JETWAY HBFHP792 Series User manual

User’s Manual
NO. G03-NP792-F
Manual Revision: 1.0
Release Date：July 4, 2018

i
Safety Precautions.............................................................................................................. ii
User’s Notice....................................................................................................................... iii
Package Contents............................................................................................................... iii
Environmental Protection Announcement ....................................................................... iii
Chapter 1 Introduction ..................................................................................................... 1
1-1 General Descriptions............................................................................................ 1
1-2 Specifications ....................................................................................................... 2
1-3 I/O Outlets ............................................................................................................. 3
1-4 Connector Pin Definition ...................................................................................... 5
Chapter 2 Hardware and Installation ............................................................................... 6
2-1 Dimensions and Outlines ..................................................................................... 6
2-2 To Open the Chassis ............................................................................................ 7
2-3 Jumper Settings.................................................................................................... 9
2-3-1 Motherboard Jumper Settings................................................................. 9
2-3-2 Daughter Board Jumper Settings............................................................ 11
2-4 Hardware Installation............................................................................................ 13
2-4-1 To install MSATA Card ............................................................................. 13
2-4-2 To install Wireless LAN Card................................................................... 14
2-4-3 DIM Rail Installation ................................................................................. 17
Chapter 3 Introducing BIOS ............................................................................................. 18
3-1 Entering Setup ..................................................................................................... 18
3-2 BIOS Menu Screen............................................................................................... 19
3-3 Function Keys ...................................................................................................... 19
3-4 Getting Help ......................................................................................................... 20
3-5 Menu Bars ............................................................................................................ 20
3-6 Main Menu ............................................................................................................ 20
3-7 Advanced Menu ................................................................................................... 21
3-8 Chipset Menu ....................................................................................................... 28
3-9 Security Menu ...................................................................................................... 39
3-10 Boot Menu ............................................................................................................ 30
3-11 Save & Exit Menu................................................................................................. 31
APPENDIX ........................................................................................................................... 32
TABLE OF CONTENT

ii
Safety Precautions
 Operate the product according to the correct installation steps and with great care to make sure
safety and comfort using experience. Please refer to the following safety instruction guide to avoid
danger of electric shock or fire. Abide by the previous safety instruction guide to use and maintain
the product and the hard disk to make sure of safe operating environment.
 Please follow the instruction manual for operation guide.
 The appropriate operating temperature ranges from 0 °C–50 °C.
 The operation humidity for this product is 5% to 80% RH.
 To avoid high temperature, please DO NOT overload the maximum power of the external power
supply while the system is consuming high voltage. Be aware of the maximum temperature
allowance of the power supply.
 See to it that the product is not working near the water.
 Always unplug power cable and other hardware cables from the system before cleaning.
 Apply only dry cloth for cleansing the product.
 Make sure that there is no heat source nearby when the product is working.
 Make sure that the thermal louver of the product is not blocked.
 Make sure to remove the power plug from the product when there is a thunder storm.
 Please remove the power plug from the product when you are not going to use the product for a
long time.
 Make sure to set up or use the product on a stable surface.
 Make sure not to drop the product or strike it by any means.
 Make sure not to move the product when the power is on.
 Make sure not to step on the power cables and other cables or rest anything in them..
 Be sure to ground yourself to prevent static charge when installing any internal components. Use a
grounding wrist strap and place all electronic components in any static-shielded devices. Most
electronic components are sensitive to static electrical charge.
 Disconnect the power cord from the Panel PC unit prior to any installation. Be sure both the
system and all external devices are turned off. Sudden surge of power could ruin sensitive
components. Make sure the Panel PC unit is properly grounded. unit
 Do not open the system’s back cover. If opening the cover for maintenance is a must, only a
trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static
electricity. To avoid damaging chips from electrostatic discharge, observe the following
precautions:
 Before handling a board or integrated circuit, touch an unpainted portion of the system
unit chassis for a few seconds. This will help to discharge any static electricity on human
body.
 When handling boards and components, wear a grounding wrist strap available from
most electronic component stores.
 Please contact qualified technician for maintenance or repair.
 Use only accessories and parts that are made by the qualified manufacturer.

