along the top, bottom, and sides of the
mounting sleeve. With the sleeve fully inserted into the dashboard
opening, bend as many of the tabs outward as necessary to firmly
secure the sleeve to the dashboard.
CAUTION:
For proper operation of the DVD player, the chassis must
be mounted within 20° of horizontal. Make sure the unit is mounted
within this limitation.
3. Place the radio in front of the dashboard opening so the wiring can be
brought through the mounting sleeve. Follow the wiring diagram

<li~s.!'S> VM8013HD
Kit Installation
If your vehicle requires the use of an installation kit to mount this radio,
follow
the instructions included with the installation kit to attach the radio to
the mounting plate supplied with the kit.
1. Wire and test the radio as outlined in the Mounting Sleeve Installation
instructions.
2. Install
the radio/mounting plate assembly to the sub-dashboard
according to the instructions in the installation kit.
3.
Replace the dashboard trim panel.
r;~~~:~~~o;,:,;,
--..::::::-=- ~: li
--..;;:;:---- :11
~ ; II
n
i
ISO Installation
This unit has threaded holes in the chassis
side panels which may be used with the
original factory mounting brackets of some
vehicles to mount the radio to the
dashboard. Please consult with your local
car stereo shop for assistance on this type
of installation.
1. Remove the existing factory radio
from the dashboard or center console
mounting. Save all hardware and
brackets
as they will be used to mount the new radio.
2. Carefully
unsnap the plastic frame from the front of the new radio
chassis.
Remove and discard the frame.
3.
Remove the factory mounting brackets and hardware from the existing
radio and attach
them to the new radio. Do not exceed M5 x 9mm
maximum screw size. Longer screws may damage components inside
the chassis.
4.
Wire the new radio as outlined in the Mounting Sleeve Installation
instructions.
5.
Mount the new radio assembly to the dashboard or center console
using the reverse procedure of step 1.
Fuses
When replacing afuse, make sure the new fuse is the correct type and
amperage. Using an incorrect fuse could damage the radio.
Reconnect Battery
When wiring is complete, reconnect the battery negative terminal.
Removing the Radio
To remove the radio after installation, first
remove the face plate. Next, remove the trim
ring by firmly grasping one side and pulling.
Insert the removal keys straight back until
they lock, then pull the radio out. If the
removal keys are inserted at an angle, they
will not lock properly and will not release the
unit.
SPRING CLIP (*l
-i------ TRIM RING
5.
carefully and make certain all connections are secure and insulated
with wire nuts or electrical tape. See "Wiring" on page 3. After
completing the wiring connections, turn the unit on to confirm operation
(vehicle ignition must be on). If the unit does not operate, re-check all
wiring until
the problem is corrected.
4.
Make sure the radio is right-side up, then
carefully slide the radio into the mounting
sleeve until it is fully seated and the spring clips
lock it into place.
Secure the rear of the unit to the car body
using
the mounting bolt and rubber cushion.
6. Test
the radio using the "Operation"
instructions
that follow.
Technical Assistance
If you require assistance, contact Technical Support at 1-800-323-4815
from 9:00am to 6:00pm EST Monday through Friday.
2

VM8013HD < 'I' ',1 l'
WIRING
NOTE: The ampllflel'ln thl. radio I. only designed for u.e with four
speakers. Nevel' combine (bridge) outputs for u.e with two
speakers. Nevel' ground negative speakei' leads to chassis ground.
NOTE: Only connect speakers with a nom'nal'mp~
of if ohms. Speakers with a load Impedance less than if
ohms could damage the unit.
Amplifier
!!
IMPORTANT!
The pink parking
wire MUST be
connected to the
switched side of the
parking break
circuit (the part that
becomes groUnded
when the brake is
applied).
R (Red)
L(\Nhite)
R
(Red)
L(\Nhite)
Red
Subwoofer Out
(Blue)
Partdng Brake (Pink) e
camera In
(Yellow)
VIdeo OUt 1(Yellow)
SWC (Steering Vllheel Control)
(Requiree PACSWI-PS InterfaceAdapIer)
Accessoryngnltlon
Connect to existing radio wire
or radio fuse.
Power Antenna
Connectto power antenna or amplifier.
If not used, tape bare end of wire.
Blue
Rear Line out ,.-:::c:J
Ra'--'''IIIII_~G!'''ra·y--o('--:o
Front Line out ,.-:::c:J
1D--"'~-"""'!B~la·ck"':E--<'--:o
SATL('MI1te)
SATR (Red)
@)
o
Antenna
o
Battery
Connect the yellow wire to the battery
or 12 volt power source that Isalways
live. This wire MUST be connected
for the nKIIo to worlf.
Yellow
"+
-
-
-
Chassis Ground
Connect the black wire to the factory ground wire. If a
factory ground wire Is not provided, locate aclean,
unpainted metal part of the dash and secure the ground
wire with a "ring" terminal and a sheet metal screw.
IPod NOTE: Video playback not supportedfor all
(Sold separately) iPods. see iPod section formore information.
FRONT REAR
WhlteIBl8ck
Whle
GrayJ8lack GreenIBI8ck
GrMn
~
Purple
Stripe Stripe Gray Stripe
:! H(+) (-) (+) (-) (+) H(+)
aI
f
~
~
0 0
0
'U
~
;:,
~
l
Ie
;a
Left Speaker
Right Speaker Left Speaker Right Speaker
(Front) (Front)
(Rear) (Rear)
3
SAT BUS
Satellite Radio Tuner
(sold separately)

