Johnson Controls Unitary Products YH-10 Quick start guide

R-410A
SPLIT-SYSTEM
AIR-COOLED CONDENSING UNITS
AND AIR HANDLERS
YH-07 thru -25 and YJ-10 thru -20
CONDENSING UNIT MODELS
PH-07 thru -15 and PJ-15 thru -20
HEAT PUMP UNIT MODELS
NH-07 thru -25 and NJ-10 thru -20
AIR HANDLING UNIT MODELS
7.5 - 25 Ton
60 Hertz
TECHNICAL
GUIDE
TECHNICAL
GUIDE
505430-BTG-P-0316
ISO 9001
Certified Quality
Management System
YH/YJ/PH Outdoor Units
YH/YJ/PH/PJ Outdoor Units
NH/NJ Indoor Units
(Except YH-25)
Description
UP condensing units and heat pumps are completely assembled,
piped and wired at the factory to provide a single-piece unit for
shipment and rigging. Each unit is pressurized with a holding charge of
refrigerant R-410A for storage and/or shipping.
The compact design, clean styling, small footprint, and quiet operation
make these condensing units and heat pumps suitable for almost any
outdoor location. On rooftops... because they weigh much less than a
single package unit of similar capacity and are much easier to rig and
support. On the ground... because the footprint is compact allowing a
variety of applications.
Both the UP condensing units and heat pumps are equipped with
reliable Simplicity® SE microprocessor controls to assure proper
operation and unit protection for long product life. Products from 10 to
20 tons are available in single or dual (2 or 4 pipe) refrigerant circuits
for redundancy in operation and various application choices such as
one outdoor unit matched with two indoor units.
The UP air handling units are completely assembled units, including a
well-insulated cabinet, a DX cooling coil with copper tubing, aluminum
fins, expansion valve(s), distributor(s), 2” throwaway filters, a
centrifugal blower, a blower motor, an adjustable belt drive, a blower
motor contactor and a small
holding charge of nitrogen.

505430-BTG-P-0316
2Johnson Controls Unitary Products
Units are shipped in the vertical position ready for field
installation, but can be easily converted to horizontal position.
An added benefit of the UP air handling units is they are
designed to operate with either a condensing unit or a heat
pump and no field modification or special unit is required for
heat pump applications.

505430-BTG-P-0316
Johnson Controls Unitary Products 3
Table of Contents
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Condensing Unit Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Outdoor Unit Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Air Handling Unit Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Guide Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Physical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Unit Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cooling and Heating Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Capacity Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Air Handling and Hot Water Coil Accessory Heating Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Air Handling and Steam Coil Accessory Heating Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Airflow Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Sound Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Electrical Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Typical Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Weights And Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

505430-BTG-P-0316
4Johnson Controls Unitary Products
Nomenclature
Product Category
Y = Split System, Condenser, AC, R-410A
Product Identifier
H = Standard Efficiency, 2-Pipe, R-410A
J = Standard Efficiency, 4-Pipe, R-410A
Nominal Cooling Capacity - MBH
-07 = 7.5 Ton
-10 = 10 Ton
-12 = 12.5 Ton
-15 = 15 Ton
-20 = 20 Ton
-25 = 25 Ton
C00 = Cooling Only
Product Options
T = 208/230-3-60
W = 460-3-60
X = 575-3-60
Configured Split Condenser Model Number Nomenclature
A = Standard Motor
Airflow
Product Generation
5 = Fifth Generation
Voltage
Heat Type & Nominal Heat Capacity
YH-20 C00 A TAAA 5A
Product Style
A = Style A
P = Split System, Condenser, HP, R-410A
AA = None
AB = Phase Monitor
AC = Coil Guard
AE = Phase Monitor + Coil Guard
EA = E-Coat Condenser Coil
EB = E-Coat Condenser Coil + Phase Monitor
EC = E-Coat Condenser Coil + Coil Guard
EE = E-Coat Condenser Coil + Coil Guard
+ Phase Monitor
LA = Low Ambient
LB = Low Ambient + Phase Monitor
LC = Low Ambient + Coil Guard
LD = Low Ambient + Phase Monitor
+ Coil Guard
LE = Low Ambient + Technicoat Cond. Coil
LF = Low Ambient + Technicoat Cond. Coil
+ Phase Monitor
LG = Low Ambient + Technicoat Cond. Coil
+ Coil Guard
LH = Low Ambient + Technicoat Cond. Coil
+ Phase Monitor + Coil Guard
LJ = Low Ambient + ElectroFin Cond. Coil
LK = Low Ambient + ElectroFin Cond. Coil
+ Phase Monitor
LL = Low Ambient + ElectroFin Cond. Coil
+ Coil Guard
LM = Low Ambient + ElectroFin Cond. Coil
+ Phase Monitor + Coil Guard
TA = Technicoat Condenser Coil
TB = Technicoat Condenser Coil + Phase
Monitor
TC = Technicoat Condenser Coil + Coil Guard
TE = Technicoat Condenser Coil + Coil Guard
+ Phase Monitor
Installation Options
A = None
B = Option 1
C = Option 2
D = Options 1 & 2
E = Option 3
F = Option 4
G = Options 1 & 3
H = Options 2 & 3
J = Options 1, 2 & 3
K = Options 1 & 4
L = Options 2 & 4
M = Options 1, 2 &4
P = Options 3 & 5
Q = Options 1, 3 & 5
R = Options 4 & 5
S = Option 5
T = Options 1 & 5
V = Options 1, 4 & 5
1 = Disconnect
2 = Non Pwr’d Conv Outlet
3 = BACnet MS/TP on Simplicity SE
4 = Fault Detection Device
5 = Pwr’d Conv Outlet
Options
Product Category
N = Split System, Air Handler, AC & HP, R-410A
Product Identifier
H = Standard Efficiency, 2-Pipe, R-410A
J = Standard Efficiency, 4-Pipe, R-410A
Nominal Cooling Capacity - MBH
-07 = 7.5 Ton
-10 = 10 Ton
-15 = 15 Ton
-20 = 20 Ton
-25 = 25 Ton
C00 = Cooling Only
Product Options
Installation Options
A = None
T = 208/230-3-602
W= 460-3-602
S = 208/230/460-3-60
X = 575-3-60
Configured Split Air Handler Model Number Nomenclature
B = 1.5 HP Motor
C = 2.0 HP Motor
D = 3 HP Motor
E = 5 HP Motor
F = 7.5 HP Motor
N = None (Motor Drive Kit Req)1
Airflow
Product Generation
1 = First Generation
2 = Second Generation
3 = Third Generation
Voltage
Heat Type & Nominal Heat Capacity
NH-20 C00 B SAAA 3A
Product Style
A = Style A
1. Motors are not shipped with
25 ton Air Handler Units.
AA = No Options Installed
EJ = E-Coat Evaporator Coil
TJ = Technicoat Evaporator Coil
2. NH/NJ-20 Airflow Option
“F” Only.

