JLR Gear Smart Gear User manual
'gear INDOOR/OUTDOOR
WIRELESS
WEATHER STATION
USER MANUAL
The lndoor/Outdoor Wireless Weather
Statron features weather forecast. indoor and outdoor
temperature/humidity as well as heat index and dew point.
on an easy to read drsplay. Use the integrated LJSB
charging port to charge your devices when the Weatner
Station is plugged into a power ouilet.
LCD
SqEl
Co,lrcl
Sufbos m
Hol€s
Remote Sonor TEnsmifrer
i8:i,!."'rn AcwarrPrus
#
-ry NW
Fo d.ut Stand Positon
A sarerY TNFoRMATToN
Please read and understand this entire manual before attempting to assemble, operate or install the
product. lf you have any questions regarding the product, please call customer service at 1-800-254-01 1 1.
WARNING:
DO NOT mix old and new batteries. DO NOT mix alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium) batteries. DO NOT dispose of batteries in fire. Batteries may explode or leak.
Please dispose of batteries properly. Remove batteries for long term storage. Batteries could leak
causing corrosion.
BATTERY INSTALLATION
IN DOOR/OUTDOOR WIRELESS WEATHER STATION
e,en cve ::e cat:ery ccver on ihe bacK o: :he Wrie,ess \.4/eather
Siatron. Insert 3 MA 1.5V battenes inot included) as indicateo by the
polarity symbols (+ and -) see Fig. A. Replace the battery cover.
I
$[rEtr o
Cr,.0
ff-il1
lhEil
irilui
\-/
SETUP STEP BY STEP INSTRUCTIONS
STEP 1
OPTIONAL BATTERY OPERATION: lnsert 3 NEW AAA batteries (not
included) following the instructions for battery installation. Observe the
mnect polarity (+ and -). The Wireless Weather Station will light up
and show indoor temperature, humidity and channel 1.
STEP 2
lnsert the S-volt a/c power adapter into the adapter port on the side of
the Wireless Weather Station (Fig. C). Plug the a/c power adapter into
a wall outlet for continuous backlight (ON/OFF), and dimmer feature.
Backlight will illuminate for 8 seconds when using only battery power
with a press/release of the SNOOZE/LIGHT button.
STEP 3
Ensure that the transmitter is within 10 feet of the Weather Station.
lnsert 2 NEW AAA 1.5V batteries (not included) into Remote Sensor
Transmitter.Observethecori"ectpolarity(+and-) see Fig.B.TheTXswitchissetto
Channel 'l by oefault, see Fig B. Confirm channei 1 is selected. Within 3 minutes the Weather Station will
beep and then show reaoings in the outdoor tenrperaiure area on the Wrreless Weather Station LCD.
Note: Use Alkaline batteries (or Lithium for temperatures below -20"F/-28.8"C).
POSITIONING THE REMOTE SENSOR TRANSMITTER
Once the Wireless Weather Station shows the outdoor temperature, place it and ihe transmitter in the
desireci locations and waii approximately 1-hour before perrnanently mounting the transmitter to ensure
that there is proper reception. TIre transmitter should be mounted vertically, in a shaded, protected area,
at least 6 feet from the ground lo avord damage anci ensure accurate readings. The transmitter is water
resistant. not waierproof and should not be placed where it will become submerged in water or subject to
standing water or snow.
WALL MOUNT
Choose a shaded location (under an overhang) for the transrnitter that is urithin the confirmed wireless
reception range of the Weather Station for accuracy. lnstall one mounting screw (not inciuded) into a waii
Ieaving approximalely %of an inch (12.7mm) extended. Place the hanging hole (on the back of the
transmrtter) onto the rncunting scier.i and gently slide the transmitter Cown to secure it.
IMPORTANT: For true temperature and humidity readings, mount the transmitter out of direct sunlight on
a North-facing wall or in any other well shaded area like under an eave or deck rail. The maximum
transmitting range in open air is over 200-feet (60 meters). Obstacles such as walls, windows, stucco,
concrete, anC large metal objects can reduce the range. Place the transmitter at least 6 feet off the
ground to improve signai transmission.
srr Q aLnnH,r
ri
tulAX i I nrnr
Mr\ O DEu/ n. 8:.;
U* U;l9tp,
BUTTON FUNCTIONS:
Fig. B
Press and Release Functions Hold 3-5 seconds
SET l\,4ove through program rnenu.
Confrrm setting. Enter program menu set time, date, etc.
View Alarm.
Activate/Deactivate Alarm Alarm Set.
1 step forward (set-up)
Select temperature in 'C/"F.
1 step backwarcj (set-up). Fast backward (set-up).
i\4lN/r\tAX 1{ime LlAX values.
2limes [4lN values. Resets all [,41N / MAX values.
HEAT/DEW 1{ime Heat lndex.
2-times Dew Poini.
Switch channels outdoor
(multiple transmitters). Search for remote transmitter.
LIGHT
HOI.D ON/OFF Dim backlight for night time Dim backlight for night time.
Turn continuous backlight ON or OFF (a/c adapter).