<l!:~~.D VM8013HD
FRONT PANEL RELEASE
The front panel release button (23) releases the mechanism that holds the
front panel to the chassis.
Detaching the Front Panel
To detach the front panel, perform the following steps:
1. Press
the power button (1) to turn the unit off.
2.
Press the front panel release button to flip the panel down.
3. Grasp the right side to release the front panel and then pull it at an
angle to remove the right side from the chassis.
4. Store
the front panel it in the supplied carrying 'case to protect it from dirt
and damage and take it with you to prevent theft.
Re-attaching the Front Panel
Before re-attaching the front panel, make sure the electrical tetminals on
the
back of the panel are free of dust and dirt, as debris could cause
intermittent operation or other malfunctions.
To re-attach the front panel:
1. With
the panel laying flat (in the "open" position), insert the left side of
the panel in place until correctly engaged.
2.
Gently press the right side of the panel until the mechanism locks it into
place.
Lift
upward to close the panel.
4

VM8013HD <[1_ ,\SI°'5>
REMOTE CONTROL OPERATION
The remote control will allowyou to
control
the advanced functions of
the VM8013HD.
5
Operating Range
The remote control sensor (19) is located near
the bottom of the front panel. left of the LCD
screen. The remote control can operate within
adistance
of 3-Sm.
Replacing the Battery
When the range of operation of the remote
control becomes short
or stops functioning,
replace the battery with anew lithium battery.
Be sure to observe the proper polarity, as indicated below.
30·

Q\"'~5> VM8013HD
REMOTE CONTROL FUNCTIONS
Table 1: Remote Control Functions
#
Button
Tuner SAT CD
iPod DVD
1I
LUUM
Magnny Image
2TITLE Select Video
Mode View DVD Title Screen
3
Power
Power On; Power On; Power On; Power On; Power On;
Press and hold to Power Olf Press and hold to Power Olf Press and hold to Power Olf Press and hold to Power Olf
Press and ho/dto Power Off
4 SETUP
Display Setup Menu
Display Setup Menu
Display Setup Menu
Display Setup Menu Display Setup Menu
5Navigation
Arrows
Down/Up: Preset NaVigation Down/Up: Preset NaVigation Down/Up: Screen Naviga- Down/Up: Screen Navigation Left/Right: Fast ReverselFast
tion; Left/Right: Folder Navi- Forward; Up/Down:
Slow
gation Reverse/Slow Forward
6
ENTER
Confirm Entry Confirm Entry Confirm Entry Confirm Entry Confirm Entry
7
CLEAR
8Direct Entry Direct
Channel Entry Direct Track Entry
9
SEL
Audio Mode: Select BAS, Audio Mode: Select BAS, Audio Mode: Select BAS, Audio
Mode: Select BAS. Audio Mode: Select BAS,
TRE, BAL, FAD;
Press and TRE, BAL. FAD; Press and TRE. BAL, FAD; Press and TRE, BAL, FAD; Press and TRE, BAL, FAD; Press and
hold for System Menu hold for System Menu; hold for System Menu hold for System Menu hold for System Menu
ENTER in Category Mode
10 VOL (Volume Control) Volume up/down Select
next/previous item in Volume upldown Volume upldown
Volume upldown
Category Mode
11 MUTE
Silence Audio Output Silence Audio Output
Silence Audio Output Silence Audio Output
Silence Audio Output
12 SEEK
Search Next/Previous Chan- Search Next/Previous Chan- Next/Previous Track; Next/Previous Track; Next/Previous Track;
nel; nel;
Press and hold to Fast For- Press and hold to Fast For-
Press and ho/dto Fast For-
Press and hold to Scan Press and hold to Scan ward/Reverse ward/Reverse wardlReverse
Channels
upldown Channels up/down
13 SUB.T View/Change Subtitle Lan-
guage
14 SRC (Source) Select Playing
Mode Select Playing Mode Select Playing Mode Select Playing Mode Select Playing
Mode
15 REPEAT
Repeat Current Track Repeat Current Track Repeat Current Chapter
16 A-B Repeat Repeat Section Repeat Section
17 StoplReturn StoplReturn Stop/Return Stop/Return
18
Play/Pause Play/Pause Play/Pause Play/Pause
19 GOTO Search View HD Multicast stations;
GOTO Specific Area of Disc
GOTO Specific Area of Disc
Press and hold to select:
Auto, Digital, Analog
20 MENU
Return to Previous Menu View DVD Setup Menu;
PBC for VCD 2.0 and
up
21 ROM Play all Tracks in Random Play all
Tracks in Random Play all Chapters in Random
Order Order Order
22
AUDIO Select Audio Mode View/Change disc Audio Lan-
guage
23 DISP
Enter Program Search; Display Direct Entry Menu; Press and hold to set clock Press and hold to set clock Press and hold to set clock
Press and hold to set clock Press and hold to set clock
24 ANGLE Show alternate angles, if
available
25 BAND Select Band (AM1, AM2. Select Band (SAT1. SAT2. Select PAL, NTSC, AUTO
FM1. FM2, FM3)
SAD)
6

