Jensen VX6020 User manual

VX6020
Installation Guide
What’s in the Box
The following items are supplied with
the VX6020:
• VX6020 Head Unit
• Custom Cosmetic Trim Ring
• Hardware Bag
• Power/Speaker Output Harness
• GPS Antenna Harness
• I/O Harness
• USB-A to Mini USB Adapter
• Owners Manual & Warranty Card
• Installation Guide
Tools and Supplies
The following tools and supplies are
needed to install the VX6020:
• Torx type, at-head and Philips
screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio (screw
driver, socket wrench set or other
tools)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16 – 18 gauge speaker wire
WARNING! Never install this unit where operation and viewing could interfere with
safe driving conditions.

Optional Equipment
• Steering Wheel Control (SWC)- The VX6020 is SWC ready for vehicles equipped with the option. See wiring diagram
for installation details.
• Rear Camera- The VX6020 is Rear Camera ready for vehicles equipped with the option. See wiring diagram for
installation details.
Disconnect the Battery
• To prevent a short circuit, be sure to turn o the ignition and remove the negative (-) battery cable prior to installation.
NOTE: If the VX6020 is to be installed in a car equipped with an on-board drive or navigation computer, do not
disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these
conditions, use extra caution during installation to avoid causing a short circuit.
Replacing the Fuse
• When replacing the vehicles Radio fuse always use the proper rated replacement fuse. Using a fuse with an improper
rating could damage the unit and cause a re.
ISO-DIN Installation
The VX6020 is designed to t into a 2.0 DIN dashboard opening. The unit has threaded holes in the chassis side panels
which may be used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai
and Honda vehicles to mount the radio to the dashboard. Please consult with your local car stereo specialty shop for
assistance on this type of installation.
NOTE: It is the end-users responsibility to install and operate this unit in a manner in accordance with local, state and
federal laws. The PARKING BRAKE wire MUST BE CONNECTED as directed in the manual.
Using the Cosmetic Trim Ring
A cosmetic trim ring is supplied with the head unit for installation exibility.
This unit will t into most import dashes with little or no modication to the
dash board/cavity. Some US domestic vehicle dashes will accept a Double-
DIN chassis, but there is usually a small gap between the radio and dash
piece after installation is complete. In this case, use the appropriate trim
ring to conceal any gaps that may be present.
DASHBOARD
TAB
Step 1-b
Step 1-c
Step 2
Step 5-c
1.Remove the existing factory radio from the dashboard or center
console mounting. Save all hardware and brackets as they will be
used to mount the new radio.
2.Remove the factory mounting brackets and hardware from the
existing radio and attach them to the new radio.
CAUTION! Do not exceed M5 X 6MM screw size. Longer screws may
damage components inside the chassis.
3.Place the radio in front of the dashboard opening so the wiring can
be brought through the mounting sleeve. Follow the wiring diagram
carefully and make certain all connections are secure and insulated
with wire nuts or electrical tape. After completing the wiring
connections, plug the ISO connectors into the mating sockets on
the rear of the chassis. Turn the unit on to conrm operation (vehicle
ignition switch must be“on”). If the unit does not operate, re-check all
wiring until the problem is corrected.
4.Mount the new radio assembly to the dashboard or center console
using the reverse procedure in step 1 above.
CAUTION! Be careful not to damage the car wiring.
EJECT
MENU
NOTE: For proper operation of the CD/DVD player, the chassis must be mounted within 30° of horizontal. Make sure
the unit is mounted within this limitation.
1

Wiring Diagram
CAUTION! IMPORTANT: Incorrect wiring connections can damage the unit. Follow the wiring instructions carefully,
or have the installation handled by an experienced technician.
Need Help? For technical assistance, call the Jensen customer support line at 1-800-323-4815.
SWC A and SWC B are to be connected to the two leads of the SWC harness in the automobile. The third wire, SWC GND is to be connected to the lead identied as Ground on the SWC lead diagram for the specic automobile. Wiring of the SWC lead in the auto steering wheel may vary depending on the type of automobile. Please consult the wire harness diagram for the pinout of your specic automobile’s SWC conguration. Some automobiles may not be compatible with this 3 wire SWC resistive input. AVX recommends that installation of this radio be performed by a professional installer.
KEY A : SWC A: Primary programming lead KEY A : SWC B: Secondary programming lead
MOBILE POWER AMP
Power On
Trigger Wire
SWC A
CHASSIS GROUND BATTERY 12V (+) ACC / IGNITION (+) BRAKE (-) REVERSE (+) POWER ANT/AMP. (+)
ILLUMINATION (+)
LEFT FRONT SPEAKER (-)
LEFT FRONT SPEAKER (+)
RIGHT FRONT SPEAKER (-)
RIGHT FRONT SPEAKER (+)
LEFT REAR SPEAKER (-) LEFT REAR SPEAKER (+)
RIGHT REAR SPEAKER (-)
RIGHT REAR SPEAKER (+)
SWC B SWC GROUND
BLACK YELLOW RED
PINK
GREEN/WHITE
BLUE
ORANGE/WHITE
GRAY/BLACK
GRAY
GREEN/BLACK GREEN
PURPLE/BLACK ORANGE
PURPLE
WHITE/BROWN BROWN/BLACK
WHITE/BLACK
WHITE
Rear Video
Yellow
Red
White
Red
White
Blue
Radio Ant.
Backup
Camera
Yellow / Camera-Video
GPS Antenna
BLUE + POWERANTENNA & AMPLIFIER TURN-ON
2

128-9244a
Audiovox Electronics Corporation
Hauppauge, NY 11788
Technical Assistance: 1-800-323-4815
www.jensenmobile.com
© 2013 Audiovox
Printed in China