iii
User’s Notice
Copyright of this manual belongs to the manufacturer. No part of this manual, including the products
and software described in it may be reproduced, transmitted or translated into any language in any
form or by any means without written permission of the manufacturer.
This manual contains all information required for the utilization of this product to meet the user’s
requirements. But it will change, correct at any time without notice. Manufacturer provides this manual
“as is” without warranty of any kind, and will not be liable for any indirect, special, incidental or
consequential damages (including damages for loss of profit, loss of business, loss of use of data,
interruption of business and the like).
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and they are used only for identification or explanation and to
the owner’s benefit, without intent to infringe.
Package Contents
▶
User’s Manual
▶
DVD for System Utilities
▶
Power Core Cable
▶
Power Adapter
▶
Wi-Fi Antenna
▶
DIN Rail Rack (Optional)
Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. To minimize
pollution and ensure environment protection of mother earth, please recycle.

1
Chapter 1
Introduction
1-1 General Descriptions
Thank you for purchasing the system, a new product developed, designed and
manufactured under leading technical power and consistent dedication to fine
workmanship.
The HBFHP792X series is a rugged fanless automation system, with flexibility to
different configuration through optional expansion solutions, all customized to
meet different demands from our customers.
The system has the following features besides other basic functions:
 WiFi: the Mini PCI-E onboard socket in the board is integrated a with a WiFi
card(802.11 b/g/n) that can act as a mini wireless modem when external
antennas are connected. Different computers in the house can build wireless
connections through the Mini TOP system and take necessary data from it, thus
reducing the complexity in network establishment.
 Giga LAN: The system is integrated with Gigabit LAN network controller with
ACPI management realizing efficient power management for the operating
system.
 USB3.0: Experience Fastest data transfers at 5Gb/s with USB3.0 the new latest
connectivity standard. Built connect easily with next-generation components and
peripherals, USB3.0 transfers data 10x faster and backward compatible with
previous USB2.0 components.
 CPU Usage: The CPU Usage diagram shows a beautiful data curve that
indicates a pretty low CPU usage percentage for video playback of different
formats. GPU performances are excellent as well.
 dB Value: The design of the system takes into consideration the needed quiet
operating environment in the living room and the average dB value is below 26
under normal operation to ensure the tranquility when you are absorbed in film
watching.

2
1-2 Specifications
Main CPU Board
 CPU
 Intel® Bay Trail series SoC processor, depending on different solutions.
 System Memory
 Onboard 2GB DDR3L 1333MHz SO-DIMM
 Network
 2* Intel GbE (MB/Intel i210IT)
 BIOS
 AMI 64Mb Flash ROM
 Storage
 Onboard 1* full-size MSATA slot (for MSATA card)
 Expansion Slot
 Onboard 1* M.2-2230 slot (for WiFi expansion)
I/O System
 Standard I/O of the Motherboard
 1* Lockable 12V DC-in Power Jack
 1* USB 2.0
 1* USB 3.0
 1* VGA
 2* RJ-45 for Gigabit Ethernet
 1* Power Button
 1* Power LED (Green)+ 1* HDD LED (Red)
 Power Source
 FSP 90~240V AC to DC Power Adapter/DC12V-3.3A-40W/LV6
 Expansion I/O of Daughter board
 *Expansion IO l varies from different daughter board solutions. Please refer to
Page-3/4 for more specifc specification.

3
1-3 I/O Outlets
For HBFHP792L Series:
HBFHP792L Series
Standard IO Q’ty
DC-in 1
USB2.0 1
USB3.0 1
VGA 1
RJ-45 LAN 2
Power Switch 1
Expansion IO Q’ty
RJ-45 LAN 4
RJ-45 RS232 COM 1
For HBFHP792U Series:
HBFHP792U Series
Standard IO Q’ty
DC-in 1
USB2.0 1
USB3.0 1
VGA 1
RJ-45 LAN 2
Power Switch 1
Expansion IO Q’ty
RS232 COM 1
USB2.0 4
USB3.0 2
DC-IN
USB 3.0
USB 2.0
VGA
RJ-45 LAN
RJ-45 Type
RS232 COM
RJ-45
LAN
Power On/Off
Power LED
HDD LED
DC-IN
USB 3.0
USB 2.0
VGA
RJ-45 LAN
RS232
COM
Power On/Off
Power LED
HDD LED
USB 2.0
USB 3.0

