JL Audio STEALTHBOX SB-POL-SLINGSPKR/M770 User manual

Enclosure Type: Sealed
Driver Type: M770-TCS-SG-TB
Nominal Impedance: 4 ohms
Continuous Power Handling: 100 watts (RMS method)
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your
authorized JL Audio dealer. The installation professionals employed by your
dealer have the necessary tools and experience to disassemble and reassemble
your vehicle properly. If you prefer to perform your own installation, please read
this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely
vital that the Stealthbox®be properly mounted to the vehicle
according to these instructions. Failure to mount the enclosure
properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the
enclosure caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a
collision or sudden deceleration.
INSTALLATION
DIFFICULTY:
ESTIMATED TIME:
1 HOUR
Continued on Next Page
15
OUT
OF
SB-POL-SLINGSPKR/M770 INSTR_SKU# 011484
INSTALLATION GUIDE
for the
SB-POL-SLINGSPKR/M770
SKU# 94636
2017-Up Polaris Slingshot

INCLUDED HARDWARE
Continued on Next Page
Page 2 • JL Audio, Inc., 2017
SB-POL-SLINGSPKR/M770 INSTR_SKU# 011484
BOM ID Qty SKU Description
1 2 153853 M6 - 1 x 25mm Hex Drive Flanged Button Head Screw
2 2 153846 Kick Panel Bracket
3 4 153852 1/4 - 20 x 7/8” Hex Drive Flat Head Screw
4 4 153902 Stainless Steel Cushion Clamp
5 8 153729 1/4 - 20 x 1” Serrated Flange Head Bolt
- 1 150249 Foam Tape (not shown)
Note: For optimum performance, JL Audio recommends applying the included Foam Strips (or sound damping material) to surrounding plastic panels to reduce unwanted vibrations.
123
4 5
(hardware pictured for one)

POWER RECOMMENDATION
JL Audio recommends high quality ampliers such as the JL Audio MX280/4. The diagram below shows the recommended crossover settings for the MX280/4. For a detailed description of the ampli-
er settings, consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.
CONNECTIONS
Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your
Stealthbox® amplier. Other kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for
both channels of the amplier. JL Audio recommends using 12 AWG speaker wire for subwoofers such as our XC-BCS12-25.
Continued on Next Page
Page 3 • JL Audio, Inc., 2017
SB-POL-SLINGSPKR/M770 INSTR_SKU# 011484

Page 4 • JL Audio, Inc., 2017 Continued on Next Page
STEP 8
Pass a 1/4 - 20 x 1” Serrated Flange Head Bolt
through the hole in the Stainless Steel Cushion
Clamp, into the threaded insert in the speaker
pod. Do not fully tighten at this time.
Repeat the process for the second Stainless
Steel Cushion Clamp.
STEP 7
Align the speaker pod with the two lower
sections of the roll bar and the upper section
of the roll bar, as shown.
STEP 6
Lift the speaker pod into position, wrapping
the Stainless Steel Cushion Clamps around the
roll bar, as shown.
STEP 5
Place the speaker pod in the vehicle. Connect
the speaker cable to the terminal cup on the
back of the speaker pod.
STEP 4
Route speaker cable to the speaker pod
location, between the two lower sections of
the roll bar, as shown.
STEP 3
Align the holes in the Kick Panel Bracket with
the threaded inserts in the opposite side of the
speaker pod, and secure with a pair of 1/4 - 20 x
7/8” Hex Drive Flat Head Screws.
STEP 2
Place the speaker pod face down on a flat
surface. Pass a 1/4 - 20 x 1” Serrated Flange
Head Bolt through a hole in each Stainless
Steel Cushion Clamp. Thread an assembly into
each of the two upper threaded inserts on the
side of the speaker pod, as shown.
Align the other holes in the Stainless Steel
Cushion Clamps with the lower threaded
inserts, and fully tighten the bolts.
STEP 1
Pictured is the hardware needed for each
speaker pod. The following steps show the
installation procedure for the driver’s side only,
but the procedure is the same for both sides.
SB-POL-SLINGSPKR/M770 INSTR_SKU# 011484

Page 5 • JL Audio, Inc., 2017
MID/HIGH FREQUENCY DRIVER FITMENT
SB-POL-SLINGSUBD/10W3v3 and SB-POL-SLINGSUBP/10W3v3 Stealthbox® subwoofer enclosures are also
available for your vehicle. Each weatherproof enclosure is designed for a perfect t and houses a premium
JL Audio subwoofer.
SB-POL-SLINGSUBD/10W3v3
SKU# 94637 (4 W) & 94638 (2 W)
SB-POL-SLINGSUBP/10W3v3
SKU# 94639 (4 W) & 94640 (2 W)
All specifications are subject to change without notice. “JL Audio®”and the JL Audio logo,“Stealthbox®” and the Stealthbox logo, and “How we play®” are registered trademarks of JL Audio, Inc.
“Ahead of the Curve” and its respective logo are trademarks of JL Audio, Inc.
Printed in USA • ©2017 JL Audio, Inc. • For more detailed information please visit us online at www.jlaudio.com.
[phone]
www.jlaudio.com
JLA-SKU# 011484 • ver. 08.14.2017 • 10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
CONGRATULATIONS!
You have completed the installation for this model! Enjoy your new Stealthbox®!
SB-POL-SLINGSPKR/M770 INSTR_SKU# 011484
®
STEP 10
Pictured is the driver’s side speaker pod fully
installed.
Repeat the installation process for the
passenger side speaker pod.
Note: For optimum performance, we
recommend applying the included Foam Strips
(or sound damping material) to surrounding
plastic panels to reduce unwanted vibrations.
STEP 9
Align the hole in the Kick Panel Bracket with
the factory hole in the roll bar tab. Pass an M6
- 1 x 25mm Hex Drive Flanged Button Head
Screw through the Kick Panel Bracket, thread it
into the factory hole, and fully tighten.
Fully tighten the two 1/4 - 20 x 1” Serrated
Flange Head Bolts.