OPERATION
Power
Press the <!> (power) button (1) to turn the unit on. Press and hold the power
button again to turn the unit off.
NOTE: LCD panels may take longer to respond when SUbjected to cold
temperatures for an extended period of time. In addition, the visibility
of the numbers on the LCD may decrease slightly. The LCD display
will return to normal when the temperature increases to a normal
range.
Source
Press the SRC button (6) repeatedly to scan the various sources. Asource
is only displayed
when accessible (optional equipment required for some
sources). Available modes include Radio (FM, AM), SAT, DVD, SO, USB,
iPod and auxiliary (AUX IN).
External Devices
External peripheral devices, including a game console, camcorder,
navigation unit, iPod, Zune, etc. can be connected to
the AN connector (18)
on the front
of this unit using the 3.5mm Media Cable (included). Select
"SOURCE » AUX IN" to access auxiliary devices. You cannot directly
control external devices connected to the
AN IN inputs.
Audio Mute
Press the <!> (power) button (1) to silence the audio volume. "'"" appears
on the display. Press
<!> (power) again to restore volume to the previous
setting.
Volume Control
To increase the volume, turn the VOUSEUMENU (rotary encoder) (2)
clockwise.
To decrease the volume, turn the rotary encoder counter-
clockwise.
When volume is adjusted, the volume level will be shown on the
display panel as anumber ranging from "0" (lowest) to "40" (highest).
Steering Wheel Control (SWC)
The VM8013HD is compatible with the PAC (Pacific Accessory Corporation)
steering
wheel control adapter SWI-PS. A 3.5mm female connector
(labeled
"SWC Interface") on the back ofthe head unit allows connectivity to
the PAC adapter. Please refer to the instructions included with the PAC
adapter for detailed installation information.
The following controls are available for most vehicles:
7
1. Vol Down
2. Vol Up
3. Mute
4. Seek Down IPrevious Track
5. Seek Up I Next Track
6.
SRC (Source)
7. Band
Audio Menu
Press the VOUSEUMENU button (2) to access the audio menu. Press the
VOUSEUMENU button repeatedly to move through the list of menu
options.
SUb_w: When the
Low Pass Filter is activated (see "Menu Operation"
on page 8), you can
use the VOUSEUMENU rotary encoder to adjust
the
subwoofer volume from "-14" to "0".
Bass: Turn the
VOUSEUMENU rotary encoder (2) to adjust the bass
level
from "+7" to "-7".
Treble: Turn the
VOUSEUMENU rotary encoder to adjust the treble
level from "+7" to "-7".
Balance: Turn
the VOUSEUMENU rotary encoder to adjust the
balance from "R?" (full right) to "L7" (full left).
Fader: Turn the
VOUSEUMENU rotary encoder to adjust the fader
from "F7" (full front) to "R7" (full rear).
The unitautomatically saves your changes and exitsthe audio control menu
after five seconds
of inactivity.
NOTE: This model is equipped with source tone memory. Any
changes to the Bass, Treble, and Sub-ware renected only in the active
source.