LIGHT/SNOOZE Activates backlight when using only batteries
Trigger snooze alarm.
]3ollocaqllcoloso]uoilnql"/Co/-Jo+aLl]aseolalpuessold qsel]lll/Ylselnululaql:S3lnNIy{
'uJou ]xou aql ol eAoL! pue urJuuoc o] uounq f3s oql ssa,c
'.rnoll ]colloc aql ]colas ol uollnq t"l?"1- )o + aLl] asealal pue ssajd qse[ lllM Jnot] otll :UnOH
'r.Lrolr lxou oLil o] e^our pue u.rJuuoc ol ucunq j_ls 3-:
ssard HrZ lsalas o] uo]]nq l"/Co/- io + aLll asealor pue ssard L{seU lllM HZL :f WII UnOH ?Z/Zl
'enleA eql aDueqc 11rrvr uollnq lc/Cot ro + oql nueu Llei6ord eqt qbnotql a^oLrr llt/vt uopnq -=S 3--
:nNfir t/{vu90Hd
PROGMM MENU:
The SET button will move through the program menu. The + or J"C/"F button will change the value.
, 12124 HOUR TIME: 12H wili flash. Press and release the + or J'CI"F button to select 24H. Press
the SET button to confirm and move to the next item.
. HOUR: The hour will flash. Press and release the + or J"C/"F button to select the correct hour.
Press the SET button to confirm and move to the next item.
. MINUTES: The minutes will flash. Press and release the + or 1'Cl'F button to select the correct
minutes. Press the SET button to confirrn and move to the next item.
. YEAR: The year will flash. Press and release the + or -/"C/"F button to seiect the correct year.
Press the SET buiton to confirm and move to the next item.
. MONTH: The month will flash. Press and release the + or -l'Cl'F button to select the correct
month. Press the SET button to confirm and move to the next item.
. DATE: The date will flash. Press and release the + or J"C/"F button to select the correct date.
Press the SET button to confirm and exit the program menu.
Note: The Day of the Week will set automatically when the year, month and date are set.
FAHRENHEIT/CELSIUS: Press and release the -/"C/"F button once on the Wireless Weather Station
to switch from Fahrenheit to Celsius.
AUTO (channel scroll) - AUTO will appear in the outdoor temperature/humidity area when multiple
transmitters are received and the Wireless Weather Station is set to scroll through the channels
automatically.
. Press and release the CH button repeatedly untii the word AUTO shows. The Wireless Weather Station
will rotate through all available channeis.
. Press and release the CH button once to shov,r only one channe! continually.
The \ /ireless Weather Station can receive up to 3 outdocr transmitters. Use to monitor remote temperature
and humidity of up to 3 locations within a 200 Ft wireless range of the wireless reception is best.
Note: When only one transmitter is connected, you cannot see other channels.
BACKLIGHT:
,A/C adapter: The backlight is on continuously when operating the Weather Station
r.rith the S-volt a/c adapter.
. HIGH: The backlight is defaulted io Hl when the Aoapter is in use.
. L0: Press and release the LIGHT Hl/LO button to dim the backllght. Pi'ess and release again to return
to full strength.
. Note: When the Adapter is NOT in use, the l-ligh/Lo light feature is not available.
. OFF: Press and hold the HOLD ON/OFF button for 5 seconds, until the station beeps,
to turn the backlight off, to sleep,
. ON: Pr"ess and hold the llOLD ON/OFF button again until the station beeps, to iu!'n the backlight on.
. Note: When the backlight is off, press any button to activate the backlight for B seconds.
Battery power: Press and release the SNOOZE/LIGHT buttcn and the backlight will show for B seconds.
when operating on batteries only.
ALARM
When the alarm sounds, it continues for 2 minutes and then shuts off completely.
ALARM SET:
. ALARM HOUR: Press and hold ALARM button to enter alarm time setting mode. The Alarm Hour
will flash. Use the + or J"C/'F button to set the Hour. Press and release the ALARM button.
. ALARM MINUTE: The Alarm Minutes will flash. Use the + or J'CI"F button to set the Minutes.
Press and release the ALARM button to exit.
ALARM ACTIVATION:
. Press and release the ALARM button once to show Alarm Time.
. Press and release the ALARM button repeatedly to activate or deactivate the Alarm.
SNOOZE:
. When the alarm sounds, press the SNOOZE button to trigger snooze alarm for '10 minutes. The snooze
icon Zz will flash when the snooze feature rs active.
. To stop alarm for one day, press ALARM button, while in snooze mode.
USB CHARGE PORT:
The integrated USB charging port (on side) will charge devices when the Wireless
Weather Station is pluggeci into a power outlet. Note: This is a power outpui
(charging) port oniy. This port wril not supply power to the Wireiess Weather Station.
. Connect your existing USB charging corcj for your external device to the USB
chai'ging port on the side of the lVireless Weather Station to begin to charge.
Chai.ging times will vary. Note: Check that your device will charge with the USB
cord it came with.
IUIN/MAX TEMPERATURE/HUMIDITY DATA:
The Wireless Weather Station shows daily minimum and maximum temperatures each day starting at
midnight (12:00 AM). The station automatically resets the min/max temperatures at midnight (12:00 AM).