4
For HBFHP792G Series:
HBFHP792G Series
Standard IO Q’ty
DC-in 1
USB2.0 1
USB3.0 1
VGA 1
RJ-45 LAN 2
Power Switch 1
Expansion IO Q’ty
GPIO Block
(16-pin in+16-pin out)
2
For HBFHP792C Series:
HBFHP792L Series
Standard IO Q’ty
DC-in 1
USB2.0 1
USB3.0 1
VGA 1
RJ-45 LAN 2
Power Switch 1
Expansion IO Q’ty
RS232 COM 3
DC-IN
USB 3.0
USB 2.0
VGA
RJ-45 LAN
GPIO1
Power On/Off
Power LED
HDD LED
GPIO2
DC-IN
USB 3.0
USB 2.0
VGA
RJ-45 LAN
Power On/Off
Power LED
HDD LED
RS232
COM
RS232
COM
RS232
COM

5
1-4 Connector Pin Definition
(1) Motherboard Connector Function
The system comes with NP792-D2 as motherboard, which including the following
basic I/O:
Icon Name Function
DC-in Power Jack
Connector
For user to connect compatible power adapter to provide
power supply for the system.
Power Button Press to turn on/off the system.
USB 3.0 Port
To
connect USB keyboard, mouse or other devices
compatible with USB specification. USB 3.0 ports
supports up to 5Gbps data transfer rate.
USB 2.0 Port
To connect USB keyboard, mouse o
r other devices
compatible with USB specification.
VGA Port
To connect display device that support VGA specification.
RJ-45 LAN Port
This connector is standard RJ-45 LAN jack
for Network
connection.
(2) I/O Connectors Pin Definition
RJ-45 Ethernet Connector
Ethernet connection can be established by plugging one end of the Ethernet cable
into this RJ-45 connector and the other end (phone jack) to a 1000/100/10-Base-T
hub.
The pin assignment for RJ-45 Ethernet LAN connectors are listed as follows:
Pin Definition Pin Definition
L1 MDI0+ L5 MDI2+
L2 MDI0- L6 MDI2-
L3 MDI1+ L7 MDI3+
L4 MDI1- L8 MDI3-
A Active LED (Yellow)
B 100 LAN LED (Green) / 1000 LAN LED
(Orange)

6
VGA Port Connector
The pin assignment for VGA port is listed as follows:
Pin No. 1 2 3 4 5
Definition R G B NC GND
Pin No. 6 7 8 9 10
Definition R-GND
G-GND
B-GND
+5V GND
Pin No. 11 12 13 14 15
Definition NC SDA H-SYN
V-SYN
SCL
Chapter 2
Hardware and Installation
2-1 Dimension and Outlines
* Measure Unit: mm.

7
2-2 To Open the Chassis
1. Place the system on a flat platform upon a cushion. Remove the 4*screws in the marked
spots of system heatsink with a screwdriver. Also please remove the hexagon screw nut
that lock the DC-in power jack.
2. Remove the 4* screws that lock the side
metal plate.
3. Remove the other 4*screws on the
opposite side of the system that lock the
metal panel.
4. With the top heatsink (Step-1) still attached, turn over the system and remove the 4*screws
in the marked spots on the base heat sink.

8
5. Dissemble the front/back panels, side metal plate, and top heat sink from the system.
6. Remove the 4* screws in the marked spots that lock compatible expansion card.
7. Disconnect the expansion card from the
PCIE riser card.
8. The internal view of the motherboard of
the system for further installation.

9
2-3 Jumper Settings
Jumper is a small component consisting of jumper clip and jumper pins. Install
jumper clip on 2 jumper pins to close the pins. And remove jumper clip from 2
jumper pins to open the pins. Diagram 2-1 illustrates how to set up a jumper.
2-3-1 Motherboard Jumper Settings
The system comes with NP792 series IPC board as the motherboard, which has
the following basic jumper settings:
(1) JAT_ATX (3-pin): AT/ATX Mode Function Select
3
3
1
1
JAT_ATX → ATX/AT Mode Select
1-2 Close: ATX Mode Selected(Default);
2-3 Close: AT ModSelected.
*ATX Mode Selected: Press power button to power on after power input ready;
AT Mode Selected: Directly power on as power input ready.
(2) JP1 (3-pin): M2E (M.2 PCIe) Slot VCC Select
3
3
1
1
JP1 → M2E Slot VCC Select
1-2 Close: M2E Slot=3.3V;
2-3 Close: M2E Slot=3.3VSB.
JAT_ATX
JP1