Menu Operation
Press and hold the VOUSEUMENU button (2) for more than two seconds
to access the menu. Press the VOUSEUMENU button to move through the
following menu options: Equalizer, Loud Set, Beep Set, 12/24 Mode (clock),
Mirror Image, Vol Mode, A-VOL, Sub LPF and Area Set. The following
procedures assume you have already accessed the menu.
Equalizer
The Equalizer function applies preset sound effects to the unit's audio
output signal. Turn the rotary encoder to select from the following equalizer
options: "Off', "Rock", "Hip Hop", "Dance" and "Acoustic". With the equalizer
function activated,
if bass or treble is adjusted, the EO Mode will revert to
"Off'.
When the equalizer function is activated, the most recently selected bassI
treble levels cannot be adjusted. When the equalizer function is not active,
the unit will return to the most recently selected bass and treble levels.
Loud Set
When listening to music at low volumes, this feature will selectively boost
certain bass and treble frequencies. "Off' is the default setting. Turn the
rotary encoder to select "On".
Beep Set
The beep tone feature allows the selection of an audible beep tone to be
heard each
time the menu is accessed. "On" is the default setting. Turn the
rotary encoder to select "Off'.
8
12/24 Mode
This option allows selection of a 12 hour or 24 hour clock format. "12 Hours
ft
is the default setting. Turn the rotary encoder to change to the 24 hour clock
format.
Mirror Image
This option allows for selection of a mirror image view when a rear view
backup camera (sold separately) is connected to the CAMERA IN input on
the back of the radio. Turn the rotary encoder to select "On" or "Off'.
Vol Mode
Turn the rotary encoder to select "Last
ft
or "Adjust".
Last: When the unit is turned on, the volume will resume at the level
selected
when last turned off.
Adjust:
If choosing "Adjust", use the A-VOL setting to specify aturn-on
volume.
Turn-On Volume (A-VOL)
After selecting "Adjust" for Vol Mode, press the VOUSEUMENU button to
access the A-VOL setting and then turn the rotary encoder to select the
desired turn-on volume level. When this option is selected, the unitwill
revert
to the adjusted volume each time the unit is turned on.
Sub LPF (Low Pass Frequency)
After connecting a subwoofer to the back of the unit, turn the rotary encoder
to select a crossover frequency: OFF, 80,120 or 160Hz.
Area Set
This option allows you to select the appropriate frequency spacing for your
area. "U.S.A." is the default setting. Turn the rotary encoder to select
"EUROPE".
Dimmer
Press the DIM button (15) on the front panel to dim the screen by 112. Press
again
to darken the screen completely. Press athird time to resume full
brightness.
Clock Set
1. Press and hold the DISP button (7) until the clock blinks.
2. Turn
the VOUSEUMENU rotary encoder (2) to set the minutes.
3.
Press the VOUSEUMENU button (2) to confirm and move to the hour
field.
4.
Turn the VOUSEUMENU rotary encoder to set the hour.
5. Press the DISP button to set the clock and exit the clock set function.

VM8013HD <TI:'Js~S>
Reset Button
The RESET button (22) is located behind the front panel and can only be
accessed with the front panel removed. Resetting the unit will erase the
time and preset memories. It should only be activated upon initial
installation after all wiring
is complete, or ifthere is amalfunction of any of
the switches on the unit. In these circumstances, pressing the RESET
button will clear the system and return the unit to default operation.
L:::J..
o@I
CARD I
IN
-
9

~\S!3> VM8013HD
SATELLITE RADIO OPERATION
Listeners can subscribe to X~ Radio on the Web by visiting
www.xmradio.com. or by calling [phone]. Customers should
have their Radio ID ready (see "Displaying the Identification (lD)
Code''). Customers can receive a limited number of free-to-air
channels without activation.
Accessing Satellite Radio Mode
Press the SRC button (6) on the front panel or remote control (14) to switch
to the SAT source.
CHAN: XM Preview
P1 XM Preview
P2 XM Preview
1. SAT Channel Name
2. SAT Channel Number
3. SAT Band
4. lime/Clock
5. Artist and litle Information
6. Current Preset Channels
7. Source Indicator
Displaying the Identification (ID) Code
Before you listen to satellite radio, you must subscribe to the service using
your radio's identification number. To display the radio 10, press the DISP
button three times or use the 1« tuning button (17) to tune to channel "000".
The screen displays the radio 10 where the channel name is usually
displayed.
10
select a Band
Press the BAND button (3) to change between three SAT bands (SAT1,
SAT2 and SAT3). Each band stores up to six preset stations.
Selecting a Station
Press the »1 or 1« tuning button (17) to tune to another station.
Preset Mode
Six numbered preset buttons store and recall stations for each band. All six
stored stations (P1-P6)
for the current band can be viewed on the screen.
Use the remote control up/down arrow buttons (5) to scroll through the list.
Storing a Station
1. Select a band (if needed), then select astation.
2. Press
and hold a preset button (numbers 1-6) on the front panel or
remote control.
3.
The preset number and station appears highlighted.
Recalling a Station
1. Select aband (if needed).
2. Press afront panel
or remote control preset button (numbers 1-6) to
select the corresponding stored station.
Channel Search
To access Channel Search mode, press the DlSP button (7). The list of all
available
channels appears on the screen.
1. Rotate the
VOUSEUMENU rotary encoder (2) on the control panel or
press the up/down arrow keys (5) on the remote control to navigate the
list
of channels.
2. Press
the VOUSEUMENU button on the control panel or the ENTER
button (6) on the remote control to select achannel.