505430-BTG-P-0316
Johnson Controls Unitary Products 5
Condensing Unit Features and Benefits
Features
• Meets or exceeds ASHRAE 90.1 standards.
• Scroll compressors provide both high efficiency and
reliability.
•Simplicity®SE Controls
• Dual refrigerant circuits on PH and YJ models.
• Condensing unit coils are constructed of reliable and
durable Micro-Channel aluminum tube and fins for long
lasting, efficient operation. Mirco-Channel technology
provides exceptional durability along with reduced
product weight and less refrigerant charge. Heat pumps
units are equipped with aluminum fin, copper tube coils
providing durability, reliability and value.
• Multiple condensing unit and air handler match-ups
provide a wide range of application choices from
oversized indoor motors to dual indoor units matched-
up with single outdoor units.
• Crankcase heaters that de-energize when compressors
are operating.
• Both high and low pressure controls. Since these
controls are self-contained, there are no capillary lines
to be damaged.
• Internal compressor motor protection.
• Class 2, 24-volt thermostat control circuit protected by a
re-settable breaker.
• Standard factory installed service valves.
• Filter-driers are shipped in the unit's control box for field
installation in the liquid line leaving the outdoor unit.
• Copper stub-outs are factory mounted on the suction
and liquid lines to simplify the field piping connections.
•Simplicity® SE Controls provide stable cooling
operation at ambient temperatures down to 40°F with
low ambient kits available for operation to 0°F.
• Capacity staging for more economical operation and
stable temperature levels within the conditioned space.
•Simplicity® SE Controls control board uses a three
times, you're out philosophy. The high, low-pressure
switch, anti-freeze protection, low voltage or heating
high limit must trip three times within two hours before
the unit control board will lock out the associated
compressor. An alarm message will be displayed on the
LCD screen.
•Simplicity® SE Controls monitor each safety
independently (High pressure, low pressure, low
voltage) allowing ease of troubleshooting if any
problems arise.
• Inherently protected condenser fan motors.
• Technicoat or E-Coat coated outdoor coils for sea coast
or corrosive environment applications.
• Factory installed disconnect to allow power to be
removed from the unit when performing periodic
maintenance or for service.
• Factory installed powered or non-powered 115 volt GFI
outlet.
• Factory installed phase monitor to protect the unit from
phase loss or phase reversal.
Benefits
The UP® condensing units and heat pumps can be applied
on a rooftop or at ground level... due to their ample sub-
cooling capacity which allows them to be located three or
more stories below the evaporator coil.
After assembly, the unit is pressurized with a combination of
Refrigerant R-410A and nitrogen for pressure testing and
additional leak testing. During this pressure test, the
operation of the high pressure control is checked. As the unit
is being evacuated and dehydrated, the operation of the low
pressure control is also checked.
Every compressor, condenser fan motor, crankcase heater,
and electrical control circuit is checked to assure a trouble-
free start-up and years of reliable operation. The condenser
fan guards are vinyl-coated to provide additional rust
protection and to enhance the appearance of the unit.
Compressors are mounted on rubber isolators to reduce the
transmission of vibration. Vertical discharge condenser fans
direct sound upward and away from any surrounding
structures.
All sheet metal parts are constructed of commercial grade
galvanized steel. After fabrication, each part is thoroughly
cleaned to remove any grease or dirt from its surfaces. The
external parts are coated with a powder paint to assure a
quality finish for many years. This UL approved coating
system has passed the 1000 hour, 20% salt spray test per
ASTM Standard B117.
All condensing unit and heat pump models include a 5-year
limited warranty on the compressor(s) and 1-year limited
warranty on all other parts. The matching line of air handling
units carries a 1-year limited parts warranty.
Outdoor Unit Accessories
Coil Guards: Wireform coil guards for added protection of
outdoor coils. Designed to mount on each side of the product
if required to provide protection from minor impacts or large
debris.
Hail Guards: Hood type hail guards designed to protect the
outdoor coils from hail. Can be installed on a single side or
both to provide protection from storms that may produce hail.
Low Ambient Kits: Kits designed to allow the cooling only
units to operate between 0°F and 40°F in the cooling mode.
Standard cooling is allowed to 40°F. (Not designed for
operation on heat pump units).
Air Handling Unit Features and Benefits
Features
These air handlers can be arranged for a variety of air
discharge patterns in either the horizontal or vertical position.
Refer to the unit installation instructions for other application
possibilities.

505430-BTG-P-0316
6Johnson Controls Unitary Products
Benefits
Air handling units are designed with two distinct modules to
provide maximum application flexibility. All are shipped as
single packages with the blower module mounted on top of
the coil module. The blower module can be repositioned in
the field to meet a large number of vertical and horizontal
applications.
The 7.5 thru 20 Ton blower module includes the blower
wheels along with factory-mounted motor and drive. The 25
Ton blower module includes the blower wheels with field
mounted motor and drives. All models offer two motor
horsepower options to meet both standard and high static
airflow requirements.
The coil module includes direct expansion coils, 2 in.
throwaway filters with the option to accept 4” filters, liquid line
solenoid valves for capacity reduction, thermal expansion
valves, distributors and a non-corrosive, composite
condensate drain pan.
Every air handling coil is pressurized with air and leak tested
under water. After the headers are brazed onto the coil and
the coil is installed in the unit, the coil is pressurized with
nitrogen for pressure testing and additional leak testing. After
the coil is evacuated and dehydrated, it is pressurized with a
holding charge of nitrogen for storage and/or shipping.
These air handlers, combined with condensing units, provide
years of quiet, efficient and dependable operation. These
units are manufactured under ISO 9001 Quality System
Certification.
Unit Installation
Units may be bottom-supported or ceiling-suspended and
can be arranged to meet almost any space or duct
requirements. Each unit is available with a choice of blower
motors horsepower and other accessories to make them
suitable for most applications.
Air Handling units are available in either two or four pipe
configurations from 7.5 to 25 tons. The dual and single circuit
options provide a wide variety of application and unit match-
up possibilities.
Blower Motors: Different HP motors are available for each
unit to meet almost any air delivery requirement. All motors
are UL approved, have permanently lubricated ball bearings
and are mounted within the insulated cabinet of the units to
minimize the transmission of sound to the surrounding space.
1.5-5 HP motors are inherently protected. 7.5 HP motors
require motor overload protection.
Overload Relay (7.5HP): These blower motors do not have
inherent protection and require external motor overload
protection. NH/NJ-20 "F" models Overload Relays are factory
installed. NH-25 models Overload Relays are field installed.
Power wiring for blower motor is supplied in the Overload
Relay Kit. See details in Overload Relay Kit and Overload
Relay Setting Tables on Page 70.
Factory-Mounted Components
Part Load Operation: These air handlers with DX (Direct
Expansion) coils rated at 10 tons of capacity and above have
multiple coils with pre-piped distributors, expansion valves
and solenoid valves. Field modifications are not required for
part load operations. Capacity reduction not only provides
economical operation, but also maintains stable temperature
and humidity levels in the conditioned space.
BAS Control: Simplicity® SE with Communication Option
Control - The York® Simplicity® SE with Communication
Option Control is factory installed. It includes all the features
of the Simplicity® SE control with an additional gateway to
BACnet MS/TP (programmable to Modbus or N2 protocols).
Easy Service: Serviceable expansion valves are provided on
every unit. These valves are factory-installed to provide many
years of trouble-free operation. If service is required, it is not
necessary to unbraze any joints. The expansion valves also
include a tee fitting to allow easy installation of hot gas
bypass if required.
Coil Protection: The indoor coils of these air handlers can
have factory applied Technicoat or Electrofin coating to
provide extended life to the indoor coil in standard
applications and additional corrosion protection on those
applications in sea coast or corrosive environments.
Accessories
Base Sections: Base sections can be used to elevate units
above the floor. If desired, a moderate percentage of outdoor
air may be introduced through these sections by cutting an
access opening to accommodate the outdoor air duct
connection. These bases include a durable finish to match
the evaporator blower unit. The base may have to be
insulated for certain applications.
Hot Water Coils: Drainable water coils are available for field
installation between the blower and the coil modules of both
horizontal and vertical units. Since their casings match the
dimensions and the finish of the basic units, they become an
integral part of the unit after installation. The coils slide out of
their casings for easy installation. Hot water coils have
copper tubes that have been mechanically expanded into
aluminum fins. Both headers are located on the same end of
the coil. Coils are leak-tested at 325 psig under water and
dried before their connections are capped for storage and
shipping.
Steam Coils: Steam coils are available for installation
between the blower and coil modules of both horizontal and
vertical units. Since the casing matches the dimensions and
the finish of the basic unit, it becomes an integral part of the
unit after installation. The coil slides out of the casings for
easy installation and is pitched in the casings to facilitate
condensate drainage. The coil has copper tubes that have
been mechanically expanded into aluminum fins. Both
headers are located on the same end of the coil. The coil is
leak-tested at 325 psig and dried before the connections are
capped for storage and shipping.

