Costway BB5581 User manual

BB5581
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
If you're having difficulty, our friendly
customer team is always here to help.
USA office: Fontana AUS office: Truganina GBR office: Ipswich FRA office: Saint Vigor d'Ymonville
USA:[email protected]
AUS:[e-mail]
GBR:[e-mail]
FRA:[e-mail]
Baby High Chair
Chaise Haute pour Bébé

Danger! Keep all small parts and packaging materials for this product
away from babies and children, otherwise they may pose a choking
hazard.
The product must be installed and used under the supervision of an
adult.
Read through each step carefully and follow the proper order.
Remove all packaging, separate and count all parts and hardware
before installation.
Please ensure that all parts are correctly installed, incorrect installation
can lead to a danger.
We recommend that, where possible, all items are assembled near the
area in which they will be placed in use, to avoid moving the product
unnecessarily once assembled.
Ensure a secure surface during installation, and place the product
always on a flat, steady and stable surface.
Before You Start
02 03
EN
WARNING
Avant de Commencer
Veuillez lire attentivement toutes les instructions et les conserver pour la référence ultérieure.
FR
Avertissements Généraux
Danger ! Éloignez toutes les petites pièces et le matériel d’emballage
des bébés et des enfants pour éviter un risque d’étouffement.
Le produit doit être installé et utilisé sous la surveillance d’un adulte.
Lisez attentivement chaque étape et suivez le bon ordre.
Retirez tous les emballages, séparez et comptez toutes les pièces et
le matériel avant l’installation.
Assurez-vous que toutes les pièces sont correctement installées, une
installation incorrecte peut entraîner un danger.
Nous recommandons que, dans la mesure du possible, tous les
articles soient assemblés à proximité de la zone dans laquelle ils
seront utilisés, afin d'éviter de déplacer inutilement le produit une fois
assemblé.
Assurez une surface sûre pendant l’assemblage et placez le produit
toujours sur une surface plane et stable.
IMPORTANT! READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
“Never leave the child unattended".
For products with an active restraint system:“Always use the restraint
system" .
"Falling hazard: Prevent your child from climbing on the product".
“Do not use the product unless all components are correctly fitted and
adjusted".
a statement that the product is intended for children able to sit up
unaided and up to 3 years or a maximum weight of 15 kg.

04 05
EN 3 IN 1 Baby High Chair
IMPORTANT!
READ CAREFULLY AND KEEP
FOR FUTURE REFERENCE.
Instruction Manual
Parts List
Seat unit &
harness x1 Double tray x1 Connector (down
groove) x1 Connector (up groove) x1
Long legs with
pre-drilled holes x2 Long legs x 2 Short legs with
pre-drilled holes x 2 Short legs x 2
Rocker legs x 2 Footrest x 1 Plastic Cover x 1
M6x15mm
Screw x 8 M6x45mm Screw x 7 M6x30mm Screw x 4
M6x60mm
x 4
Barrel nut x 4 Rubber
stopper x 4 Allen key x 1Wood Alignment Pin x 2
11
10
9
8
7
6
5
4
3
2
1
H
G
F
E
D
C
B
A

06 07
Maintenance
Care
Safety
• The correct use and maintenance of this highchair is essential.
• This product requires regular maintenance to keep it in good working order.
• Regularly check all parts of the product to ensure that they are operating
correctly and for signs of wear or damage.
• Do not use this product if any part is broken, torn or missing and use only
spares provided by the manufacturer.
• Position the highchair on a flat, even and horizontal floor and do not elevate
the highchair on any structure or table.
• FALLING HAZARD Prevent your child from climbing on the product.
• Be aware of the risk of tilting when your child can push its feet against a
table or any other structure.
• DO NOT allow anyone to climb or stand on or inside of this highchair. It is
not a step stool or ladder.
• To reduce the risk of injury, position the highchair away from furniture, walls,
hot surfaces and liquids, window covering cords and electrical cords and
position the highchair away from furniture when the child is not being used
at a table with the tray removed.
• The highchair should only be used once the child is capable of reliably and
consistently sitting upright. This is usually around 6 months of age.
• Your child MUST ALWAYS be secured with the harness in Stage 1 until the
child is approx.36 months (3 years).
• This highchair can be used as a junior chair; Stage 2 is suitable for baby
from 36 months (3 years)to 5 years. This chair can be used as a rocking
chair, Stage 3 is suitable for baby from 36 months(3 years) to 5 years.
• Do not use the highchair if any part is broken, torn or missing. If any part of
the highchair is not working correctly, repairs are recommended.
• Regularly check all connections to ensure they are tight.
• Keep the plastic packaging away from children to avoid danger of
suffocation. Conforms to BS EN 14988:2017+A1:2020.
Be aware of the risk of open
and other sources of strong
heat, such as electric fire,
gas fires etc. in the vicinity of
the high chair.
Cleaning
WARNING:
• Frame: Wipe with a damp cloth and wipe dry with a soft cloth.
• Harness: Sponge clean with a mild soap and water solution. Rinse and
wipe dry.
• Never clean any part of highchair with abrasive, ammonia based, bleach
based or spirit type cleaners.
• Ensure the product is fully dry before use or storage.
• Always ensure the highchair is stored in a dry place to prevent mold or
mildew developing.
EN 14988:2017+A1:2020 Standard.