VM8013HD <li~~3>
Category Search
1. To access Category Search mode, press the DISP button (7) twice. The
list of available categories appears on the screen.
8)
SAT1
CH001 ~ol:'2
CHAN: XM Preview
( 01 News )
02 Sports
--
( Title: www.xmradio.com
)
2. Rotate the VOUSEUMENU rotary encoder (2) on the control panel or
press the up/down arrow keys (5) on the remote control to navigate the
list of categories.
3. Press the VOUSEUMENU button on the control panel or the ENTER
button (6) on the remote control to select the desired category. Alist of
stations in the selected category appears on the screen.
4. Rotate the VOUSEUMENU rotary encoder on the control panel or
press the up/down arrow keys on the remote control to navigate the list
of stations in the selected category.
5.
Press the VOLISEUMENU button on the control panel or the ENTER
button (6) on the remote control to select astation.
Direct Channel Input
1. To enter aradio station directly, press the DISP button on the front
panel (7) or remote control (23) three times to display the DIRECT
channel input screen.
I[ CHANN~~RECT )1
Enter the desired radio station using the remote control number pad (8)
followed by
the ENTER button, or perform the following steps:
1. Turn the
VOUSEUMENU rotary encoder to select the third digit of the
desired channel (0-9).
2.
Press the VOUSEUMENU button to enter the number and move to the
second position.
11
3. Turn the rotary encoder again to select the second digit of the desired
channel (0 -9).
4. Press VOUSEUMENU to enter the second number and move to the
first position. (Press and hold if channel is only 2 digits and you are
ready to tune to the channel.)
5. Turn the rotary encoder again to select the first digit of the channel you
want to tune to (0 -2).
6. Press the VOUSEUMENU button to tune to the selected station.

~~ VM8013HD
RADIO OPERATION
About HD Radio™ Technology
HD Radio technology allows CD-quality digital broadcasting of your local
AM and FM radio stations. HD Radio broadcasts can include multiple
channels on the same frequency, which is called multicasting. With
multicasting,
you can receive up to eight additional multicast channels:
HD1-HD8.
With your VM8013HD radio, you will receive HD Radio digital broadcasts
automatically when tuned to astation that offers HD Radio technology.
NOTE: Not all FM or AM stations offer HD Radio (digital) broadcasting.
You can receive both analog and digital stations with the VMB013HD.
Accessing Radio Mode
Press the SRC button (6) on the front panel or remote control (14) to switch
to the RADIO source.
FM1 P1
AUTO
P1 87.50MHz
P2 90.10MHz
ps: so SMALL
6
1. Auto, Analog, Digital Reception Indicator
2. Radio Station Frequency
3. AM/FM Band
4. Time/Clock
5. Program Information: Artist, Title, Type
NOTE: The amount of information displayed when receiving an HD
Radio signal is dependent upon what is being broadcast. Some stations
broadcast their call/etters (name), the artist's name, song title, and
category of music.
12
6. Current Preset Channels
7. Source Indicator
8. HD Radio Station Indicator
Selecting the AM/FM Band
Press the BAND button (3) to change between the AM and FM band.
Tuning
Seek Tuning
Press the TUNEITRACK »1 or 1« buttons (17) to seek the nexUprevious
station automatically.
Manual Tuning
Press and hold the TUNEITRACK »1 or 1« buttons (17) to enter Manual
tuning mode. Press the buttons again to move the radio frequency number
up or down one step.
HD Radio Multicast Channels
To tune to an HD Radio multicast channel, tune to the main signal and then
press the PGM button (14) on the control panel. Alist of multicast channels
will be displayed (HD-1, HD-2 etc).
Use the rotary encoder to navigate the list and then press to select a
multicast channel.
Use the remote control arrow keys and ENTER button to select a
multicast channel.
Press and ho/dthe PGM button to change between "Auto", "Digital" and
"Analog". When set to "AUTO", the station will first be received in Analog
but will change to Digital when adigital signal is detected and the HD icon

