Jimmy Styks THRESHER User manual

OWNER’S GUIDE
GUIDE DU PROPRIÉTAIRE
MANUAL DEL PROPIETARIO
オーナーズガイド
使用指南

2
READ THIS IMPORTANT INFORMATION BEFORE USING
YOUR STAND-UP PADDLEBOARD
FOR WARRANTY INFORMATION, PARTS/ACCESSORIES, CALL 1-800-370-0745
OR CONTACT US THROUGH OUR WEB SITE, WWW.JIMMYSTYKS.COM
DISREGARDING ANY OF THE SAFETY PRECAUTIONS AND INSTRUCTIONS CONTAINED IN THE OWNER’S
MANUAL AND/OR ON THE PRODUCT MAY RESULT IN INJURY, INCLUDING THE POSSIBILITY OF DEATH.
- REVIEW THE WEIGHT CAPACITY LIMITATIONS OF THIS BOARD AND NEVER EXCEED THEM.
WWW.JIMMYSTYKS.COM
- ALWAYS WEAR A COAST GUARD APPROVED PERSONAL FLOTATION DEVICE (PFD).
- NEVER GO PADDLE BOARDING IN SEVERE WEATHER OR WATER CONDITIONS THAT MIGHT AFFECT
YOUR ABILITY TO STEER THE BOARD OR RETURN TO SHORE.
- NEVER ALLOW MINORS TO USE THIS BOARD WITHOUT ADULT SUPERVISION.
- NEVER CONSUME ALCOHOL OR ANY OTHER SUBSTANCES THAT MAY IMPAIR YOUR COORDINATION,
JUDGEMENT, OR ABILITY TO SAFELY PADDLE THE BOARD.
- NEVER USE THIS BOARD BEYOND YOUR SKILLS OR ABILITY.
- NEVER USE THIS PRODUCT AFTER SUNSET, BEFORE DAWN OR AT ANY TIME IN POOR LIGHTING.
- CHECK LOCAL LAWS AND REGULATIONS REGARDING PROPER AND SAFE USE OF THIS PRODUCT.
- NEVER USE THE VALVE WRENCH TO DEFLATE AN INFLATED BOARD.
- PRESSURE GAUGE WILL ONLY REGISTER PRESSURE ABOVE 10 PSI.
- DO NOT INFLATE SUP ABOVE 15 PSI.
- KEEP CLEAR OF SHARP OBJECTS AND/OR HEAT PRODUCING OBJECTS.

SECTION 1
MODEL, FEATURES AND ACCESSORIES PAGES 4 - 5
SECTION 2
CARE AND MAINTENANCE PAGES 6 - 7
SECTION 3
HIGH PRESSURE PUMP PAGES 8 - 9
SECTION 4
SUP INFLATION AND DEFLATION PAGES 10 - 11
SECTION 5
FINS AND INSTALLATION PAGES 12 - 13
SECTION 6
PADDLE ASSEMBLY & SIZING PAGES 14 - 15
SECTION 7
TRANSPORTATION TIPS PAGE 16
SECTION 8
MINOR REPAIRS PAGE 17
SECTION 9
LIMITED WARRANTY INFORMATION PAGE 18
TABLE OF CONTENTS
3
QUESTIONS/COMMENTS:
1-800-370-0745

4
SECTION 1
FOR WARRANTY INFORMATION, PARTS/ACCESSORIES, CALL 1-800-370-0745
OR CONTACT US THROUGH OUR WEB SITE, WWW.JIMMYSTYKS.COM
FEATURES
BUNGEE TIE-DOWN SYSTEM
HANDLE
AIR VALVE
LEASH PLUG
FIN BOX
PRODUCT SERIAL NUMBER
RIDER SKILL
ENVIRONMENT
DURABILITY
PERFORMANCE
RIDER COMPATIBILITY
NOVICE PRO
FLATWATER SURF
FRAGILE RUGGED
STABILITY AGILITY
MAX
LIMIT
PSI
15
270
POUNDS
SPECIFICATIONS
LENGTH
WIDTH
THICKNESSS
ROCKER (N)
ROCKER (T)
10’8” (325 CM)
31” (78.7 CM)
5.9” (15 CM)
4” (10.2 CM)
0” (0 CM)
INFLATABLE SUP