505430-BTG-P-0316
Johnson Controls Unitary Products 7
Bottom Return: Air handling unit can be quickly converted to
bottom return for both vertical and horizontal applications. All
that is required is the removal of several screws and a single
panel on 7.5-15 ton and two panels on the 20 ton AHU.
Optional painted panel can be ordered to cover the side
return opening when utilizing the bottom return.
Supply Air Plenums: These fully insulated plenums are
available for free standing units located within the conditioned
space. They are shipped fully assembled for easy field
installation, are finished to match the exterior of the basic
unit, and include double deflection grills that can be adjusted
to vary the throw, spread and drop of the supply air.
Guide Specifications
Split System Cooling Only Condensing Units
Models: YH-07 thru -25, YJ-10 thru -20 & Split
System Heat Pump Models: PH-07 thru -20, PJ-15
thru -20
General
• Factory assembled, single piece, air cooled condensing
unit designed for outdoor installation.
• Factory wired, piped, and tested for leakage and
functionality to assure trouble-free installation and start-
up.
• Rated in accordance with AHRI Standard 340/360.
• Manufactured in a facility registered under the ISO 9002
manufacturing quality standard.
• Designed and tested in accordance with ASHRAE 15
Safety Code for Mechanical Refrigeration and comply
with NEC.
• Cooling performance rated in accordance with DOE
and AHRI test procedures.
• CSA listed and classified to UL 1995/CAN/CSA No.
236- M90 standards.
• One year limited parts warranty on complete unit with
an additional four year compressor warranty.
Unit Operating Characteristics
Operating Range shall be between 125° F to 40° F in cooling
as standard from factory.
• The capacity of the condensing unit shall meet or
exceed _____ Btuh at a suction temperature of _____
F. The power consumption at full load shall not exceed
_____ kW.
• The combination of the condensing unit and the
evaporator or fan coil unit shall have a total net cooling
capacity of _____ Btuh or greater at conditions of
_____ cfm entering-air temperature at the evaporator at
_____ F wet bulb and _____ F dry bulb, and air
entering the condensing unit at _____F.
• The system shall have an EER of _____ Btuh/ Watt or
greater at standard AHRI conditions.
Installer Shall
• Furnish UP™ air-cooled condensing units, heat pump
or equivalent in accordance with the performance
schedule shown on the plans, and
• Unit shall be stored and handled in accordance with unit
manufacturer's instructions.
• Install each unit as shown on the plans in accordance
with the manufacturer’s recommendations and all
applicable national and local codes
Unit Construction
• Constructed of zinc-coated, galvanized steel.
• Exterior surfaces bonded and coated with baked
enamel finish by a powder paint process capable of
withstanding a minimum of 1000 salt spray hours
according to ASTM B117.
• Cabinet screws that comply with ASTM B117 salt spray
test for a minimum of 750 hours.
• Permanently attached heavy-gage perimeter base rails
with forklift slots and lifting holes.
• Removable access panels to all internal components.
• Separate access panel to controls.
• Access panels to allow outdoor coil cleaning.
Compressor(s)
• Hermetic scroll type, internally protected with high-
pressure relief and over temperature protection.
• Two stage units operate in 50% capacity increments.
• Suction gas cooled
• Voltage range of ±10% of unit nameplate voltage.
• Neoprene isolators minimize sound transmission and
vibration.
• Belly-band crankcase heaters keep refrigerant from
diluting sump oil.
• Full charge of compressor oil
Outdoor Condenser Unit Coils
• Draw thru configuration
• Constructed with Micro-channel aluminum fins and
aluminum tubing. All refrigerant tubing must share a
common header.
Heat Pump Unit Outdoor Unit Coils
• Draw thru configuration
• Constructed with aluminum plate fins mechanically
bonded to seamless internally enhanced copper tubes
with all joints brazed.

505430-BTG-P-0316
8Johnson Controls Unitary Products
Condenser Fans
• Direct driven propeller-type fans
• Statically and dynamically balanced
• Aluminum blades riveted to corrosion resistant steel
spider brackets.
• Arranged for vertical air discharge.
• Equipped with PVC coated steel wire safety guards.

505430-BTG-P-0316
Johnson Controls Unitary Products 9
Condenser Motors
• Totally enclosed, air over cooled.
• Inherent overload protection.
• Permanently lubricated bearings.
• Must cycle to allow cooling operation down to 40°F.
Refrigerant Piping
• Solid core filter-drier(s) ship loose for field installation.
• Liquid and suction line service valves with gauge ports.
• Suction and discharge line service ports accessible
from unit. Ports capped for leak prevention.
• Liquid line magnetic check valves
• Holding charge of R410A refrigerant.
Electrical Requirements
• Single-point connection electrical power.
• Nominal unit electrical characteristics shall be _____ v,
3-ph, 60 Hz. The unit shall be capable of satisfactory
operation within voltage limits of ____ v to _____ v.
• Condenser fan motors and secondary of transformers
shall be grounded.
Unit Controls
• All 24-volt control circuit, powered by a 24 volt
transformer(s) and protected by a resettable breaker.
• Conventional thermostat must provide operation for
both condensing units and heat pumps without an “O”
output from the thermostat.
• Low voltage terminal strip for simple hook-up.
• Compressor motor protection shuts down unit for motor
over-current, over-temperature or low voltage
conditions.
• Safety lockouts provide reset capability at the space
thermostat or base unit should any of the following
standard safety devices trip and shut off compressor:
a. Loss-of-charge/Low-pressure switch.
b. High-pressure switch.
c. Control board diagnostics and fault message display.
d. Safety lockouts send a 24 volt signal to the control
board's "X" terminal, allowing notification to the user
via the thermostat fault light (if present).
e. In the unlikely event any faults should occur, the unit
control board will store the faults in its internal
memory. The LCD display will scroll the 5 MOST
critical faults, however, all fault messages can be
extracted via USB device, displayed real-time via the
MAP Gateway as well as be broad-casted through a
BAS system (if applicable). The UCB will provide fault
messages in plain English to ensure the user can
easily understand the specific fault.
Non-fused Disconnect Switch
• Factory-installed, internally mounted.
• Accessible from outside the unit.
• NEC and UL approved non-fused switch.
• Provides power off lockout capability.
Convenience Outlet
• Factory-installed, internally mounted.
• Accessible from outside the unit.
• 115V, 15 amp GFI receptacle with independent fuse
protection.
• Required voltage provided by factory-installed step-
down transformer or field supplied 115v circuit.
Low-ambient Head Pressure Control
• Standard operation down to 40 °F without a low
ambient kit.
• Operation down to 0°F with a field-installed low ambient
kit accessory. The controller modulates the fan motor
speed in response to liquid line temperature or
pressure.
Coil Guard
Factory or field installed decorative grille shall be placed on
the units to protect condenser coil after installation.
Hail Guard Package
Field installed hail guard package shall protect coils against
damage from hail and other flying debris.
Coated Condenser Coils
Special phenolic or epoxy polymer coating available as a
factory option on both outdoor and indoor coils.
Each Unit Shall Be:
• Covered by a 1-year limited parts warranty on the
complete unit and 5-year on compressor(s).
• In current production with published literature available
to check performance, limitations, specifications, power
requirements, dimensions, operation and appearance.
• Indoor unit shall be equipped with a V-belt drive option
that will permit the blower RPM to be adjusted to meet
the CFM requirements of the air delivery system. (Refer
to Technical Guide for Airflow Capabilities.)

