Jetson MotoKicks User manual

Product Overview
Charging your MotoKicks
Getting Started
Battery Indicator Lights
How to Recalibrate
Specs & Features
a. Power Button
b. Mat Sensor
c. Carrying Handle
d. Battery Indicator Lights
e. Charging Port
f. Wheel
g. Training Bar
h. Training Bar Screws (x4)
i. Side Plate
j. Charger
k. Charging Cable
(On opposite side)
Please Note: Images may not relect exact appearance of actual product.
Note: it can take up to 3 recalibration attempts to achieve proper internal alignment.
* Keep the MotoKicks leveled and still throughout the recalibration process.
While recalibrating, do not lean on or put any weight on the MotoKicks.
• Product Dimensions: 10.6” (L) × 5.5” (W) × 4.5” (H) (Each)
• Weight Limit: 220 lbs
• Product Weight: 6.0 lbs (Each)
• Wheel Size: 3.5”
• Max Speed: 7 mph
• Max Range: 6 miles
• Battery: 25.9V, 1.9Ah Lithium-Ion (Each)
• Motor: 250W Hub Motor (Each)
• Charger: 100-240V
• Charging Time: Up to 3 Hours
• Climbing Angle: Up to 10°
• Recommended Age: 13+
• Only use the included charger.
• Plug the charger into the wall before the charging port.
• Never turn on the MotoKicks while they are charging.
• Charge the battery until it is fully charged before using — up to 3 hours.
• Replace the cover over the charging port when done.
• Never leave the MotoKicks charging overnight.
• Charger Indicator Light:
If you can ride a hoverboard, you can ride Jetson MotoKicks.
- Charging
- Charge Complete
Battery Indicator Lights
Charger Indicator Light
Power Button
Important: As a safety precaution, Motokicks will automatically turn off
when they battery charge level goes below 10%.
Follow these 3 simple steps:
1. Turn the MotoKicks off and place them on a lat, level surface.
2. Hold each Power Button for about 5 seconds until the lights
lash and the MotoKicks beep.
3. Restart the MotoKicks by turning them off and then back on.
1. Lean slightly forward to move
forward. You got this!
2. Lean slightly backward to move
in reverse or brake.
3. Turn by leaning to the side as
you ride. Way to go!
4. Step o when the MotoKicks are
at complete stop. Just step back-
wards one foot at a time.
Great riding!
Lights
> 20% 20-30% 30% +
Charge
Percentage
a.
i.
d.
e.
c.
f.
j. k.
b.
h.g.
How it Works
Riding your MotoKicks
Helmet Safety
• Power On: Place on level ground, then turn on each MotoKick by
quick-pressing the Power Button.
• Balance Mode: Gently tilt both MotoKicks and they will self-stabilize.
Master your
MotoKicks!
Scan this for
more riding tips.
Improper positioning:
The forehead is exposed.
A fall could result in serious injury.
Proper positioning:
The forehead is covered
by the helmet.
* Wear a helmet, appropriate clothing, shoes, and safety gear. Avoid clothing
that can get caught into or under the wheels. Closed-toe, lat shoes are
recommended. Wear an ASTM F1492 approved helmet and protective gear to
prevent injury in the event of an accident.
If your Motokicks are not performing as they should, are beeping or
spinning, or feel o balance, their internal balance mechanisms need to
be realigned. This is called “recalibrating.”

Safety Warnings
• Before use, please read the user manual and safety warnings carefully, and make sure you
understand and accept all the safety instructions. The user will be responsible for any loss or
damage caused by improper use.
• Before each cycle of operation, the operator shall perform the preoperation checks speciied
by the manufacturer: That all guards and pads originally supplied by the manufacturer
are in proper place and in serviceable condition; That the braking system is functioning
properly; That any and all axle guards, chain guards, or other covers or guards supplied by
the manufacturer are in place and in serviceable condition; That tires are in good condition,
inlated properly, and have suicient tread remaining; The area that the product is to be
operated should be safe and suitable for safe operation.
• Components shall be maintained and repaired in accordance with the manufacturer’s
speciications and using only the manufacturer’s authorized replacement parts with
installation performed by dealers or other skilled persons.
• Warning against recharging non-rechargeable batteries.
• Don’t allow hands, feet, hair, body parts, clothing, or similar articles to come in contact with
moving parts, wheels, or drive train, while the motor is running.