MODEL, FEATURES AND ACCESSORIES
5
QUESTIONS/COMMENTS:
1-800-370-0745
ACCESSORIES
A. 1X ADJUSTABLE TRAVEL PADDLE
B. 1X STABILIZER FIN + HARDWARE
C. 1X PUMP, HOSE & GAUGE
D. 1X 10 FT. COIL LEASH
E. 1X REPAIR KIT + VINYL PATCHES
F. 1X VALVE WRENCH
G. 1X BOARD TOTE
*PACKAGED ACCESSORIES MAY VARY BY RETAILER.
A. B.
C.
D. E. F.
G.
OR
OR

6
SECTION 2
FOR WARRANTY INFORMATION, PARTS/ACCESSORIES, CALL 1-800-370-0745
OR CONTACT US THROUGH OUR WEB SITE, WWW.JIMMYSTYKS.COM
Direct sunlight can damage a board if left exposed for a period of time. Heat can cause the air
inside the board to expand beyond the internal pressure limits of the board. Keep your
board in an area with good air ow and circulation. Leaving your board in a vehicle during
the day (closed or open) elevates the risk for heat related damages.
KEEP IN A WELL VENTILATED, SHADED
AREA WHEN NOT IN USE.
Max pressure is 15 psi. Do not overinate. If inated in cooler early morning temperatures,
inate closer to the lower end of optimal ination range. Inating at a lower psi will allow for
pressure expansion as the outside temperature warms during the course of the day.
OPTIMAL INFLATION IS 12-15 PSI.
MAX PRESSURE IS 15 PSI.
OVERINFLATING YOUR PADDLE BOARD
OR IMPROPER INFLATION/DEFLATION IS
NOT COVERED UNDER WARRANTY!
RINSE SAND AND SALTWATER DEPOSITS
FROM YOUR BOARD AFTER USE.
Sun, sand and saltwater will degrade any man-made material over time. Rinse off sand
and saltwater deposits from your paddle board with fresh water and store in a cool, dry
environment after each use.

CARE AND MAINTENANCE
7
QUESTIONS/COMMENTS:
1-800-370-0745
REGISTER YOUR JIMMY STYKS®
Register your JIMMY STYKS®SUP online to
activate your product warranty.
jimmystyks.com/registration.php
DO NOT STORE YOUR BOARD IN A BOARD
BAG FOR EXTENDED PERIODS OF TIME.
Board bags are intended for transportation protection, not full time storage. Prolonged
storage of a wet board in a wet board bag will have adverse effects on the nish of your
board, leading to the possibility of mold, and osmotic blisters. Storing your board in a board
bag is not the same as placing it in the shade. Board bags will collect heat and potentially
overheat your board.

8
SECTION 3
FOR WARRANTY INFORMATION, PARTS/ACCESSORIES, CALL 1-800-370-0745
OR CONTACT US THROUGH OUR WEB SITE, WWW.JIMMYSTYKS.COM
Your JIMMY STYKS® inatable paddleboard
includes a high pressure pump in one of two
styles: STANDARD or DUAL-ACTION.
The STANDARD pump includes an air hose
and stand-alone pressure gauge. The
STANDARD pump has a volume capacity of
2500 cm³ and can exert 1 BAR (15 PSI) of air
pressure per pump.
The DUAL-ACTION pump includes an airhose
and built-in pressure gauge. The DUAL-
ACTION pump has a volume of capacity of
2000 cm3 and can exert 2 BAR (29 PSI) of
air pressure per pump. For added efciency,
engage the action selector to “DOUBLE
ACTION” and exert an equal volume of air on
both up and down strokes of the pump.
HIGH PRESSURE PUMP
PUMP
PUMP
ACTION
SELECTOR
PRESSURE
GAUGE
PRESSURE GAUGE
AIR HOSE
AIR HOSE
STANDARD PUMP
DUAL ACTION PUMP
ACTION SELECTOR