505430-BTG-P-0316
10 Johnson Controls Unitary Products
Each Unit Enclosure Shall Have:
• Exterior panels of 18 gauge steel, finished with baked
enamel to provide a long lasting quality appearance
• Removable panels to provide easy access to the
internal components for maintenance and service on
condensing units, heat pumps and air handlers
• Air handling units must have a filter rack that accepts
both 2” and 4” filters.
• The dimensions of each unit shall not exceed those
specified in the manufacture’s literature.
• The minimum application clearances for condensing
units, heat pumps and air handlers must meet those
specified in the manufacturer’s literature.
The Blower Motor Shall:
• Be mounted within the insulated cabinet to minimize the
transmission of sound to the surrounding space, and
any motor 7.5 HP or greater must have a service factor
of 1.15.
The Evaporator Coil Shall:
• Consist of copper tubes arranged in staggered rows,
mechanically expanded into aluminum fins,
• Be draw-through, and
• Include factory-mounted distributors, expansion valves
and solenoid valves for capacity reduction.
The Blower Wheels Shall:
Be dynamically balanced to minimize the levels of sound and
vibration generated by the unit.

505430-BTG-P-0316
Johnson Controls Unitary Products 11
Physical Data
YH-07 thru -25 and YJ-10 thru -20 Physical Data
Component Models
YH-07 YH-10 YJ-10 YH-12 YJ-12 YH-15 YJ-15 YH-20 YJ-20 YH-25
NominalTonnage 7.5101012.512.51515202025
REFRIGERANT
Refrigerant type R-410A R-410A R-410A R-410A R-410A R-410A R-410A R-410A R-410A R-410A
Holding charge (lb)1(each system)
1Holding Charge is the amount in the unit as shipped from the factory.
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
Operating Charge (lb)2
2Includes matched indoor blower unit with 25 ft of piping.
System #1 14.0 19.25 9.9 24.0 11.5 27.0 13.5 33.5 18.8 35
System #2 --- --- 9.9 --- 11.5 --- 13.5 --- 18.8 ---
DIMENSIONS (inches)
Length 59.1 59.1 59.1 59.1 59.1 59.1 59.1 59.1 59.1 59.1
Width 31.9 31.9 31.9 31.9 31.9 64.1 64.1 64.1 64.1 64.1
Height 44.5 50.0 50.0 50.0 50.0 44.5 44.5 50.0 50.0 50.0
WEIGHTS (lb)
Shipping 390 499 493 499 493 914 899 945 930 945
Operating 387 497 490 497 490 909 894 942 927 942
COMPRESSORS3
3All compressors include crankcase heaters.
Type Single Scroll Tandem Scroll Single Scroll Tandem Scroll Single Scroll Tandem Scroll Single Scroll Tandem Scroll Single Scroll Tandem Scroll
Quantity 1121212121
Nominal Capacity (Tons) System #1 7.5 10 5 12.5 6.3 15 7.5 20 10 25
System #2 --- --- 5 --- 6.3 --- 7.5 --- 10 ---
Capacity Stages System#11212121212
System #2 --- --- 1 --- 1 --- 1 --- 1 ---
SYSTEM DATA
No.RefrigerationCircuits 1121212121
Suction Line OD (in.) 1 1/8 1 3/8 1 1/8 1 3/8 1 1/8 1 5/8 1 1/8 1 5/8 1 3/8 2 1/8
Liquid Line OD (in.) 5/8 7/8 5/8 7/8 5/8 7/8 5/8 7/8 5/8 7/8
OUTDOOR COIL DATA
Face area (Sq. Ft.) 23.8 29.0 29.0 29.0 29.0 47.5 47.5 58.1 58.1 58.1
Rows 1111111111
Fins per inch 23 23 23 23 23 23 23 23 23 23
Tube diameter (in./MM) 0.71 / 18 0.71 / 18 0.71 / 18 0.71 / 18 0.71 / 18 0.71 / 18 0.71 / 18 0.71 / 18 0.71 / 18 0.71 / 18
Circuitry Type 2-pass 2-pass 2-pass 2-pass 2-pass 2-pass 2-pass 2-pass 2-pass 2-pass
Refrigerant Control --- --- --- --- --- --- --- --- --- ---
CONDENSER FAN DATA
No. Fans / Diameter (in.) 2/24 2/24 2/24 2/24 2/24 4/24 4/24 4/24 4/24 4/24
Type Axial Axial Axial Axial Axial Axial Axial Axial Axial Axial
Drive type Direct Direct Direct Direct Direct Direct Direct Direct Direct Direct
No. speeds 1111111111
Number of motors System#12222242424
System #2 --- --- --- --- --- --- 2 --- 2 ---
Motor HP (ea.) 1/3 3/4 3/4 3/4 3/4 1/3 1/3 3/4 3/4 3/4
Rotation4
4When viewing the shaft end of the motor.
CW CW CW CW CW CW CW CW CW CW
RPM 850 1100 1100 1100 1100 850 850 1100 1100 1100
Nominal CFM System #1 7500 9800 9800 9800 9800 15000 7500 19600 9800 19600
System #2 --- --- --- --- --- --- 7500 --- 9800 ---

505430-BTG-P-0316
12 Johnson Controls Unitary Products
PH-07 thru -20 and PJ-15 thru -20 Physical Data
Component Models
PH-07 PH-10 PH-15 PJ-15 PJ-20
Nominal Tonnage 7.5 10 15 15 20
REFRIGERANT
Refrigerant type R-410A R-410A R-410A R-410A R-410A
Holding charge (lb)11.0 1.0 1.0 1.0 1.0
Operating Charge (lb)2System #1 23.9 31.75 54.0 27.0 34.0
System #2 --- --- --- 27.0 34.0
DIMENSIONS (inches)
Length 59.1 59.1 59.1 59.1 59.1
Width 31.9 31.9 64.1 64.1 64.1
Height 44.5 50.0 44.5 44.5 50.0
WEIGHTS (lb)
Shipping 421 543 947 921 1090
Operating 430 574 968 942 1126
COMPRESSORS3
Type Single Scroll Tandem Scroll Tandem Scroll Single Scroll Single Scroll
Quantity 1 1 1 2 2
Cooling
Nominal Capacity (Tons) System #1 7.5 10 15 7.5 10
System #2 --- --- --- 7.5 10
Capacity Stages System#112211
System #2 --- --- --- 1 1
Heating
Nominal Capacity (Tons) System #1 & #2 7.5 10 15 15 20
Capacity Stages System #1 & #2 1 1 1 1 1
SYSTEM DATA
No. Refrigeration Circuits 1 1 1 2 2
Suction Line OD (in.) 1 1/8 1 3/8 1 5/8 1 3/8 1 3/8
Liquid Line OD (in.) 5/8 7/8 7/8 5/8 5/8
OUTDOOR COIL DATA
Face area (Sq. Ft.) 23.8 29.0 47.5 47.5 58.1
Rows 22222
Fins per inch 20 20 20 20 20
Tube diameter (in./MM) 0.38 / 10 0.38 / 10 0.38 / 10 0.38 / 10 0.38 / 10
Circuitry Type Interlaced Interlaced Interlaced Interlaced Interlaced
Refrigerant Control TXV TXV TXV TXV TXV
CONDENSER FAN DATA
No. Fans / Diameter (in.) 2/24 2/24 4/24 4/24 4/24
Type Axial Axial Axial Axial Axial
Drive type Direct Direct Direct Direct Direct
No. speeds 1 1 1 1 1
Number of motors System#122422
System #2 --- --- --- 2 2
Motor HP (ea.) 1/3 3/4 1/3 1/3 3/4
Rotation4CW CW CW CW CW
RPM 850 1100 850 850 1100
Nominal CFM System #1 7500 9800 15000 7500 9800
System #2 --- --- --- 7500 9800
1Holding Charge is the amount in the unit as shipped from the factory.
2Includes matched evaporator unit with 25 ft of piping.
3All compressors include crankcase heaters.
4When viewing the shaft end of the motor.