10
(3) Pin (1-2) of JPCLR(4-pin): Clear CMOS Settings
Pin1
2
Pin(1-2) of JPCLR → Clear CMOS Settings
1-2 Open: Normal;
1-2 Closed: Clear CMOS(One Touch).
5
6
Pin1
2
6
5
(4) Pin (5-6) of JPCLR(4-pin): TXE Function Select
Pin1
2
Pin(5-6) of JPCLR → TXE Function Select
1-2 Open: Enable TXE;
1-2 Closed: Disable TXE.
5
6
Pin1
2
6
5
JPCLR
JPCLR

11
2-3-2 Daughter Board Jumper Settings
The system comes with different expansion solutions, which are realized
though different daughter boards. Each has different jumper settings, as the
following shows:
JIOP4INLANG Series
JPCOM1
COM1 RJ-45 COM Port RI Selection
2-4 RS232 RI (Default)
3-4 +5V
6-4 +12V
JPCOM2
COM2 Header RI Selection
2-4 RS232 RI (Default)
3-4 +5V
6-4 +12V
JIOP32GPIO Series
JP_GPIO2
GPIO2 Block VCC Select
1-3 5V
3-5 3.3V
2-4 5VSB
4-6 3VSB
JP_GPIO1
GPIO2 Block VCC Select
1-2 5V
3-4 3.3V
JP2
JP1
COM1
COM2
JP_GPIO1
JP_GPIO2
GPIO1 GPIO2

12
JIOP3COM Series
JPCOM1
COM1 Port RI Selection
2-4 RS232 RI (Default)
3-4 +5V
6-4 +12V
JPCOM2
COM2 Port RI Selection
2-4 RS232 RI (Default)
3-4 +5V
6-4 +12V
JPCOM3
COM3 Port RI Selection
2-4 RS232 RI (Default)
3-4 +5V
6-4 +12V
JIO2U34U21C Series
JPCOM1
COM1 RJ-45 COM Port RI Selection
2-4 RS232 RI (Default)
3-4 +5V
6-4 +12V
JPCOM2
COM2 Header RI Selection
2-4 RS232 RI (Default)
3-4 +5V
6-4 +12V
COM1
COM2
COM3
JPCOM1
JPCOM2
COM1
JPCOM1
COM2
COM2
JPCOM3

13
2-4 Hardware Installation
Remove the screws that lock the back cover to the system from the back side before
hardware installation procedures (refer to 2-2).
2-4-1 To Install MSATA Card
1. Locate the full-size MSATA slot on the
board.
2. Remove the marked screw and use it to
lock MSATA card to the slot in later
installation.
3. Insert the gold-figure side of the
compatible MSATA card into the slot at a
30 degree angle and press down.
4. Lock the card to the board by tightening
up the screw to the marked spot.

14
2-4-2 To Install Wireless LAN Card
Remove the screws that lock the cover to the system before installing Wi-Fi card
procedures (refer to 2-2).
Please refer to the following instructions for the installation of the wireless LAN card
into M.2 PCIe slot.
1. Locate the M.2. PCIe slot on the board. 2. Remove the marked screw and use it to
lock compatible Wi-Fi card to M.2. PCIe
slot in later installation.
3. Insert the gold-figure side of compatible
card into M.2. PCIe slot and press down.
See to it that the golden-figure side is
fully inserted into the slot.
4. Lock the card to the board by tightening
up the screw to the marked spot.

15
5. Find the antenna wires from the
accessories package.
6. In the case that the metal hats on the end
of the antenna wires are sealed by
acetate tape, tear it off to find metal hats
of Wi-Fi antenna wire.
7. Press the metal hats of the antenna string
end to the antenna slots on the card as
showed.
8. There are 3 reserved holes in the front
panel for WiFi antenna installation.
Remove the dust plug from the spot you
choose to install antenna head.
9. Internal View: Put the above metal gasket into the antenna head at first, and then push
this antenna head into the back side of the rear panel.

16
10. External View: Put the metal ring into the antenna head, and then lock the antenna
head to the front side of the rear panel the above hexagonal bolt.
11. The IO panel with antenna head installed.
12. Connect the external Wi-Fi receiver
antenna to the antenna head on the
panel.