HIGH PRESSURE PUMP
9
QUESTIONS/COMMENTS:
1-800-370-0745
REGULARLY MAINTAIN THE PUMP.
Both pump models require lubrication to maintain life and efciency. To lubricate, open
the top and spread a thin layer of oil or grease on the gasket and tube. Additionally, the
STANDARD pump features an air lter inside the top. Periodically clear the air lter of
debris for best operation.
CLEAN AIR FILTER
LUBRICATE
TOP EDGE &
INSIDE OF TUBE
LUBRICATE
TOP EDGE &
INSIDE OF TUBE
STANDARD PUMP DUAL ACTION PUMP
NEED REPLACEMENT PARTS?
Visit our replacement parts store online:
www.jimmystyks.com/parts.html or
call toll-free: 1-800-370-0745.

10
SECTION 4
FOR WARRANTY INFORMATION, PARTS/ACCESSORIES, CALL 1-800-370-0745
OR CONTACT US THROUGH OUR WEB SITE, WWW.JIMMYSTYKS.COM
Attach pressure gauge to pump (STANDARD pump
only). Begin with pressure gauge dial facing the
ground and twist clockwise 180 degrees until dial
is securely fastened and facing upward.
Fasten air hose to pressure gauge.
Locate the air valve on tail section of the board deck
and open valve cap.
Turn the colored valve pin counter-clockwise to the
“UP” position. The valve pin will prevent air from
escaping when in the “UP” position.
Connect air hose to air valve and twist 90oto secure
the connection.
Inate to 12-15 psi.
Disconnect air hose from valve and close valve cap.
Open valve cap.
Depress colored valve pin and turn clockwise to lock
the pin in the “DOWN” or open position.
Allow air to freely escape inatable SUP for a few
minutes.
Beginning at the nose, tightly roll up Inatable SUP to
force remaining air through the air valve.
SUP INFLATION
SUP DEFLATION
DOWN
FOR
DEFLATION
UP
FOR
INFLATION
STANDARD PUMP
ONLY
1.
1.
2.
3.
4.
2.
3.
4.
5.
6.
7.

SUP INFLATION AND DEFLATION
11
QUESTIONS/COMMENTS:
1-800-370-0745
Verify the valve pin is in the “UP” position. “UP” keeps air in. “DOWN” allows air out.
Verify the air hose is securely fastened to the air valve.
The air valve may be loose. Refer to “VALVE TIGHTENING” below.
Back-ow air pressure does not reach measureable levels until the paddleboard is
substantially inated. If the pressure guage is not registering a value, the board may
still require more ination until a pressure reading occurs.
Check for tears and/or cracks. This is best performed in water. Submerge the sup
and look for streams of air bubbles. If a large body of water is not available, try a
spray bottle lled with water and dish soap. Spray the board along the seams and
look for billowing soap bubbles. If a tear/hole is located, refer to “INFLATABLE SUP
REPAIRS” in this manual.
If none of these tips resolve the issue, contact us online through our live chat or
email at www.jimmystyks.com.
SUP NOT INFLATING or AIR ESCAPING SUP WHILE INFLATING
INFLATION TROUBLE SHOOTING
VALVE TIGHTENING
Occasionally, the valve on your inatable SUP may become
loose. If the valve ange freely spins when opening the
valve cover or you detect air leaking from the valve area,
tightening may be required. Using the included valve
wrench, tighten valve in a clockwise motion until hand tight.
NEVER USE THE VALVE
WRENCH WHEN SUP
IS PRESSURIZED.
VALVE WRENCH

PIN-MOUNT style n sets includes a
center stabilizer n and either a connected
attachment pin or seperate barrel/screw set.
We recommend removing ns after each use to
prevent damage to the n, n clamp and board.
PIN MOUNT FINS
FIN INSTALLATION
12
SECTION 5
FOR WARRANTY INFORMATION, PARTS/ACCESSORIES, CALL 1-800-370-0745
OR CONTACT US THROUGH OUR WEB SITE, WWW.JIMMYSTYKS.COM
Insert fin, front first then lower into place
until flush against bottom of fin clamp.
Insert pin through the n clamp eyelet. If
using a barrel/screw attachment, insert
screw through n clamp eyelet and secure
by tightening the barrel. Verify the n is
securly attached to the board and connecting
string is securely attached to the n before
entering water.
1. 2.
STABILIZER FIN
ATTACHMENT
PIN
FIN SCREW
AND BARREL