505430-BTG-P-0316
Johnson Controls Unitary Products 13
NH-07 thru -20 and NJ-10 thru -20 Indoor Unit Physical Data
Component Models
NH-07 NH-10 NJ-10 NH-15 NJ-15 NH-20 NJ-20
NominalTonnage 71/2101015152020
DIMENSIONS (inches)
Length 56.0 56.0 56.0 74.5 74.5 98.5 98.5
Width 30.0 30.0 30.0 33.0 33.0 30.0 30.0
Height 65.0 65.0 65.0 75.0 75.0 65.0 65.0
WEIGHTS (lb)
Unit Shipping 526 573 575 796 796 938 938
Unit Operating With
Standard Motor and Drive 498 539 541 764 764 873 873
High Static Motor and Drive 500 550 552 792 792 903 903
INDOOR BLOWER (Forward Curve)
Diameter x Width 12 x 12 15 x 15 15 x 15 18 x 18 18 x 18 15 x 15 15 x 15
Quantity 1111122
INDOOR COIL
Face area (Sq. Ft.) 10.6 10.6 10.6 18.3 18.3 20.0 20.0
Rows 3443444
Fins per inch 15 15 15 15 15 15 15
Tube diameter 3/8 3/8 3/8 3/8 3/8 3/8 3/8
Circuitry Type Interlaced Interlaced Interlaced Interlaced Interlaced Interlaced Interlaced
Refrigerant Control TXV TXV TXV TXV TXV TXV TXV
SYSTEM DATA
No.RefrigerationCircuits 1121212
Suction Line OD (in.) 1 1/8 1 3/8 1 1/8 1 5/8 1 3/8 1 5/8 1 3/8
Liquid Line OD (in.) 5/8 7/8 5/8 7/8 5/8 7/8 7/8
FILTERS
Size and Quantity Per
Model (In.) 16 x 25 x 2 4 4 4 --- --- 8 8 20 x 24 x 2 --- --- --- 6 6 --- ---
FACE AREA (SQ. FT.) 11.1 11.1 11.1 20.0 20.0 22.2 22.2
Size and Quantity Per
Model (In.) 16 x 25 x 4 4 4 4 --- --- 8 8 20 x 24 x 4 --- --- --- 6 6 --- ---
FACE AREA (SQ. FT.) 11.1 11.1 11.1 18.0 18.0 22.2 22.2

505430-BTG-P-0316
14 Johnson Controls Unitary Products
NH-25 Indoor Unit Physical Data
Component Models
NH-25
Nominal Tonnage 25
DIMENSIONS (inches)
Length 100.1
Width 38.1
Height 74.6
WEIGHTS1(lb)
1Motors, Drive and Overload Kits must be
ordered separately for the NH-25. The Motor
Drive and Overload Kits are to be field installed.
Unit Shipping 1067
Unit Operating With
5 hp Motor and Drive 1130
7.5 hp Motor and Drive 1157
INDOOR BLOWER (Forward Curve)
Diameter x Width 18 X 18
Quantity 2
INDOOR COIL
Face area (Sq. Ft.) 25.8
Rows 4
Fins per inch 16
Tube diameter 3/8
Circuitry Type Interlaced
Refrigerant Control TEV
SYSTEM DATA
No. Refrigeration Circuits 1
Suction Line OD (in.) 2 1/8
Liquid Line OD (in.) 7/8
FILTERS
Size and Quantity Per
Model (In.) 20 x 25 x 2 10
FACE AREA (SQ. FT.) 34.7
ACCESSORY
HOT WATER COIL DATA
Face area (Sq. Ft.) 21.2
Rows 2
Fins per inch 12
Tube diameter (Copper) OD (In.) 1/2
Connections (Supply and Return) OD (In.) 1 3/8
Weight (lb) 150
SYSTEM COIL DATA
Face area (Sq. Ft.) 18.2
Rows 1
Fins per inch 8
Tube diameter (Copper) (In.) 1
Connection, (NPTE) (In.)
Inlet 2
Outlet 1-1/2
Weight (lb) 160

505430-BTG-P-0316
Johnson Controls Unitary Products 15
Unit Limitations
1. Rated in accordance with AHRI Standard 110, Range “A” Utilization Voltage.
†. Low Ambient accessories are available to permit stable system operation at ambient temperatures down to 0°F.
Condenser Unit limitations
Size
(Tons) Model Unit Voltage Applied Voltage1Outdoor DB Temp
Cooling (°F) Indoor DB Temp Cooling (°F) Outdoor DB Temp Heating (°F) Indoor DB Temp Heating (°F)
Min Max Max Min†Max Min Max Min Max Min
-07 (7.5) PH 208/230-3-60 187 252 125 40 86 68 70 0 80 50460-3-60 432 504
575-3-60 540 630
-07 (7.5) YH 208/230-3-60 187 252 125 40 86 68 - - - -460-3-60 432 504
575-3-60 540 630
-10
(10) PH 208/230-3-60 187 252 125 40 86 68 70 0 80 50460-3-60 432 504
575-3-60 540 630
-10
(10) YH/YJ 208/230-3-60 187 252 125 40 86 68 - - - -460-3-60 432 504
575-3-60 540 630
-12
(12.5) YH/YJ 208/230-3-60 187 252 125 40 86 68 - - - -460-3-60 432 504
575-3-60 540 630
-15
(15) PH/PJ 208/230-3-60 187 252 125 40 86 68 70 0 80 50460-3-60 432 504
575-3-60 540 630
-15
(15) YH/YJ 208/230-3-60 187 252 125 40 86 68 - - - -460-3-60 432 504
575-3-60 540 630
-20
(20) PH/PJ 208/230-3-60 187 252 125 40 86 68 70 0 80 50460-3-60 432 504
575-3-60 540 630
-20
(20) YH/YJ 208/230-3-60 187 252 125 40 86 68 - - - -460-3-60 432 504
575-3-60 540 630
-25
(25) YH 208/230-3-60 187 252 125 40 86 68 - - - -460-3-60 432 504
575-3-60 540 630

505430-BTG-P-0316
16 Johnson Controls Unitary Products
Air Handling Unit Limitations
Model Power Supply Voltage Voltage Variation SupplyAir Range CFM Entering Air Temperature Degrees °F
Cooling
DB/WB Heating DB1
1Heating Min/Max temperatures apply to steam and hot water coils. NOTE: Do not apply steam to hot water coils.
Min. Max. Min. Max. Min. Max. Min. Max.
NH-07
208/230-3-60 187 253 2,250 3,750 65/57 90/77 40 80
460-3-60 414 506 2,250 3,750 65/57 90/77 40 80
575-3-60 540 630 2,250 3,750 65/57 90/77 40 80
NH-10
208/230-3-60 187 253 3,000 5,000 65/57 90/77 40 80
460-3-60 414 506 3,000 5,000 65/57 90/77 40 80
575-3-60 540 630 3,000 5,000 65/57 90/77 40 80
NJ-10
208/230-3-60 187 253 3,000 5,000 65/57 90/77 40 80
460-3-60 414 506 3,000 5,000 65/57 90/77 40 80
575-3-60 540 630 3,000 5,000 65/57 90/77 40 80
NH-15
208/230-3-60 187 253 4,500 7,500 65/57 90/77 40 80
460-3-60 414 506 4,500 7,500 65/57 90/77 40 80
575-3-60 540 630 4,500 7,500 65/57 90/77 40 80
NJ-15
208/230-3-60 187 253 4,500 7,500 65/57 90/77 40 80
460-3-60 414 506 4,500 7,500 65/57 90/77 40 80
575-3-60 540 630 4,500 7,500 65/57 90/77 40 80
NH-20
208/230-3-60 187 253 6,000 10,000 65/57 90/77 40 80
460-3-60 414 506 6,000 10,000 65/57 90/77 40 80
575-3-60 540 630 6,000 10,000 65/57 90/77 40 80
NJ-20
208/230-3-60 187 253 6,000 10,000 65/57 90/77 40 80
460-3-60 414 506 6,000 10,000 65/57 90/77 40 80
575-3-60 540 630 6,000 10,000 65/57 90/77 40 80
NH-25
208/230-3-60 187 253 8,000 12,000 65/57 90/77 40 80
460-3-60 414 506 8,000 12,000 65/57 90/77 40 80
575-3-60 540 630 8,000 12,000 65/57 90/77 40 80

