Johnson Controls Holis JSE04-T02-BI01 User manual

Figure 3: Micro SD card slot and reset button (continued)
Note: Remove the two screws on the camera cover (1) (Figure 3) to access
the buttons. Securely attach the cover when finished.
Table 3: Micro SD card slot and reset button descriptions
Number
Camera button description
1
Camera button cover
2
Micro SD Card slot
3
Reset button (Hold for more than 3 seconds)
Quick reference
Default IP: 192.168.1.168 (DHCP enabled).
Default Username / Password: admin / admin
Power: DC12V or PoE
Use Internet Explorer 11 web browser.
Mounting the camera to a wall or ceiling
Ensure that the wall or ceiling is strong enough to withstand three times the
weight of the camera.
1. Place the mounting template on the surface that you want to attach
the camera.
2. On the surface drill three Ø 4.5mm holes and cut out a cable hole as
per the markings identified on the mounting template.
3. Securely place the three screw anchors into the three holes.
4. Place the camera cable through the cable hole on the mounting
surface and ensure that the three cable side entry plugs are inserted
into the three slots on the camera base (2) (Figure 1).
OR
Use a cable side entry hole slot (3) (Figure 1) on the camera base
and ensure that two of the cable side entry plugs are inserted into the
remaining two slots on the camera base.
Security
Quick Start Guide
(8200-1994-01_D0)
Tyco Holis JSE Economical 4MP Turret Camera
(Product Code: JSE04-T02-BI01)
In the box
1 x Camera
1 x Quick Start Guide
3 x PA 4x25mm Tapping screws
1 x L-Key Hexagonal wrench
1 x Mounting template
3 x 6x25mm Plastic screw anchors
3 x Silicone plugs
1 x Regulatory Document
Installation tools
Screwdriver
Drill
L-Key Hexagonal wrench
Figure 1: Camera parts
Figure 1
Table 1: Camera part descriptions
Number
Camera part description
1
Camera lens
2
Camera base
3
Cable side entry slot
4
Fixed screw
Figure 2: Cable connections
Figure 2
Table 2: Cable connection descriptions
Number
Cable connection description
1
Ethernet Connector and also supports PoE
2
Power Connector (12V DC @ 1A)
Figure 3: Micro SD card slot and reset button
Figure 3
Mounting the camera to a wall or ceiling (continued)
5. Hold the camera up to the mounting template and align the three
holes on the camera base with the three holes on the mounting
surface.
6. Insert the three tapping screws into the three holes on the camera
base and securely attach the camera to the mounting surface.
7. To power up the camera:
Connect a 12V DC power supply to the power connector on the
camera cable.
OR
Connect a shielded PoE cable to the ethernet / PoE slot on the
camera cable.

Security
Adjusting the camera position
1. Use the L-key hexagonal wrench to:
i. Unlock the screw (1) (Figure 4) and pan the camera field of
view up to 360 degrees.
Figure 4
Note: You must securely lock the screw to ensure that the camera holds
the modified position.
Adjusting the camera zoom and focus
1. Use the screwdriver to remove the two screws on the cover.
2. Rotate the ‘Focus’and / or ‘Zoom’buttons (Figure 5) as desired.
Figure 5
Note: You must securely attach the cover when finished adjusting the
Focus or Zoom.
Warnings
If the product does not work properly, please contact your dealer
or the nearest service centre. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the
product is mounted on wall or ceiling, the device shall be firmly
fixed.
Do not allow water or liquid intrusion into the camera.
Do not use camera beyond specified voltage range.
Do not drop the camera or subject it to physical shock.
Avoid touching the camera lens.
If cleaning is necessary, please use clean cloth to wipe it gently.
Do not aim the camera at the sun or extra bright place.
Do not place the camera in extremely hot, cold (the operating
temperature shall be -30˚C~60˚C), dusty or damp locations, and
do not expose it to high electromagnetic radiation.
To avoid heat accumulation, good ventilation is required for
operating environment.
© 2021 Johnson Controls. All rights reserved.
JOHNSON CONTROLS, TYCO, and HOLIS are trademarks and/or
registered trademarks. Unauthorized use is strictly prohibited.