FIN INSTALLATION
13
QUESTIONS/COMMENTS:
1-800-370-0745
FIN BOX style n sets includes a center
stabilizer n, screw/plate set and n key. We
recommend removing ns after each use to
prevent damage to the n, n box and board.
FIN-BOX STYLE FINS
FIN INSTALLATION
With the mounting screw and plate loosely
attached to the fin, insert fin into the fin
box channel. Start with the back-side first
by sliding the rear horizontal pins into the
track channel.
Slide the n completely into the n box
channel and tighten the mounting screw
using the supplied n key.
1. 2.
PLATE
SCREW
STABILIZER FIN
FIN KEY
FIN SCREW
AND PLATE

14
SECTION 6
FOR WARRANTY INFORMATION, PARTS/ACCESSORIES, CALL 1-800-370-0745
OR CONTACT US THROUGH OUR WEB SITE, WWW.JIMMYSTYKS.COM
PADDLE ASSEMBLY
The Inatable SUP includes our JS Adjustable Travel Paddle.
For carrying convenience, the paddle can be separated into
two smaller halves. Our JS WATER GEAR adjustable clamp
allows for non-permanent sizing on-the-go.
When connecting the two shafts of the paddle, make sure
that the “Jimmy StyksM” logo side of the blade is aligned
with the adjustable clamp lever.
BE CAREFUL TO NOT
PINCH FINGER TIPS
WHEN ASSEMBLING
THE PADDLE.
WATER MAY ENTER
THE SHAFT OF THE
TRAVEL PADDLE
CAUSING THE
PADDLE TO SINK.
JIMMY STYKS®
LOGO
ADJUSTABLE
CLAMP LEVER

PADDLE ASSEMBLY & SIZING
15
QUESTIONS/COMMENTS:
1-800-370-0745
Extending beyond the maximum extension limit can result in permanent damage to the adjustment clip
while paddling. We recommend paddle to be rinsed with fresh water after every use and upper shaft
removed for drying.
DO NOT EXTEND UPPER SHAFT BEYOND
24 IN (61CM).
TM
8 - 10 IN. (20.3 CM - 25.4 CM)
JS ADJUSTABLE PADDLE SIZING
MAX.
EXTENSION
24 IN.
(61 CM)

16
TRANSPORTATION TIPS
SECTION 7
FOR WARRANTY INFORMATION, PARTS/ACCESSORIES, CALL 1-800-370-0745
OR CONTACT US THROUGH OUR WEB SITE, WWW.JIMMYSTYKS.COM
Inatable SUPs are designed to compact for convenient storage & travel. Due to a lack
of weight when inated, they will travel poorly if strapped to a vehicle rooftop. Damages
incurred by improper transport are not covered by the manufacturer’s warranty!
When transporting, be sure to clear any sharp objects. Punctures are not covered by the
manufacturer’s warranty!
Keep clear of any heat producing items such as camp stoves, propane lamps, etc. Damages
resulting from heat are not covered by the manufacturer’s warranty!
Allow your Inatable SUP to completely dry before tightly rolling for packing. Excess
moisture may cause mildew and/or mold damage.
DO NOT TRANSPORT AN INFLATED STAND
UP PADDLE BOARD ONTOP OFAVEHICLE.
The included board tote is intended for Inatable SUP and Inatable SUP accessories
only. Additional items added to the board tote may exceed weight capacity and result in
damages to the tote, shoulder straps and/or carry handle.
When completely packed, an inatable SUP and its accessories can get rather heavy. Make
sure to never carry more than is comfortable for you in one trip. Always use proper lifting and
carrying techniques to avoid straining muscles.
For maximum comfort when carrying the board tote, wear both shoulder straps to evenly
distribute the carry weight. Tighten the shoulder straps to reduce slack and to avoid tote
contents from resting on the back of the legs.
NEVER CARRY MORE THAN YOU CAN
HANDLE COMFORTABLY.

