Jenx Corner Seat User manual
Flat Pack Corner Seat
Assembly Instructions Rev04July 2008
A
Base Assembly
Qty: 1
B
Lower Backpad - Left
Assembly
Qty: 1
C
Lower Backpad - Right
Assembly
Qty: 1
Corner Seat - Parts
D
Abduction Block
Qty: 1
G
Height Adjuster Assembly
Qty: 1
E
Upper Backpad - Left
Assembly
Qty: 1
F
Upper Backpad - Right
Assembly
Qty: 1
H
Hip Strap
Qty: 1
I
Chest Strap
Qty: 1
Barrel Nut
D23 (Qty 8) = M6 x 12mm long
Corner Seat - Component Identier
Flathead Assembly Screw
S61 (Qty 2) = M6 x 20mm long
S90 (Qty 3) = M6 x 25mm long
S92 (Qty 4) = M6 x 65mm long
Countersink Screw
S66 (Qty 4) = M6 x 30mm long
Plastic Washer
W6 (Qty 9) = M6 x 18mm Plastic
W44 (Qty 2) = M6 x 30mm Plastic
W33 (Qty 6) = M6 x 25mm Steel
0 5 10 15 20 25 30 35 40 45 50 55 60 65
mm
Tools Required
4mm Allen Key (Supplied)
Flat Blade Screwdriver (Not Provided)
1
Lower Backpad Assembly
Assemble the Lower Back Pad assembly using units
Band C(The larger two pads), and:
2 Barrel nuts (D23)
2 Countersink Screws (S66)
Use a screwdriver to align the barrel nuts and
tighten screws using the allen key provided.
BC
D23
2
Attach Hip Strap (H) to the Lower Backpad
Assembly using the Velcro at each end of the strap.
H
3
Attach the Lower Backpad Assembly to the base (A)
using:
4 Flathead Assembly screws (S92)
4 Barrel nuts (D23)
4 Steel washers (W33)
8 Plastic washers (W6)
Assemble as shown below, aligning the barrel nuts
with a screw driver.
A
W33
W6
S92
4
Upper Backpad Assembly
Next, assemble the Upper Backpad Assembly using
units Eand F, and:
2 Barrel nuts (D23)
2 Countersink screws (S66)
Use a screwdriver to align the barrel nuts and
tighten screws using the allen key provided.
E
F
5
Attach the Height Adjuster, G, to the Upper Backpad
Assembly using:
2 Flathead assembly screws (S61)
Tighten screws using the allen key provided.
G
S61
6
Fix one side of the Step 5assembly to the base
assembly from Step 2 using:
1 Flathead assembly screw (S90)
1 Plastic Washer (W44)
1 Steel Washer (W33)
W44
W33
7
Repeat the previous step with the remaining side
using:
1 Flathead assembly screw (S90)
1 Plastic Washer (W44)
1 Steel Washer (W33)
W44
W33
8
Finally, unzip the abduction block and attach to the
base via the xing hole as shown below, using:
1 Flathead assembly screw (S90)
1 Plastic Washer (W6)
D
9
Attach Chest Strap (I) to Upper Backpads using
Velcro at each end of the strap.
I
JENX LIMITED, Wardsend Road, Shefeld, S6 1RQ, United Kingdom
Tel:+44 (0)114 2853376 Fax: +44 (0)114 2853528
Table of contents
Other Jenx Baby & Toddler Furniture manuals