• This product should not be used by children or persons with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction (IEC 60335-1/A2:2006).
• Unsupervised children should not play with the product (IEC 60335-1/A2:2006).
• Adult supervision is required.
• The rider should not exceed 220 lb.
• Units shall not be operated to perform racing, stunt riding, or other maneuvers, which may
cause loss of control, or may cause uncontrolled operator/passenger actions or reactions.
• Never use near motor vehicles.
• Avoid sharp bumps, drainage grates, and sudden surface changes. Scooter may suddenly stop.
• Avoid streets and surfaces with water, sand, Plasmal, dirt, leaves, and other debris. Wet
weather impairs traction, braking, and visibility.
• Avoid riding around lammable gas, steam, liquid, or dust that could cause ire.
• Operators shall adhere to all of the manufacturer’s recommendations and instructions, as
well as comply with all laws and ordinances: Units without headlights shall be operated only
with adequate daylight conditions of visibility, and; Owners shall be encouraged to highlight (for
conspicuity) using lighting, relectors, and for low-riding units, signal lags on lexible poles.
• Persons with the following conditions shall be cautioned not to operate: Those with heart
conditions; Pregnant women; Persons with head, back, or neck ailments, or prior surgeries
to those areas of the body; and persons with any mental or physical conditions that may
make them susceptible to injury or impair their physical dexterity or mental capabilities to
recognize, understand, and perform all of the safety instructions and to be able to assume the
hazards inherent in unit use.
• Do not ride at night.
• Do not ride after drinking or taking prescription medication.
• Do not carry items when riding.
• Never operate the product barefooted.
• Always wear shoes and keep shoelaces tied.
• Make sure your feet are always placed securely on the deck.
• Operators always shall use appropriate protective clothing, including but not limited to
a helmet, with appropriate certiication, and any other equipment recommended by the
manufacturer: Always wear protective equipment such as helmet, knee pads, and elbow pads.
• Always give way to pedestrians.
• Be alert to things in front and far away from you.
• Do not allow distractions when riding, such as answering the phone or engaging in any
other activities.
• The product cannot be ridden by more than one person.
• When you ride the product along with other riders, always keep a safe distance to avoid
a collision.
• When turning, be sure to maintain your balance.
• Riding with improperly adjusted brakes is dangerous and can result in serious injury or death.
• The brake may become hot while operating, do not touch the brake with your bare skin.
• Applying brakes too hard or too suddenly can lock up a wheel, which could cause you to lose
control and fall. Sudden or excessive application of the brake may result in injury or death.
• If the brake loosens, please adjust with the hexagon wrench, or please contact the Jetson
Care Team.
• Replace worn or broken parts immediately.
• Check whether all safety labels are in place and understood before riding.
• The owner shall allow the use and operation of the unit after a demonstration that such
operators can understand and operate all components of the unit before use.
• Do not ride without proper training. Do not ride at high speeds, on uneven terrain, or on
slopes. Do not perform stunts or turn abruptly.
• Recommended for indoor use.
• Prolonged exposure to UV rays, rain and the elements may damage the enclosure materials,
store indoors when not in use.
California Proposition 65
WARNING:
This product can expose you to chemicals including Chromium (hexavalent compounds), which
is known to the State of California to cause cancer and birth defects or other reproductive
harm. For more information go to:www.P65warnings.ca.gov.
MODIFICATIONS
Do not attempt to disassemble, modify, repair, or replace the unit or any components of the unit without
instruction from the Jetson Care Team. This will void any warranty, and can lead to malfunctions which
may cause injury.
ADDITIONAL OPERATION PRECAUTIONS
Do not lift the product o the ground while it is on and the wheels are in motion. This can result in freely
spinning wheels, which may cause injury to yourself or others nearby. Do not jump on or o the product,
and do not jump while using it. Always keep your feet firmly planted on the foot rest while in operation.
Always check the battery charge before using.
NOTICE OF COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Warning: Changes or
modiications to this unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/ TV technician for help.
Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits.
DISPOSAL OF USED BATTERY
Battery may contain hazardous substances which could endanger the environment and human
health. This symbol marked on the battery and/ or packaging indicates that used battery shall not
be treated as municipal waste. Batteries should be disposed of at an appropriate collection point for
recycling. By ensuring the used batteries are disposed of correctly, you will help preventing potential
negative consequences for the environment and human health. The recycling of materials will help to
conserve natural resources. For more information about recycling of used batteries, please contact your
local municipality waste disposal service.
