JRC NSVS1196 User manual

NSVS1196 Oct. 2008
Application
433.92MHz Resonator
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.2.
Maximum Rating: (Table 2)
C0
CMLMRM
Fig.1 RF Equivalent RLC Model
Mechanical Specifications: (Fig.2)
Package is designed as small as 3.0x3.0x1.15[mm3] for SMD (Surface Mount Device) type.
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
Table 1. Electrical Specifications (@25ºC)
Item Specification Typical
Center frequency Absolute frequency - 433.92 MHz
Tolerance from 433.92MHz ±50kHz max. -
Insertion Loss @Minimum Loss 2.5 dB max. -
Temperature Stability Turnover Temperature - 25 ºC
Temperature Coefficient - -0.04 ppm/ºC2
DC Insulation Resistance between any two terminals 1.0M ohm min. -
RF Equivalent Motional Resistance (RM) - 14.5 ohm
RLC Model (fig.1) Motional Inductance (LM)- 65.595 μH
Motional Capacitance (CM) - 2.05 fF
Shunt Static Capacitance (C0) - 2.902 pF
Table2. Maximum Ratings
Item Rating
Maximum Input Power 0dBm
Operating Temperature Range -40~+85ºC
Storage Temperature -40~+85ºC
JRC SAW RESONATOR
NSVS1196
Communications and Device Group
Communications Equipment Marketing Department
10-1, Nishi-Shinjuku 6-chome, Shinjuku-ku,
Tokyo, 160-8328 Japan
Tel. [phone]
Fax. [phone]
http://www.jrc.co.jp/jp/product/device/saw/index.html (Japanese)
http://www.jrc.co.jp/eng/product/saw/index.html (English)

NSVS1196 Oct. 2008
Marking
(1) Lot Number
(a) Year
(b) Month
*Oct.--- X
Nov.--- Y
Dec.--- Z
(c) Date
1-9--- 0
10-19--- 1
20-31--- 2
(2) Part Number Mark
Pin no. Connection
1 GND
2 IN
3 GND
4 GND
5 OUT｜
6 GND
(0.6)
(0.25)
(0.6)
(0.53)
(0.75)
(0.45)
1
2
34
6
1. 1 5 ± 0. 1 5
3. 0 ± 0. 1 5
3. 0 ± 0. 1 5
(a)
(1)
(b)
(2)
(1.80)
5
[2x]
[4x]
[4x]
(c)
Fig.1 Measuring circuit
Fig.2 Package dimensions (in mm)
Fig.3 Desirable land area (in mm)
8X1
IN
50Ω
OUT
50Ω
0.93
0.6
0.93
3.8
3.8
2.2 1.15
1.15
1
2
34
5
6
SAW

NSVS1196 Oct. 2008
Notice
1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than -40ºC or more than +85ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of soldering
iron: 350ºC max., the time of soldering: 10 seconds max., the power of
soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature of
this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static electricity to
this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.
Note
1. This specification specifies the quality of this component as a single unit.
Make sure that this component is evaluated and confirmed against this
specification when it is mounted to your products.
2. The information contained herein may be changed without prior notice. It is
therefore advisable to contact Japan Radio Company before proceeding with
the design of equipment incorporating this product.
3. The products are designed to be used with ordinary electronic equipment
(data and communications equipment, office equipment, audio-video
equipment, measuring instruments, etc). Japan Radio Company does not
assume any liability for the case using the products with the application
required high reliability or safety extremely (such as space equipment,
sea-bottom equipment, medical equipment etc). When intending to use any
our product please contact our sales representatives in advance.

0
6
12
18
24
30
S21
Insertion Loss [dB]
0
2
4
6
8
10
CH1 : center 433.92 span 1
CH2 : center 433.92 span 1
Insertion Loss [dB]
FREQUENCY CHARACTERISTICS
NSVS1196 Oct. 2008
S11 S22
S11 S22
1 1
3 3
5 5
7 7
9 9
11 11
433.4 433.4433.9 433.9434.4 434.4
Frequency [MHz] Frequency [MHz]
VSWR VSWR
NSVS971 Dec-04
Fig.1 Measuring circuit
13.30±0.20
6.5±0.20
(R0.3)
[4×]
(0.76)
(2.54)
(1.4)
(0.8)
[12×]
(2.54±0.15)
Pin No. Connection
1GND(PKG)
2GND(PKG)
3 GND(PKG)
4GND(PKG)
5OUT/IN
6 GND(signal)
7GND(PKG)
8GND(PKG)
9GND(PKG)
10 GND(PKG)
11 IN/OUT
12 GND(signal)
2.0 max.
(1)
(a) (b)
(3)
Marking
(1) Manufacture's Mark
(2) Lot Number
(a) Year
(b) Month
*Oct.--- X
Nov.--- Y
Dec.--- Z
(c) Date
1-9--- 0
10-19--- 1
20-31--- 2
(3) Part Number Mark
(1.26±0.13)
[12×]
[12×]
(2.54)
(R0.3)
(2.54±0.15)
(2)
12345
6
7
8
910
11
12
(C)
Fig.2 Package dimensions(in mm)
J4Y1
VS971
１２３４
10
９８７
11
12
６
５
OUT
50O
IN
50O
SAW
*27nH
*27nH
39pF
33pF
*murata LQW18A series