. View MM data: Press and release the MIN/MAX button once to view maximum temperature and
humidity values for indoor and outdoor data.
. View MIN data: Press and release the MIN/MAX button twice to view minimum temperature and humidity
values for indoor and outdoor data.
. Reset MIN/MAX data: Hold the MIN/MAX button for 5 seconds to reset all min/max values.
HEAT INDEX: Heat lndex combines the effects of heat (temperature) and humidity to determine how hot
it feels to a human being. Note: Heat index will be the same number as the temperature until the
temperature is above 80 degrees'F (26.7'C).
View Heat lndex: Press the HEAT/DEW button once and Heat lndex will show instead of the ambient
temperature.
DEW POINT: Dew point is the saturation point of the air, or the temperature to which the air has to be
cooled in order to create condensation. Note: Dew Point generally is lower than the temperature reading.
View Dew Point: Press ile HEAT/DEW button twice and Dew Point will show instead of the ambient
temperature.
a
-"-ESIrE,FTTERT-
. When this icon a appears in the indoor (lN) reading section, replace the batteries in the Wireless
Weather Station.
. When this icon A appears in the outdoor (OUT) readings section, replace the batteries in
the outdoor transmitter.
WEATHER FORECAST ICONS:
The Wireless Weather Station predicts weather conditions for the next 12-hours based on the change of
atmospheric pressure with 70-75% accuracy. Note: As weather conditions cannot be 100% correctly
forecasted we are not responsible for any loss caused by an incorrect forecast.
SUNNY PARTLYCLOUDY CLOUDY RAIN STORMY
ffiffiffiffiHffi
The Wireless Weather Station samples the barometric pressure every twelve minutes. These samples are
averaged hourly and daily then stored in nonvolatile memory. The three hour pressure icon change is
based ofi of the last four average hourly readings.
As the Wireless Weather Station builds memory, it will compare the current average pressure to the past
forty day average pressure for increased accuracy. The longer the station operates in one location the
more accurate the forecast icons will be.
CARE AND MAINTENANCE:
. Do Not Mix Old and New Batteries.
. Do Noi Mix Alkaline, Standard, Lithium or Rechargeable Batteries.
. Do not expose the Wireless Weather Station to extreme temperatures, vibration or shock.
. Keep Wireless Weather Station dry.
. Clean Wireless Weather Station with a soft damp cloth. Do not use solvents or scouring agents.
. The Wireless Weather Station is not a toy. Keep it out of reach of children.
. The Wireless Weather Station is not to be used for medical purpose or for public information, but is
designed for home use only.
. The specifications of this product may change without prior notice.
. lmproper use or unauthorized opening of housing will void the warranty.
. lf the unit does not work properly, change the batteries and/or check the a/c cord connection.
SPEGIFICATIONS:
lndoor: I Tffipe€trre Rar8e: +32"F to +122'F (0'C to sO"C)
Humidity Range: .1 t%-99% (RH)
lnterval: Aboutevery30econds
Outdoor:
Range: Temperature, dew point, heat index 40'F IoTzto'F(4fC to 60'C)
Alkaline Batteries: -20"F to 140"F G28.8"C to 60"C)
Lithium Batteries: -40"F to 140'F (40'C to 6O"C)
Temperatures below -20"F (-28.8"C)
require Lithium batteries in the outdoor transmitter
Humidity Range: 1%-9970 (RH)
Distane: Over 200 ft. (60 meters) RF 433MHz (open air)
lnterual: About every 50 semnds
Power:
Wireless Weather Station: s-volt a/c power adapter (included)
Optional 3-AAA 1.5V, lEC, LR6 batteries (not included)
Transmitter: 2-AAA 1.5V, IEC, LR6 batteries (not included)
Battery Life:
Transmitter: Battery Life: Battery life is over 24 months when using reputable
battery brands for both Alkaline and Lilhium batteries
Wireless Weather Station: Battery Backup: Battery life is over 24 months when using the AC
adapter for pdmary power
USB: Output: 'l Amp maximum curenl
FCC Disclaimer:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may €use undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER
AUTHORIry TO OPEMTE THE EQUIPMENT.
Jlrgear @
14023 Catalina Street, San Leandro, CA 94577
@2014 JLR Gear- Made in China
Any questions, please €ll Customer Seryice at 1t00-29-0'111; 8:30 a.m. - 5 p.m., PST, Monday-Friday or email us at [email protected]
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Cutdoof temperature
ices not sl]olv
afler 3 minutes.
Setup was not
correctly compieted Remove the a/c power adapter and all batteries
fror both ua,ts and s:art the setuD process again.
OLrtdoor temperature
does not show after
second attempt.
Wireless Weather Station not
receiving wireless signal. Sl de open the battery cover of the outdoor transmitter
to revea the TX button. Push down on the TX button
for 3 seconds to send a w:reless signal to the lvireless
Weather Station. On the Vy'lreless Weather Slalion, hold
the CH button for 3-5 seconds to search for
the transmitter.
FC
Table of contents