VM8013HD <1L ..... s!:.S>
will illuminate. Ifthe digitalsignal becomes unavailable, the unitwill revert to
Analog reception.
Program Search
To view the Program Type categories when listening to HD Radio
broadcasting, press the DISP button on the control panel (7) or remote
control (23). Program type categories are listed, allowing listeners to find
similar programming by genre. When aProgram Type category is selected,
the radio will start scanning for stations broadcasting in the selected
category.
Use the TUNEITRACK »1 or 1« buttons (17) to change the
category.
Preset Stations
You can store up to 18 presets for FM and 6presets for AM, which can then
be instantly recalled by pressing the associated preset button (8-13). To
store astation, turn the radio on and select the desired band and station.
Press and hold the desired preset button (numbered one through six on the
face of the radio or remote control) for more than two seconds. When
stored, the preset numberwill appear in the display. The station is now
stored and can be recalled by pressing the corresponding preset button.
Repeat for the remaining five presets on the current band and for presets on
the other four bands.
NOTE: Multicast stations can be stored as presets, but the unit must
be in Digital or Auto reception mode to receive them.
Preview Scan
Press the button (16) to scan and play all strong stations for 5seconds
each. Press again to stop scanning and play the current station.
Automatic Store
Press and hold the ....... button (16) to select either 18 strong FM stations or
6 AM and store them for quick access using the Automatic Store (AS)
feature. AS only stores stations for the current band. After entering the
stations into memory, the unitwill automatically stop at each station for five
seconds, allowing you
to preview each selection. When using the AS
feature, the new stations replace any stations already stored in preset
memory.
NOTE: You can stop the Automatic Store function at any time by
pressing the ....... button again.
13

<IL'~ VM8013HD
To stop disc play and eject the disc, press the 0button to flip the front
panel down and then press the eject button (21).
Loading a USB Device
Insert the USB device intQ the USB connector (5) on the front of the unit.
The unit will read the files on the USB device automatically.
To remove the USB device, press the SRC button (6) to switch to another
mode and then remove the USB device from the USB connector.
Notes on MP3/WMA Play
MP3 and VIlMA (Windows Media Audio) music files are digital audio files
that are compressed to allow more files on a single CD. This unit can play
MP3IWMA and video directly from files contained on a CD-RlRW, DVD-
ROM, DVD+RW, DVD-RW, DVD+R, DVD-R and DVD-VIDEO, or an SO
card
or USB Device using the buttons on the receiver (or remote control) as
described below.
Many types of software are available for converting audio files into MP31
VIlMA formats.
Jensen recommends Nero or Roxio Easy CD Creator.
This unit can play MP3 (MPEG1, 2, 2.5 Audio Layer 3). However, the MP3
recording media and accepted formats are limited. When writing MP31
VIlMA,
pay attention to the following restrictions.
Acceptable Media
The MP3IWMA recording media acceptable to this unit are CD-ROM, CD-
R, and CD-RW. The unit will also play MP3, VIlMA, or photo files written to
SO Cards, USB Devices.
Depending on the media type and recording method, some CD-RlRWs may
be incompatible with this unit. When using CD-RW,'use full format rather
than quick format to prevent malfunction.
This unit supports playback of MP3IWMA and CDDA (CDA), Mixed-Mode
CDs and CD-Extra (including multi-session discs). Discs on which the
session has not been closed will not play.
Acceptable Medium Formats
The following formats are available for the media used in this unit. The
maximum number of characters used for file name, including the delimiter
('.") and three-character extension, are indicated in parentheses.
ISO 9660 Level 1 (11 characters)
ISO 9660 Level 2 (31 characters)
Joliet (31 characters)
NOTE: This unit supports FAT 16 and FAT 32 file systems. The unit
supports USB 1.1 only, but will play USB 2.0 devices at USB 1.1 speed.
-
ICARDI
IN
6-
o@
DISC/MP3IWMA PLAYBACK
Inserting and Ejecting a Disc
Press the 0 button (23) to flip the front panel down. Insert adisc, label side
up, into the disc slot (20).
Loading an SD Card
Open the panel and insert the SD card into the SD Card slot (4). Close the
panel and the unit wil!...\ead the files on the card automatically.
NOTE: The unit is designed for play of standard 5" (12 cm.) discs only.
Do not.attempt to use 3" (8 cm.) CD singles in this unit, either with or
without an adaptor, as damage to the player and/or the disc may
occur. Such damage will not be covered by the warranty on this
product.
To remove the card, first press the SRC button (6) to switch to another
mode and stop SD playback. Press the SD card to pop it out, then remove
the card.
14