17
QUESTIONS/COMMENTS:
1-800-370-0745
MINOR REPAIRS
SECTION 8
NEED REPLACEMENT PARTS?
Visit our replacement parts store online:
www.jimmystyks.com/parts.html or
call toll-free: 1-800-370-0745.
1.
2.
3.
4.
5.
6.
7.
REPAIR KIT
CONTAINER
CEMENT
PVC/POLYESTER
PATCHES X 2
DIRECTIONS FOR USE
BEFORE YOU START
Completely deate paddle board.
Thoroughly clean the surface around the leak and the matte side of the PVC/Polyester patch with
rubbing alcohol. Both surfaces must be free of moisture, oil and debris.
Open the cement tube by breaking the tube seal using the outside of the tube cap.
Apply cement carefully and evenly to both paddle board surface and matte side patch surface.
Avoid contact with skin & eyes. Avoid breathing cement vapors.
Allow cement on both board and patch to dry to the touch. Once dry, reapply a very thin layer of
cement around the perimeter of the patch.
Once cement on both board
and patch becomes tack-
free, apply patch to board
and rmly work out any
trapped air bubbles.
Allow 8 hours for cement
to cure before inating
paddleboard.
Prepare the following items:
Latex Gloves (Pair)
Isopropyl Alcohol (Rubbing Alcohol)
Clean Cloth
Cement Applicator (Brush, Popsicle® stick, etc.)
Emergency Repair Kit Contents (Cement + Patches)
WEAR LATEX GLOVES TO AVOID
SKIN IRRITATION.

18
PRODUCT WARRANTY
SECTION 9
FOR WARRANTY INFORMATION, PARTS/ACCESSORIES, CALL 1-800-370-0745
OR CONTACT US THROUGH OUR WEB SITE, WWW.JIMMYSTYKS.COM
JIMMY STYKS®OFFERS A LIMITED 365 DAY WARRANTY
AGAINST DEFECTS IN MATERIALS AND WORKMANSHIP.
TERMS OF WARRANTY:
Your JIMMY STYKS® product is guaranteed to be free of defects in material and workmanship for a period
of no more than 365 days from the date of purchase. If the product does not conform to the warranty,
JIMMY STYKS®, at its discretion will issue a new, like new, or similar model product, excluding any
shipping charges. Warranty extends to original purchaser only and is non-transferable. Sales receipt and
original packaging materials are required.
WARRANTY:
JIMMY STYKS® will make every effort to produce boards to the highest quality and standards in the
industry. We do quality checks in our factories in Asia and in our warehouses in North America in an effort
to guarantee each board’s quality before shipping. Because of the nature of surng and paddle boarding
we cannot warranty the performance of any board or shape for individual riders and varying levels of
skills and abilities. Furthermore, we cannot guarantee against damage or breakage and cannot protect or
warranty against circumstances outside of our control. In the event of a new board being removed from
a box and not in good condition please contact the ofce for resolution. You will be asked for a copy of
your sales receipt and photos of the damage in question, as well as original packaging material to verify
if damage was due to shipping. If it is deemed a manufacturing or material aw, we will issue an RMA
number. This number along with the damaged product will need to be returned to the closest warehouse
(Vancouver or Huntington Beach) at customer’s expense. Upon physical review, JIMMY STYKS® will make
its nal determination as to the nature of the damage or aw and issue a replacement product (model
depends on availability), or store credit. Shipping will be the responsibility of the customer. We are not
responsible for damage or defects once the board has been used. Damage is dened as impact with any
object or material, damage due to dropping, loading, unloading, or transport, alterations or modications,
repairs, natural disasters, res, temperatures below 4.4 oC (40 oF), or above 43oC (110 oF), any further use
of a board once a claim has been reported, transport or storage of a board with a closed air valve, use of
a board in the water with a loose or removed air valve, failure to clean and service air vent valve, storage
of a board in extremely hot or humid conditions including a wet or damp board bag.
RETURNSAND EXCHANGES:
JIMMY STYKS® will exchange any new,
unused product for company credit providing
it is accompanied by an original sales receipt
and all original packaging. This will not include
any shipping charges or expenses. Product
must be in new condition and will be subject
to the inspection of staff.
NEED TO FILE A
WARRANTY CLAIM?
Submit a warranty form
and photos online:
www.jimmystyks.com/
warranty.php