505430-BTG-P-0316
Johnson Controls Unitary Products 17
Cooling and Heating Ratings
LEGEND
EER = Energy Efficiency Ratio
AHRI = Air Conditioning and Refrigeration Institute
IPLV = Integration Part-Load Value
IEER = Integrated Energy Efficiency Ratio
Cooling And Heating Rating
Outdoor Unit
Condensing Unit Only
Indoor
Unit
System Cooling Capacity1
1Certified in accordance with the Unitary Large Equipment certification program, which is based on AHRI Standard 340/360.(Except
YH-25)
Heating Capacity1
Rated
Airflow
(CFM)
Gross Capacity2
(MBH)
2Condensing unit only ratings are at 45°F SST and 95°F entering-air temperature.
KW EER Gross Capacity3
(MBH)
3Gross capacity does not include heat added by blower motor. Refer to appropriate table for blower horsepower.
EER IEER IPLV
High Outdoor Low Outdoor
Gross
Capacity2
(MBh) COP Gross
Capacity2
(MBh) COP
PH-074
4Heat Pumps designed for matched systems only.
N/A N/A N/A NH-07 92 11.0 11.4 --- 82 3.3 49 2.3 3000
PH-104N/A N/A N/A NH-10 124 11.0 11.4 11.8 109 3.3 63 2.1 4000
PH-154N/A N/A N/A NH-15 180 10.6 11.5 12.4 168 3.3 104 2.3 6000
PJ-154N/A N/A N/A NJ-15 180 10.6 11.5 12.0 168 3.4 103 2.4 6000
PJ-204N/A N/A N/A NJ-20 238 10.6 11.7 12.1 220 3.4 124 2.2 8000
YH-07 85 6.8 12.4 NH-07 94 11.2 13.0 --- N/A N/A N/A N/A 3000
YH-07 85 6.8 12.4 NH-10 99 11.9 13.0 --- N/A N/A N/A N/A 3000
YH-10 110 9.3 11.9 NH-10 124 11.4 12.5 12.9 N/A N/A N/A N/A 4000
YJ-10 108 9.1 11.8 NJ-10 124 11.2 11.2 11.6 N/A N/A N/A N/A 4000
YH-12 133 11.6 11.5 NH-15 150 11.0 13.3 13.8 N/A N/A N/A N/A 5000
YJ-12 136 11.5 11.8 NJ-15 150 11.0 12.1 12.3 N/A N/A N/A N/A 5000
YH-15 160 13.4 12.0 NH-15 181 11.2 12.2 12.5 N/A N/A N/A N/A 6000
YH-15 160 13.4 12.0 NH-20 190 11.7 12.7 12.5 N/A N/A N/A N/A 6000
YJ-15 166 12.3 13.4 NJ-15 181 11.2 11.6 12.4 N/A N/A N/A N/A 6000
YJ-15 166 12.3 13.4 (2)NH-07 187 11.2 -- -- N/A N/A N/A N/A 6000
YJ-15 166 12.3 13.4 (2)NH-10 187 11.2 -- -- N/A N/A N/A N/A 6000
YJ-15 166 12.3 13.4 NJ-20 190 11.7 13.4 11.2 N/A N/A N/A N/A 6000
YH-20 233 17.5 13.2 NH-20 242 11.3 13.6 13.1 N/A N/A N/A N/A 8000
YJ-20 222 17.3 12.8 NJ-20 242 11.3 11.9 12.6 N/A N/A N/A N/A 8000
YJ-20 222 17.3 12.8 (2)NH-10 240 11.6 -- -- N/A N/A N/A N/A 8000
YH-25 271 23.7 11.4 NH-25 299 10.2 12.2 -- N/A N/A N/A N/A 10000

505430-BTG-P-0316
18 Johnson Controls Unitary Products
Capacity Performance
Condenser and Air Handling Cooling Capacities
YH-07/NH-07
Air on
Evaporator Coil Temperature of Air on Condenser Coil
Total
Capacity1
(MBh)
Total
Input
(kW)2
Sensible Capacity (MBh) Total
Capacity1
(MBh)
Total
Input
(kW)2
Sensible Capacity (MBh)
CFM WB
(°F) Return Dry Bulb (°F) Return Dry Bulb (°F)
90 85 80 75 70 65 90 85 80 75 70 65
75°F 85°F
2250
77 110.8 6.0 51.5 42.0 32.6 - - - 107.2 6.5 49.8 40.4 30.9 - - -
72 103.3 5.7 66.5 57.0 47.6 38.1 - - 99.9 6.3 64.9 55.4 46.0 36.5 - -
67 95.9 5.5 81.5 72.0 62.6 53.1 43.6 - 92.6 6.2 80.0 70.5 61.0 51.6 42.1 -
62 88.0 5.4 88.0 86.3 76.8 67.3 57.8 48.3 84.8 6.1 84.8 83.9 74.5 65.0 55.5 46.1
57 77.7 5.2 77.7 77.7 72.2 62.8 53.3 43.8 80.1 6.0 80.1 80.1 73.1 63.6 54.2 44.7
2625
77 114.0 6.0 56.3 45.6 34.8 - - - 110.2 6.5 54.6 44.0 33.3 - - -
72 106.3 5.7 72.3 61.6 50.9 40.1 - - 102.7 6.3 70.8 60.2 49.6 38.9 - -
67 98.7 5.4 88.4 77.6 66.9 56.2 45.5 - 95.2 6.2 87.1 76.4 65.8 55.2 44.5 -
62 90.6 5.4 90.6 89.7 82.2 71.9 60.7 50.0 87.1 6.1 87.1 86.7 80.3 69.6 59.0 48.3
57 79.9 5.2 79.9 79.9 77.2 67.3 55.8 45.0 82.3 6.0 82.3 82.3 78.8 68.2 57.5 46.9
3000
77 117.2 5.9 61.0 49.1 37.1 - - - 113.1 6.5 59.4 47.5 35.7 - - -
72 109.3 5.7 78.1 66.2 54.2 42.2 - - 105.4 6.4 76.8 65.0 53.1 41.3 - -
67 101.4 5.4 95.2 83.2 71.3 59.3 47.3 - 97.7 6.2 94.2 82.4 70.5 58.7 46.9 -
62 93.1 5.4 93.1 93.1 87.5 76.5 63.6 51.6 89.5 6.1 89.5 89.5 86.1 74.2 62.4 50.6
57 82.2 5.2 82.2 82.2 82.2 71.7 58.3 46.3 84.5 6.0 84.5 84.5 84.5 72.7 60.8 49.0
3375
72 109.2 5.8 83.0 70.2 57.3 44.4 - - 105.4 6.4 81.6 68.8 56.0 43.2 - -
67 101.3 5.5 98.2 88.2 75.3 62.5 49.6 - 97.7 6.3 96.0 87.2 74.3 61.5 48.7 -
62 93.0 5.5 93.0 93.0 90.2 77.8 64.5 51.6 89.5 6.2 89.5 89.5 87.8 75.0 62.1 49.3
57 82.1 5.3 82.1 82.1 82.1 70.0 56.4 43.5 84.5 6.1 84.5 84.5 84.5 71.7 58.9 46.0
3750
72 109.1 5.9 87.9 74.2 60.4 46.6 - - 105.5 6.5 86.5 72.6 58.8 45.0 - -
67 101.2 5.6 101.2 93.2 79.4 65.7 51.9 - 97.8 6.3 97.8 91.9 78.1 64.3 50.5 -
62 92.9 5.6 92.9 92.9 92.9 79.1 65.3 51.6 89.5 6.2 89.5 89.5 89.5 75.7 61.9 48.1
57 82.0 5.4 82.0 82.0 82.0 68.2 54.4 40.7 84.5 6.1 84.5 84.5 84.5 70.7 56.9 43.1
95°F 105°F
2250
77 103.7 6.9 48.1 38.7 29.2 - - - 99.2 8.0 47.5 38.1 28.6 - - -
72 96.5 6.9 63.3 53.8 44.4 35.0 - - 92.2 8.0 62.1 52.6 43.2 33.7 - -
67 89.4 6.9 78.4 69.0 59.5 50.1 40.7 - 85.2 8.0 76.6 67.2 57.7 48.3 38.8 -
62 81.6 6.7 81.6 81.6 72.1 62.7 53.3 43.8 77.9 7.7 77.9 77.9 69.2 59.7 50.3 40.9
57 82.5 6.7 82.5 82.5 74.0 64.5 55.1 45.7 78.8 7.8 78.8 78.8 70.0 60.5 51.1 41.6
2625
77 106.4 7.0 52.9 42.3 31.8 - - - 101.7 8.1 53.5 41.7 31.1 - - -
72 99.0 7.0 69.4 58.8 48.2 37.7 - - 94.5 8.1 68.1 57.5 46.9 36.3 - -
67 91.7 6.9 85.8 75.3 64.7 54.1 43.6 - 87.3 8.0 82.8 73.3 62.7 52.1 41.5 -
62 83.7 6.8 83.7 83.7 78.4 67.3 57.2 46.7 79.9 7.8 79.9 79.9 75.2 64.4 54.0 43.4
57 84.6 6.7 84.6 84.6 80.4 69.1 59.2 48.7 80.7 7.9 80.7 80.7 76.1 65.1 54.8 44.2
3000
77 109.0 7.1 57.7 46.0 34.3 - - - 104.1 8.1 59.4 45.4 33.6 - - -
72 101.5 7.0 75.5 63.8 52.1 40.4 - - 96.8 8.1 74.2 62.5 50.7 38.9 - -
67 94.0 7.0 93.3 81.5 69.8 58.1 46.4 - 89.4 8.1 89.0 79.5 67.8 56.0 44.3 -
62 85.8 6.8 85.8 85.8 84.6 72.0 61.2 49.5 81.8 7.9 81.8 81.8 81.2 69.0 57.7 46.0
57 86.8 6.8 86.8 86.8 86.8 73.6 63.4 51.7 82.7 7.9 82.7 82.7 82.1 69.6 58.6 46.9
3375
72 101.7 7.1 80.2 67.5 54.7 41.9 - - 96.9 8.1 79.2 66.3 53.5 40.7 - -
67 94.2 7.0 93.8 86.1 73.3 60.5 47.7 - 89.5 8.1 89.4 83.7 71.5 58.7 45.8 -
62 86.0 6.8 86.0 86.0 85.4 72.1 59.8 47.0 82.0 7.9 82.0 82.0 81.7 68.6 56.0 43.2
57 86.9 6.8 86.9 86.9 86.9 73.4 61.4 48.6 82.8 7.9 82.8 82.8 82.6 69.3 56.9 44.1
3750
72 101.9 7.1 85.0 71.1 57.3 43.4 - - 97.1 8.1 84.1 70.2 56.3 42.4 - -
67 94.3 7.0 94.3 90.7 76.8 62.9 49.1 - 89.7 8.1 89.7 87.9 75.3 61.4 47.4 -
62 86.1 6.9 86.1 86.1 86.1 72.3 58.4 44.5 82.1 7.9 82.1 82.1 82.1 68.2 54.3 40.4
57 87.1 6.9 87.1 87.1 87.1 73.2 59.4 45.5 83.0 7.9 83.0 83.0 83.0 69.1 55.2 41.2