VM8013HD ~
Romeo (31 characters)
Up to 200 characters can be displayed in the long file name format. For a
list
of available characters, see the instruction manual of the wliting
software and
the section "Enteling File and Folder Names" that follows. The
media reproducible on this unit has the following limitations:
Maximum number of nested folders: 8
Maximum number of files per disc: 1500
Maximum number of folders per disc: 255
MP3IWMA files wlitten in formats other than those listed above will not play
successfully and their file
or folder names will not display properly.
MP3IWMA Encoder and CD Writer Settings
Use the following settings when compressing audio data with the MP3
encoder.
Transfer bit rate: 8 - 320 kbps
Sampling frequency: 8, 11.025, 12, 16, 22.05, 24, 32, 44.1,
48 kHz
When using aCO wliter to record MP3IWMA up to the maximum disc
capacity, disable additional
wliting. To record an empty disc up to the
maximum capacity at once, select the "disc at once" option.
Entering ID3 Tag
This unit supports 103 tag version 2.0.
For character codes, refer to the table to
the right.
Entering File and Folder Names
Names using the code list characters
are
the only file names and folder
names that can be entered and
displayed. Using any othercharacterwill
cause the file and folder names to be
displayed incorrectly. The unit
recognizes and plays only files with
the MP3IWMA extension.
NOTE: A file name entered with characters not on the code list may
not play correctly.
Electronic Shock Protection
10 seconds for CO-OA (COA)
>45 seconds for MP3 recorded at 44.1kHz, 128kbps
>90 seconds for WMA recorded at 44.1kHz, 128kbps
15
Bit Rates
The unit supports bit rates from 32 -320 kbps.
MP3 Playing Order
When selected,for play, files and folders (Folder Search, File Search or
Folder Select) are accessed in the order in which they were wlitten to the
media. As aresult, the order in which they are expected to be played may
not match the
order in which they are actually played. You may be able to
set the order in which MP3IWMA files are to be played by assigning file
names beginning with play sequence numbers such as "01" to "99".
For example, a medium with the following folder/file hierarchy is subject to
Folder Search, File Search or Folder Select as shown below.
D Folder
Jl fl.
LAv" 1 level 3
The VM8013HO player will only recognize three folder levels and does not
display folders containing only
other folders. In the example above, the unit
will display folders 3, 4, 6, and 8, but
not 2and 7 since they do not contain

The Smashing PUff...----tI1
~ 01· Manson, Marilyn •..--=F----+-hl
7. Source Indicator
8. Elapsed Playing Time for Current Song
Controlling Disc or File Playback
Pause
Press the 11>/11 button (8) to suspend playback. Press the 11>/11 button
again
to resume playback. Tracks are played in the order they are written to
the disc/card, unless another operation is requested.
Stop
Press and hold to stop playback. If viewing video or photos, the system
returns to the file menu.
Track Select
Press the TUNEITRACK »1 or 1« buttons (17) for less than one second to
advance to the next tracklfile. The selected track number will appear on the
display.
Navigate Files
The S/DN (12) and 6/UP buttons (13) are used to navigate up and down
within the file menu. Press and hold to move down/up a folder level. The
current folder name is displayed at the top of the screen.
Fast Forward/Reverse
Press and hold the TUNEITRACK »1 or 1« buttons (17) to fast forward or
fast reverse. Press and hold once for 2X. Press and hold additional times
for 4X, 8X, 20X or PLAY. Press the play/pause >/11 button (8) to end fast
forward or reverse and resume normal playback.
Intro Scan (INT)
During playback, press the 21INT button (9) to select "INTRO" and play the
first 10 seconds of each track/file, as indicated by the '00. symbol. When the
desired track is reached, press 211NT again to end the scan and play the
selected track.
Repeat (RPT)
Press the 3/RPT button (10) multiple times during playback to select from
the following repeat play options:
VCD/CD: RPT ONE (track), RPT ALL (disc), RPT OFF
DVD: RPT CHAPTER, RPT TITLE, RPT OFF
MP31WMA: Repeat File, Repeat Directory/Folder, Repeat All (disc),
Repeat Off
4
01: 2
AM
•o (ROOT)
MP3 001/141 02:19
any tracks directly. Folder 5 is not recognized at all since it is at the fourth
level.
Changing the Source
If adisc is already in the disc slot but is not playing, press the SRC button
(6) on
the front panel or remote control (14) to switch to the DISC source. To
play files from an SO or USB that is already inserted, choose the CARD or
USB source. The MP3 playback screen is indicated bel.ow:
1. CDIMP3IWMA Indicator
2.
Current of Total Tracks
3.
Current Folder Level
4.
Time/Clock
5. 103 Artist and Title Information (MP3 only)
6.
Songs on Disc
16