08 09
P1 P2
Assemble the connectors
Insert the downward groove of connector (3) into the upwards groove of connector (4).
Follow the FIG., Insert one screw (B ) into the hole and tighten with Allen key (H).
Ensure the screws are fully tightened.
Assemble the long legs
Align long leg (5) & (6) with assembled connector.
Insert the barrel nut (E) into the hole in the assembled connector. Ensure the "x" mark
is facing outward. Assemble the footrest
Insert the wooden alignment pin(G)in both sides of the footrest, align the footrest(10)
with the pre-drilled holes at the front of the assembled wooden legs.
Failure to fully tighten screws may cause instability.
WARNING:
Baby High Chair (Stage 1) Then insert one fixing screw (C) into the hole in long leg (5) & (6) and tighten with Allen
key (H). Ensure the screws are fully tightened and screw is tight with barrel nut.
Repeat the same procedure for the rest legs.
Ensure to keep the pre-drilled holes at the same side.
P1 P2
P1 P2
P3 P4
P3

10 11
P1 P2 P3
Assemble the supporting plate
Following the FIG., align the plastic cover (11) on the 4 legs , insert 2 screws (A) into
the holes inside each leg and tighten with Allen key(H). Ensure the screws are fully
tightened.
Attach the rubber stoppers
Screw rubber stopper (F) onto the ends of the long legs. Turn the rubber stopper
clockwise to tighten and secure. Repeat for the other 3 legs.
Adjust stoppers to be level with the floor. The highchair should not wobble.
Assemble the seat
Position the seat unit (1) over the assembled wooden legs. Align the holes ensuring
that the seat and the footrest are on the same side.
Insert one screw (B) into the holes allocated on the outside of the long leg and tighten
with Allen key(H). Ensure the screws are fully tightened.
P3 P4

12 13
1
1
12
3
2
2
2
123
45
Insert screws (B) into the
holes from the underside of
the wooden legs and tighten
with Allen key (H). Be careful
not to over-tighten.
The tray features a snack tray which is
easily removed; locate the clip and lift
upwards.
The plastic tray (2) can be adjusted and has 3-positions.
To attach, pull the two adjustment levers and slide the tray along the armrest.
Release the levers at your desired position.
To remove the tray, pull levers and slide tray towards you.
Always use the harness and ensure it is fitted correctly and securely while child is in
the highchair.
WARNING:
Always adjust the harness to fit your child correctly for their comfort and safety. A loose
fitting harness can be very dangerous.
WARNING:
TRAY
1. Slide the shoulder strap buckle clip onto the housing of the waist strap buckle clip.
Repeat for the other side.
2. Insert the completed buckle clip into the buckle housing until it engages securely in
place. Listen for the “click” sound.
3. Repeat for the opposite side.
4. Press the center buckle button to release child from harness.
5. To adjust the shoulder and waist straps length, move the sliders as shown.
Harness

14 15
21
21
1. The harness can be removed for cleaning. Rotate the harness retainers on both
the shoulder and waist harness. Pull them out from the front of seat through the seat
shell and the liner. The highchair can be converted into a chair suitable for children from 36 months (3 years)
to 5 years.
1. Remove the S-point harness. Rotate the harness retainers on both
the shoulder and waist harness, Pull them out from the front of seat through the seat shell
and the liner.
2. Remove the tray.
2. To install the harness, rotate the harness retainers and insert them through the seat
shell and pull them out through the back of the seat.
21
Junior Chair (Stage 2)

16 17
3. Remove the footrest (10). Use
the Allen key (H) and remove the
2 screws. Pull out the footrest.
4. Remove the plastic cover(11)
from the legs. Use the Allen key
and remove the 8 screws. Take off
the plastic cover(11).
5. Remove the long legs (5)
& (6).
Use the Allen key (H) and remove
the screws. Then pull out the 4
long legs.
Assemble the short leg
Align the short leg (7) & (8) with assembled connector.
Insert the barrel nut (E) into the hole in the assembled connector. Ensure the "x" mark
is facing outward.
Then insert one fixing screw (C) into the hole in short leg (7) & (8) and tighten with
Allen key (H). Ensure the screws are fully tightened and screw is tight with barrel nut.
Repeat the same procedure for the rest legs.
Ensure to keep the pre-drilled holes at the same side.
Failure to fully tighten screws may cause instability.
WARNING:

18 19
6. Repeat the same procedure to
assemble the footrest (10) and
plastic cover (11).
7. Repeat the same procedure to
assemble the seat unit. Remove the rubber stopper (F) from the short legs.
8. Remove the rubber stoppers (F) from the long legs.
Turn the rubber stopper clockwise to tighten and secure it on the short leg. Repeat
for the other 3 legs. Adjust stoppers to be level with the floor. The Junior chair should
not wobble.
Each rocker leg has 2 holes, put the rocker leg on the short leg to match
with the holes.
Then Insert one screw (D) into the holes in rocker leg and tighten with
Allen key (H). Ensure the screws are fully tightened.
Repeat the same procedure for the rest 3 holes.
Baby Rocker (Stage 3)