505430-BTG-P-0316
Johnson Controls Unitary Products 19
115°F 125°F
2250
77 94.7 9.0 46.9 37.5 28.0 - - - 90.2 10.1 46.3 36.9 27.4 - - -
72 87.8 9.1 60.9 51.4 42.0 32.5 - - 83.4 10.2 59.7 50.2 40.8 31.3 - -
67 80.9 9.1 74.8 65.4 55.9 46.5 37.0 - 76.7 10.3 73.0 63.6 54.1 44.6 35.2 -
62 74.3 8.8 74.3 74.3 66.2 56.8 47.3 37.9 70.6 9.9 70.6 70.6 63.3 53.8 44.3 34.9
57 75.0 8.9 75.0 75.0 66.0 56.5 47.0 37.6 71.3 10.0 71.3 71.3 61.9 52.5 43.0 33.5
2625
77 97.0 9.1 54.0 41.1 30.5 - - - 92.3 10.1 54.6 40.5 29.8 - - -
72 89.9 9.1 66.9 56.3 45.6 35.0 - - 85.3 10.2 65.7 55.0 44.3 33.7 - -
67 82.8 9.2 79.8 71.4 60.8 50.2 39.5 - 78.4 10.3 76.8 69.5 58.9 48.2 37.5 -
62 76.1 8.8 76.1 76.1 72.0 61.4 50.8 40.1 72.2 9.9 72.2 72.2 68.9 58.4 47.5 36.9
57 76.8 9.0 76.8 76.8 71.7 61.1 50.5 39.8 72.9 10.1 72.9 72.9 67.4 57.1 46.1 35.4
3000
77 99.2 9.1 61.1 44.7 32.9 - - - 94.3 10.2 62.8 44.1 32.2 - - -
72 92.0 9.2 72.9 61.1 49.3 37.5 - - 87.2 10.3 71.7 59.8 47.9 36.1 - -
67 84.8 9.2 84.8 77.5 65.7 53.9 42.1 - 80.2 10.3 80.2 75.5 63.6 51.8 39.9 -
62 77.8 8.9 77.8 77.8 77.8 66.0 54.2 42.4 73.8 9.9 73.8 73.8 73.8 63.0 50.7 38.8
57 78.6 9.0 78.6 78.6 77.5 65.7 53.9 42.1 74.5 10.1 74.5 74.5 72.9 61.8 49.1 37.3
3375
72 92.2 9.2 78.1 65.2 52.3 39.4 - - 87.4 10.2 77.0 64.1 51.2 38.2 - -
67 84.9 9.2 84.9 81.3 69.7 56.8 44.0 - 80.3 10.3 80.3 78.9 67.9 55.0 42.1 -
62 78.0 8.9 78.0 78.0 78.0 65.1 52.2 39.3 74.0 9.9 74.0 74.0 74.0 61.5 48.4 35.4
57 78.7 9.0 78.7 78.7 78.2 65.3 52.4 39.5 74.6 10.1 74.6 74.6 73.8 61.3 47.9 35.0
3750
72 92.3 9.1 83.3 69.3 55.4 41.4 - - 87.5 10.2 82.4 68.4 54.4 40.4 - -
67 85.1 9.2 85.1 85.1 73.8 59.8 45.8 - 80.4 10.3 80.4 80.4 72.2 58.2 44.2 -
62 78.1 8.9 78.1 78.1 78.1 64.1 50.2 36.2 74.1 9.9 74.1 74.1 74.1 60.1 46.1 32.1
57 78.9 9.0 78.9 78.9 78.9 64.9 51.0 37.0 74.8 10.0 74.8 74.8 74.8 60.8 46.8 32.8
1These capacities are gross ratings. For net capacity, deduct supply air blower motor, MBh. Example: Refer to the appropriate Blower
Performance Table for the BHP of the supply air blower motor, MBh = 3.415 x kW and kW = BHP x 0.746 nameplate rated motor
efficiency.
2These ratings include the condenser fan motors and the compressor motors but not the supply air blower motor.
YH-07/NH-07 (Continued)
Air on
Evaporator Coil Temperature of Air on Condenser Coil
Total
Capacity1
(MBh)
Total
Input
(kW)2
Sensible Capacity (MBh) Total
Capacity1
(MBh)
Total
Input
(kW)2
Sensible Capacity (MBh)
CFM WB
(°F) Return Dry Bulb (°F) Return Dry Bulb (°F)
90 85 80 75 70 65 90 85 80 75 70 65