19
QUESTIONS/COMMENTS:
1-800-370-0745

2
VEUILLEZ LIRE LES RENSEIGNEMENTS IMPORTANTS SUIVANTS
AVANT D’UTILISER VOTRE PLANCHE À PAGAIE
POUR DES RENSEIGNEMENTS SUR LA GARANTIE, LES PIÈCES OU LES ACCESSOIRES,
APPELEZ AU 1 800 370-0745 OU COMMUNIQUEZ AVEC NOUS SUR NOTRE SITE WEB
WWW.JIMMYSTYKS.COM
LE NON-RESPECT DES PROCÉDURES ET DES CONSIGNES DE SÉCURITÉ CONTENUES DANS LE
MANUEL DU PROPRIÉTAIRE ET/OU FIGURANT SUR LE PRODUIT PEUT CAUSER DES BLESSURES,
INCLUANT LA MORT.
-CONSULTEZ LES CAPACITÉS DE POIDS MAXIMALES DE CETTE PLANCHE SUR LE SITE JIMMYSTYKS.
COM ET ASSUREZ-VOUS DE NE JAMAIS LES DÉPASSER.
-PORTEZ TOUJOURS UN GILET DE SAUVETAGE APPROUVÉ PAR LA GARDE CÔTIÈRE.
-N’UTILISEZ PAS LA PLANCHE À PAGAIE LORSQUE LES CONDITIONS MÉTÉOROLOGIQUES OU SUR
L’EAU SONT DIFFICILES ET LORSQU’ELLES RISQUENT DE NUIRE À VOTRE CAPACITÉ DE MANŒUVRER
LA PLANCHE OU DE RETOURNER SUR LA RIVE.
-NE LAISSEZ JAMAIS DES MINEURS UTILISER CETTE PLANCHE SANS LA SUPERVISION D’UN ADULTE.
-NE CONSOMMEZ JAMAIS D’ALCOOL OU TOUTE AUTRE SUBSTANCE POUVANT NUIRE À VOTRE
COORDINATION, JUGEMENT OU CAPACITÉ D’UTILISER LA PLANCHE DE MANIÈRE SÉCURITAIRE.
-N’UTILISEZ JAMAIS CETTE PLANCHE AU-DELÀ DE VOS COMPÉTENCES OU DE VOS HABILETÉS.
-N’UTILISEZ JAMAIS CE PRODUIT APRÈS LE COUCHER DU SOLEIL, AVANT LE LEVER DU SOLEIL OU EN
TOUT TEMPS LORSQUE L’ÉCLAIRAGE EST INSUFFISANT.
-CONSULTEZ LES LOIS ET LES RÈGLEMENTS LOCAUX CONCERNANT L’USAGE APPROPRIÉ ET
SÉCURITAIRE DE CE PRODUIT.
-N’UTILISEZ JAMAIS LA CLÉ POUR VALVE POUR DÉGONFLER UNE PLANCHE GONFLÉE.
-LE MANOMÈTRE (INDICATEUR DE PRESSION) INDIQUERA SEULEMENT UNE PRESSION DE PLUS DE 10 PSI.
-NE GONFLEZ PAS LA PLANCHE À PAGAIE À UNE PRESSION DE PLUS DE 15 PSI.
-GARDEZ LA PLANCHE À L’ÉCART DE TOUT OBJET POINTU OU TRANCHANT ET/OU DE TOUT OBJET
PRODUISANT DE LA CHALEUR.
Table of contents
Languages:
Other Jimmy Styks Sport & Outdoor manuals
Popular Sport & Outdoor manuals by other brands

GLD Products
GLD Products VIPER 850 manual

Lifetime
Lifetime POWER LIFT 90682 Assembly instructions

Franklin
Franklin FLYBACK PITCH RETURN Assembly instructions

Bestway
Bestway Bouncetastic Bouncer owner's manual

Rave Sports
Rave Sports RAVE EZ Set Ice Rink-200 owner's manual

Sport-thieme
Sport-thieme 115 6414 Assembly instructions