VM8013HD <[~s£S>
Random (RDM)
Press the 4/RDM button (11) during playback to select "RANDOM" and play
alltracks/files in random, shuffled order. Press
4/RDM again to stop random
play.
Section Repeat (A-B)
To repeat aspecified section of atrack, perform the following steps:
1. Press the A->B button (16) on the remote controlto select the starting
point. The display will show "REPEATA-".
2. Press A->B when you reach the desired ending point. The display
shows "REPEATA-B" and the selected section will play repeatedly.
To cancel section repeat, press
the A->B button again. "A-B CANCEL"
appears on the display.
GOTO Track Time Access
Use the GOTO function to access aspecific position on a track directly.
1. Press the GOTO button (19) on the remote control. The Search
(lime -:-:-) window will appear.
2. Use the number keys on the remote control to enter the exact time on
the current track from which you would like playback to begin.
3. Press the ENTER button to confirm and begin playback from the
selected
track time.
VCD PlayBack Control (VCD Only)
If you insert a VCD with playback control, playback automatically starts at
the beginning of the first track. Press the MENU button (20) on the remote
control
to to tum playback control on/off.
Additional DVD/Video Playback Features
NOTE: You cannot view video while driving the car. When attempting
to view video while the parking break is not engaged, the following
message will appear on the screen: WARNING /I Engage Parking
Brake to View Video.
The following remote control features are available during DVD playback:
AUDIO: Press to choose an alternate audio language, if available. This
button
may also show differentsurround sound options encoded on the
DVD.
SUB-T: Press to select an alternate subtitle language, if available.
TITLE: Press
to display the title or chapter list. Use the ., ... , ... or ~
cursor buttons or the numeric buttons to enter atitle or chapter number,
and then press ENTER to play.
17
ANGLE: Press to select an alternate viewing angle, if available.
ZOOM: Press to zoom the picture at X2, X3, X4, X1/4, X1/2, or select
OFF to return to normal view.
Slow Forward/Slow Reverse: Press the ./ ... buttons on the remote
control
or the 5/6 buttons (10, 13) on the control panel to slow rewind/
slow reverse. Press once for 1/2 speed. Press additional times for 1/4,
1/6, or 1/8 speed. Press the play/pause >/11 button (8) to end fast
forward or reverse and resume normal playback.
NOTE: Feature availability is dependent on DVD embedded
information.
NOTE: The VM8013HD does not support Surround Sound decoding.

<[V~J-S> VM8013HD
CONTROLLING YOUR iPod
The unitwill automatically switch to iPod mode when an iPod is plugged
into the iPod cable. To return to the iPod screen from any other source,
press the SRC button (6) on the front panel and select SOURCE »iPod.
After switching to iPod source, the iPod menu appears on the screen.
NOTE: Be sure your iPod has the latest Apple firmware installed to
avoid connectivity issues.
The following remote control buttons are used to access the iPod menus:
Menu Remote Control
Music
AUDIO
PhotoslVideos TITLE
Use the navigation arrows on the remote control (5) or the 5 DN/6 UP
buttons on
the control panel to navigate the iPod menus. Press the ENTER
( ...... )button on the front panel (16) or remote control (6) to select the
highlighted menu option.
iPod Music Playback
The iPod music menu is automatically accessed when an iPod is connected
to the unit or the source is changed to iPod while the iPod is connected.
Press the> II button on the front panel (8) or remote control (18) to play
or pause the selected track.
Press the »1 button on the front panel (17) or remote control (12) to
play the next file.
Press
the 1« button on the front panel (17) or remote control (12) to
play the previous file.
Press
the ENTER ( ...... )button on the front panel (16) or remote control
(6)
to select the highlighted menu option.
Press the BAND button on the front panel (3) or remote control (25) to
return to the previous menu.
Fast Forward/Fast Reverse
Press and hold the 1« or »1 buttons on the control panel (17) or remote
control (12)
for 1 second and continue to hold for fast forward or fast
reverse. Release to resume normal playback.
18
PhotoMdeo Playback
While iPod photos and videos can be viewed on the VM8013HD screen,
you must use the iPod to control photo and video playback options.
Press the TITLE button (2) on the remote control and the VM8013HD will
release control back to the iPod so you can select video media to be
displayed on the TFT monitor. To return to iPod music mode, press the
PGM button (14) on the front panel or the AUDIO button (22) on the remote
control.
You can also
press and hold the PGM button on the front panel to access
photo/video playback from the iPod to the radio TFT screen.
NOTE: Requires 5th Generation or later iPod for PhotoMdeo Support.
Compatible with iPod 5 or 5.5, iPod Classic, iPod Touch, iPhone and
iPod Nano with Video.