505430-BTG-P-0316
20 Johnson Controls Unitary Products
YH-07/NH-10
Air on
Evaporator Coil Temperature of Air on Condenser Coil
Total
Capacity1
(MBh)
Total
Input
(kW)2
Sensible Capacity (MBh) Total
Capacity1
(MBh)
Total
Input
(kW)2
Sensible Capacity (MBh)
CFM WB
(°F) Return Dry Bulb (°F) Return Dry Bulb (°F)
90 85 80 75 70 65 90 85 80 75 70 65
75°F 85°F
2250
77 105.1 6.0 49.2 40.2 31.1 - - - 108.2 6.6 50.3 41.2 32.1 - - -
72 100.1 5.8 63.3 54.2 45.1 36.0 - - 101.4 6.5 63.6 54.6 45.5 36.4 - -
67 95.1 5.7 77.3 68.2 59.1 50.0 40.9 - 94.6 6.3 77.0 67.9 58.8 49.7 40.7 -
62 87.9 5.6 87.9 80.9 71.8 62.7 53.7 44.6 87.7 6.2 87.7 80.9 71.8 62.7 53.7 44.6
57 83.1 5.5 83.1 83.1 76.8 67.7 58.6 49.5 84.1 6.2 84.1 84.1 77.2 68.2 59.1 50.0
2625
77 109.8 6.0 53.6 43.4 33.2 - - - 112.0 6.7 54.5 44.3 34.1 - - -
72 104.5 5.9 68.6 58.3 48.1 37.9 - - 105.0 6.5 68.6 58.4 48.3 38.1 - -
67 99.3 5.7 83.5 73.3 63.1 52.9 42.6 - 97.9 6.4 82.8 72.6 62.4 52.2 42.1 -
62 91.8 5.6 91.8 86.9 76.7 66.8 56.2 46.0 90.7 6.2 90.7 86.4 76.2 66.0 55.8 45.7
57 86.7 5.6 86.7 86.7 82.0 72.3 61.5 51.3 87.1 6.2 87.1 87.1 82.0 71.8 61.6 51.4
3000
77 114.5 6.1 58.0 46.6 35.3 - - - 115.8 6.7 58.7 47.4 36.1 - - -
72 109.0 5.9 73.9 62.5 51.2 39.8 - - 108.5 6.6 73.6 62.3 51.1 39.8 - -
67 103.5 5.8 89.8 78.4 67.1 55.7 44.4 - 101.2 6.4 88.6 77.3 66.0 54.7 43.4 -
62 95.7 5.7 95.7 92.9 81.5 70.8 58.8 47.5 93.8 6.3 93.8 91.9 80.6 69.3 58.0 46.7
57 90.4 5.6 90.4 90.4 87.1 76.9 64.4 53.1 90.0 6.3 90.0 90.0 86.7 75.4 64.1 52.8
3375
72 110.2 6.0 77.6 65.3 53.1 40.8 - - 110.3 6.6 77.7 65.4 53.2 40.9 - -
67 104.6 5.8 94.1 81.8 69.5 57.3 45.0 - 102.9 6.5 93.3 81.0 68.8 56.5 44.3 -
62 96.7 5.7 96.7 95.3 84.5 72.6 60.0 47.7 95.3 6.3 95.3 94.4 84.0 71.7 59.5 47.2
57 91.4 5.6 91.4 91.4 89.8 78.0 65.2 53.0 91.5 6.3 91.5 91.5 89.8 77.6 65.3 53.1
3750
72 111.4 6.0 81.3 68.1 54.9 41.8 - - 112.1 6.6 81.7 68.5 55.3 42.1 - -
67 105.8 5.9 98.4 85.2 72.0 58.8 45.6 - 104.5 6.5 97.9 84.7 71.5 58.3 45.1 -
62 97.8 5.7 97.8 97.8 87.5 74.3 61.1 47.9 96.8 6.4 96.8 96.8 87.3 74.1 60.9 47.7
57 92.4 5.7 92.4 92.4 92.4 79.2 66.0 52.8 93.0 6.3 93.0 93.0 93.0 79.8 66.6 53.4
95°F 105°F
2250
77 111.4 7.2 51.3 42.3 33.2 - - - 107.2 8.2 49.9 40.9 31.8 - - -
72 102.8 7.1 64.0 54.9 45.9 36.8 - - 99.1 8.0 62.6 53.5 44.5 35.4 - -
67 94.2 7.0 76.7 67.6 58.5 49.5 40.4 - 90.9 7.9 75.3 66.2 57.1 48.1 39.0 -
62 87.4 6.8 87.4 80.9 71.8 62.7 53.6 44.6 84.0 7.8 84.0 79.3 70.2 61.1 52.0 43.0
57 85.2 6.8 85.2 85.2 77.7 68.6 59.6 50.5 82.3 7.7 82.3 82.3 74.9 65.8 56.8 47.7
2625
77 114.2 7.3 55.3 45.2 35.0 - - - 110.2 8.3 53.9 43.8 33.6 - - -
72 105.4 7.2 68.7 58.5 48.4 38.2 - - 101.8 8.1 67.4 57.2 47.0 36.9 - -
67 96.6 7.0 82.1 71.9 61.8 51.6 41.5 - 93.4 8.0 80.8 70.6 60.5 50.3 40.1 -
62 89.6 6.9 89.6 85.9 75.8 65.3 55.5 45.3 86.3 7.9 86.3 83.7 74.3 63.9 53.9 43.8
57 87.4 6.8 87.4 87.4 82.0 71.3 61.7 51.6 84.6 7.8 84.6 84.6 79.3 68.8 58.9 48.8
3000
77 117.1 7.3 59.3 48.1 36.9 - - - 113.1 8.3 58.0 46.7 35.5 - - -
72 108.0 7.2 73.4 62.2 50.9 39.7 - - 104.5 8.2 72.1 60.9 49.6 38.4 - -
67 99.0 7.1 87.5 76.2 65.0 53.8 42.5 - 95.9 8.1 86.3 75.0 63.8 52.5 41.3 -
62 91.9 6.9 91.9 91.0 79.7 67.9 57.3 46.0 88.6 7.9 88.6 88.2 78.3 66.8 55.8 44.6
57 89.6 6.9 89.6 89.6 86.3 74.0 63.8 52.6 86.9 7.8 86.9 86.9 83.6 71.8 61.1 49.8
3375
72 110.4 7.2 77.7 65.5 53.3 41.1 - - 106.7 8.2 76.4 64.2 52.0 39.7 - -
67 101.2 7.1 92.5 80.2 68.0 55.8 43.6 - 97.9 8.1 91.3 79.0 66.8 54.6 42.3 -
62 93.9 7.0 93.9 93.4 83.4 70.9 59.0 46.8 90.5 8.0 90.5 90.3 82.0 69.7 57.6 45.3
57 91.5 6.9 91.5 91.5 89.9 77.1 65.5 53.2 88.7 7.9 88.7 88.7 87.1 74.6 62.6 50.4
3750
72 112.8 7.3 82.1 68.9 55.7 42.4 - - 108.9 8.3 80.8 67.6 54.3 41.1 - -
67 103.3 7.1 97.4 84.2 71.0 57.8 44.6 - 100.0 8.1 96.3 83.0 69.8 56.6 43.4 -
62 95.9 7.0 95.9 95.9 87.1 73.9 60.7 47.5 92.4 8.0 92.4 92.4 85.8 72.5 59.3 46.1
57 93.5 6.9 93.5 93.5 93.5 80.3 67.1 53.9 90.5 7.9 90.5 90.5 90.5 77.3 64.1 50.9