Agit Wavestorm Junior Stand-Up Paddle Board User manual

Thank You for purchasing a Junior Stand-Up Paddle Board (SUP) and we hope you have fun using your new purchase as much as we’ve enjoyed
developing and testing this Junior SUP.
Stand-Up Paddle Boarding, or in Hawaiian language, Hoe he’e nalu, is an emerging global sport with a Hawaiian heritage. The sport is an ancient form
of surng that began as a method for surng instructors to manage large groups of learner surfers. Standing on the board gave instructors a higher
viewpoint, increasing visibility of what was going on around them - such as an incoming swell or wave. In the early 1960s, The Beach Boys of Waikiki
would stand on their long boards and paddle out with outrigger paddles to take pictures of tourists learning to surf. This is where the term “Beach
Boy Surng”, another name for Stand-Up Paddle Surng, originates.
The sport provides an excellent Core Workout because it requires good core strength to balance and paddle on the board while standing on an
unstable water surface. SUP’ing can be done on oceans, lakes, and rivers. It is gaining in popularity as celebrities are practicing the sport, and
cross-over athletes are training with SUP’s. Many surfers have converted to SUP’ing because of the versatility of this new sport; it can be done
on days when there is surf (waves) or when there are no waves at all.
AGIT Global’s Junior SUP is designed for beginners to advanced SUP’ers alike. Our board dimensions provide good stability on water. The foam
construction of the board, with its 3 Stringer design is very strong yet light-weight and is easy to transport. There is a Built-In Handle near the center
of the topdeck to help carry the board. There is a Fin in the stern for added stability.
The Junior SUP also features our patented ‘Water Barrier Skin’ technology, a thin graphic lm layer covering the board’s top deck, giving protection
from minor scratches, dents and abrasions. It helps keep the SUP looking clean and fresh.
The Paddle can easily be adjusted to accommodate the desired height of most riders. Typically, a rider needs a Paddle extending from the bottom of
their feet to 6-12 inches above their head.
Please read through the instruction manual to properly install the Fins and Leash. We hope you enjoy your new SUP but remember... Always Carefully
Examine Water Conditions in your area, making sure it is clear of Rocks, Reefs, Boats and other Inherent Water Hazards. We highly recommend
wearing only approved US Coast Guard Personal Flotation Devices (PFD) while SUP’ing. SUP’ing can be safer and loads fun when practicing with a
buddy.
ALOHA from the AGIT Global team!

We strongly suggest removing the n
when transporting the board to
prevent damage. Always screw the screw
tightly back into the metal plate on the n
box to prevent the plate from falling out.
Rinse your board with fresh water
after every use to remove dirt, sand, and
salt residue. Pull apart paddle shaft pieces
after each use and rinse with fresh water.
Let dry and leave apart until next use.
Store your board away from direct
sunlight, in a cool, dry location.
If your board has a hole or scratch in
the foam surface, you can purchase any
“Non-Solvent” based glue to repair it.
Spread the glue inside the hole or scratch
and let dry before using. We recommend
using 3M 5200 marine sealant or
Gorilla Glue which can be purchased at
most hardware or drug stores.
LEG LEASH x1
FIN x1
RECOMMEND USER WEIGHT LIMIT NOT
TO EXCEED 120 LBS.
You can also use any “Non Solvent” based
glue to repair side rail seams (where the
slick bottom and foam surface join
together). Before application, test glue on
inconspicuous part of the board. Spread
the glue in seam and let dry before using
the board.
The boards may be slippery when they are
new, if so you can always rub some wet sand
on the deck of the board.
Fins, Leashes and Paddles are available
for purchase. Please call 1-877-673-3622
for more information or visit www.
agit-global.com
1
2
3
4
5
6
7
ADJUSTABLE PADDLE x1

First remove the protective tape,
then remove the screw from the
metal plate.
Insert the screw into the n. Insert Fin into n box by inserting
stainless steel pin of Fin into the
opening of n box, as shown above.
Slide Fin backwards into position,
as shown above.
Screw
Metal Plate
1
Screw
Fin
2
Fin
3
Fin
3.1 Fin
4
3.2
Alternate Insertion:
Slowly slide n into n box from
the top.

Push Fin down, as shown above.
Fin
5Fin
7
6
Screw
Metal Plate
NOTE
We strongly suggest removing the n when transporting the board to prevent damage. Always screw the
screw tightly back into the metal plate on the n box to prevent the plate from falling out.
Attach Fin to metal plate with screw,
as shown above. Then tighten
screw. DO NOT OVER TIGHTEN.
When putting the n in for at
water use, you can put the n
forward. If using it in the surf, put
the n further back in the n box.

Pull Leg Leash Rope through eyelet as shown
above and below.
Pull leg cu through Leg Leash Rope as
shown above.
Pull Leg Leash Rope tight. Installation complete.
12
3
1.1

Determine desired Paddle length. Most riders
prefer Paddle length to be 6-12 inches taller
than the top of their head.
6”-12”
Pull forward the tab on the adjusting
mechanism to free the Locking Pin.
Pull Paddle Handle upward to extend shaft
length to desired height.
Push tab so that Locking Pin securely ts
into hole.
There will be a clicking sound when Locking Pin
is securely tted into desired hole.
Click!
Paddle length can be readjusted by following
same procedure.
1
2
3
4
5
6
NOTE
Pull apart paddle shaft pieces after each use and rinse with fresh water. Let dry and leave apart until next use.

CONTACT CUSTOMER SERVICE IF YOU
HAVE ANY QUESTIONS
1-877-673-3622
AGIT GLOBAL NORTH AMERICA, INC.
14460 Myford Rd, Irvine Ca 92606