Loving your ride?
Then be sure to leave a review at ridejetson.com/reviews.
We can’t wait to hear from you!
Stay connected.
Be sure to follow @ridejetson
on social media to learn about fantastic oers,
giveaways, and all the latest Jetson news.
#MakeMoves
Questions? Let us know.
Made in China
Date Code: 09/2022
Document Edition: v3.0
Manufactured in Shenzhen, China
Imported by Jetson Electric Bikes LLC.
P.O. Box 320149, 775 4th Ave #2, Brooklyn, NY 11232
www.ridejetson.com
ridejetson.com/support
ridejetson.com/chat
To exercise your product's
1-year limited warranty
or inquire about warranty
coverage, contact us directly.
US/CANADA: 1-888-976-9904
Care & Maintenance
Warranty
RIDING RANGE
The maximum range per battery charge is 6 miles. However, many factors will
aect how far you can go per charge:
• Riding Surface: A smooth, lat surface will increase riding distance.
• Weight: More weight means less distance.
• Temperature: Ride, charge, and store the MotoKicks above 50°F.
• Maintenance: Timely battery charging after each use will increase
riding distance.
• Speed and Riding Style: Frequent starting and stopping will reduce
riding distance.
CLEANING
To clean the MotoKicks, irst make sure they are turned o and the
Charging Ports are covered. Carefully wipe with a damp cloth, then dry
with a dry cloth. Do not apply water directly to the MotoKicks, as the electrical
and electronic systems may get wet, resulting in a malfunction of the
MotoKicks that could lead to personal injury.
BATTERIES
• Keep away from ire and excessive heat.
• Avoid intense physical shock, severe vibration, or impact.
• Protect from water or moisture.
• Do not disassemble the MotoKicks.
• If there are any issues with the batteries, please contact the Jetson Care Team.
STORAGE
• Fully charge each battery before storing. Each battery should be fully
charged once a month during extended periods of non-use.
• To protect against dust, cover the MotoKicks.
• Store the MotoKicks indoors, in a dry place, and at a temperature
above 50°F.
ONE-YEAR GENERAL LIMITED WARRANTY
All new Jetson products, excluding parts and accessories, are warranted against defects in
materials and workmanship for a period of one year from the date of original retail purchase
when used in accordance with Jetson’s user manuals (refer to ridejetson.com/support).
Under this warranty, you will be able to direct your claims to Jetson even in situations where
you purchased the Jetson Product from one of our authorized retailers.
To read the full terms of our warranty, visit ridejetson.com/warranty.
Jetson's top two riding rules:
Be safe. Have fun!
MotoKicks
Electric Hover Shoes.
A guide for your ride.
IMPORTANT: READ CAREFULLY AND RETAIN FOR FUTURE REFERENCE.
MODEL: JMOTO-BLK
Designed in Brooklyn
Attaching the Training Bar
1. Locate the two screws and side plate on the charging port side of
each MotoKick.
2. Loosen and remove the screws by turning them counterclockwise with a
Phillips-head screwdriver.
3. Use the end of the screwdriver to lift the edge of each side plate up and
remove the plates from the MotoKicks.
4. Store the plates and the 4 removed screws for future use.
5. Position the two MotoKicks on a lat surface so that the sides with the
removed plates are facing each other and the Jetson logo atop each MotoKick
is oriented in the same direction.
6. Align the notches on one end panel of the training bar with the notch spaces
at the top of the area vacated by the side plate. Position the panel so that it is
lush on the side of the MotoKick.
7. Grab 2 of the 4 screws that came with the training bar. Using the screwdriver,
insert and tighten 1 screw into each of the 2 screw holes to secure the training
bar end panel onto the MotoKick.
8. Repeat steps 6 and 7 on the other MotoKick with the other end panel of the
training bar and the remaining 2 screws.
Important: Do not carry the MotoKicks by the training bar.
The training bar add stability for learning and mimics the feeling of
riding a hoverboard.
© 2022, JETSON. ALL RIGHTS RESERVED. Manufactured by JETSON ELECTRIC BIKES LLC.
No portion of this document, including shape, copy, graphics, and design,
may be reproduced or transmitted in any form or by any means.