Johnson 40-6301 User manual

40-6301 Laser Mounting Pole
with Tripod Assembly Instructions
Download this manual at
www.johnsonlevel.com/manuals
40-6301
SPRING LOADED
FLOOR POLE
TRIPOD
CARRYING CASE
LASER MOUNTING PLATFORM
1/4" - 20 ADAPTER
CEILING
POLE
TELESCOPING
CENTER
POLES (3)
Thank you for purchasing this 40-6301 Laser
Mounting Pole with Tripod.
1. Locate tripod and unlock the black plastic clamp on the leg (A) to
extend to your desired height (B). Lock the clamp to keep leg in this
fixed position. Repeat for the other the two legs.
2. Locate spring loaded floor pole and insert through tripod center
holes from the bottom (C). If pole doesn’t slide through top hole,
then loosen tripod locking screw by turning counterclockwise (D).
Do not remove locking screw. Position tripod in upright position with
spring loaded end on the floor (E).
5. Locate laser mounting platform (L). Unlock the quick release lock by
moving lock to an upward position and hold in the highest upward
position. Attach laser mounting platform to threaded end of center
pole column (M). To lock onto pole, push lock downward (N). Assemble
remaining center pole or poles together as needed for jobsite height
requirement (O) and attach to assembled center pole in tripod.
6. Unlock and slide laser mounting platform to desired
position on pole for laser or optical instrument. Lock into
position by pushing quick release downward.
7. For greatest stability, extend legs to the farthest position.
Fully lock tripod locking screw (P). Assembly is complete (Q).
4. IF 1/4" - 20 adapter is not required, skip to #5. To use included 1/4"-20
adapter for laser or optical instrument (G), use 3/16" Phillips head
screwdriver. Unscrew both screws on bottom (H) and remove 5/8"-11
adapter (I). Install 1/4"-20 adapter (J), use same screws and install
onto bottom of adapter (K).
3. Use leveling vial to level tripod and make
adjustment to each leg as needed (F).
5 Telescoping Poles
3 Center Poles
1 Spring Loaded Floor Pole
1 Ceiling Pole
Tripod
Laser Mounting Platform
1/4" - 20 Adapter
Carrying Case
C
L
G
A
D
P
M
H
F
B
E
N
I
O
J K
ASSEMBLY INSTRUCTIONS FOR
NON-FLOOR TO CEILING APPLICATION
KIT CONTENTS:
TRIPOD
LOCKING
SCREW
TRIPOD
LOCKING
SCREW
QUICK
RELEASE
LOCK
LASER
MOUNTING
SCREW
LEVELING VIAL
Q

Download this manual at
www.johnsonlevel.com/manuals
40-6301
40-6301 Laser Mounting Pole
with Tripod Assembly Instructions
ASSEMBLY INSTRUCTIONS FOR
FLOOR TO CEILING WITHOUT TRIPOD
1. Locate spring loaded floor pole, three center
poles and ceiling pole.
2. Assemble one center pole to spring loaded floor
pole (R).
3. Locate laser mounting platform. Unlock the quick release lock by moving
lock to an upward position and hold in the highest upward position.
Attach laser mounting platform to threaded end of center pole column (S).
To lock onto pole, push quick release lock downward (T).
4. Assemble additional center pole or poles as needed for overall floor to
ceiling height, attaching ceiling pole to threaded end on assembled center
pole(s) (U).
5. You can extend the overall height of the laser pole by twisting the black
connector piece on the end of the spring loaded pole (V). Rotate the black
connector piece 1/8" counterclockwise to unlock, extend and lock into
position (W) by turning clockwise. Note, the overall pole height should
be 1/4" – 1/2" longer than the ceiling height to allow for sucient spring
loaded pressure.
R
S
V
T
W
X
U
BLACK
CONNECTOR
PIECE
6. Place assembled laser pole into desired jobsite location, pressing
down to compress and release when in desired vertical floor to
ceiling position (X). Spring pressure should hold pole in position.
If not, repeat step 5 above to extend spring loaded floor pole for
additional height. Adjustment elevating range is 2.33' to 11'.
QUICK
RELEASE
LOCK
QUICK
RELEASE
LOCK