Crestron Avia DSP-1282 User manual

DSP-1282 &DSP-1283
CrestronAvia™ DSP with
Mitel® 8.0 PR3 Platform
ConfigurationGuide
CrestronElectronics,Inc.

The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at patents.crestron.com.
Certain Crestronproducts contain open source software. For specific information, visit www.crestron.com/opensource.
Crestron, the Crestron logo, Crestron Avia, and CrestronToolbox are eithertrademarks orregistered trademarks of
CrestronElectronics, Inc. in the United States and/or othercountries. Mitel is either a trademark or registered trademark
of Mitel Networks Corporation in the United States and/or other countries. Other trademarks, registered trademarks,
and trade names may be used in this document to refer to eitherthe entities claiming the marks and names ortheir
products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for
errors in typography or photography.
©2018 CrestronElectronics, Inc.

Contents
Introduction 1
Audience 1
Topology 1
Software Requirements 2
Hardware Requirements 2
Product Description 2
Summary 2
Crestron Avia DSP Configuration 4
Connections 4
Device Discovery/Access 4
Device Configuration 4
Configure the DSP Device 4
Configure the SIP Parameters 7
Mitel Configuration 8
Verify Licenses 8
Configure Codec Settings and Network Zones 9
Configure Network Element 10
Configure Class of Service 11
Configure SIP Device Capabilities 20
Configure Trunk Attributes 22
Configure SIPPeerProfile 23
Assign SIP Peer Profile by Incoming DID 28
Automatic Route Selection (ARS) Digit Modification Number 28
ARS Routes 29
ARS Digits Dialed 30
Configure a UserforEachDevice/Phone 31
Configure a Call Forwarding Profile 36
Configure the Ring Group 37
Configuration Guide — 8341B Contents • i

ii • Contents Configuration Guide — 8341B

Configuration Guide — 8341B DSP-1282 & DSP-1283: SIP Endpoint withMitel 8.0 PR3 • 1
DSP-1282 &DSP-1283:
SIPEndpointwith Mitel® 8.0 PR3
Platform
Introduction
This configurationguidedescribes theprocedures requiredto configureCrestronAvia™
DigitalSignalProcessor (DSP)devices.Thedevices operateon theMiVoiceBusiness (Mitel®
PBX)as basicSessionInitiationProtocol(SIP)users.
Audience
Theintendedaudienceincludes thoseattemptingtoconfigureanduseCrestron AviaDSP
devices as SIP endpoints registeredto MiVoiceBusiness (MitelPBX).
Topology
Thediagram belowshows thenetworktopologyfor integration ofaCrestron AviaDSP
endpointwithMiVoiceBusiness (MitelPBX).
SIP EndpointIntegrationwith MiVoice Business (Mitel PBX) - Reference Network

2 • DSP-1282 & DSP-1283: SIP Endpoint with Mitel 8.0 PR3 Configuration Guide — 8341B
Thelabnetwork consists of thefollowingcomponents:
lMitelPBX
lMitelphones
lCrestron AviaDSP as SIPusers
Software Requirements
lMiVoiceBusiness (MitelPBX):8.0PR3
lCrestronAviaDSP:v1.00.121
Hardware Requirements
lMiVoiceBusiness (MitelPBX)either inavirtualenvironment or with ahardware
server
lPublicSwitchedTelephoneNetwork(PSTN)gateway
lMiTelPhones - 5360IP phones (2)
lCrestron AviaDSP devices (2)
Product Description
TheCrestron AviaDSP products (DSP-1282andDSP-1283,specifically)consistof afamily
of programmabledigitalaudiosignalprocessors intendedfor thecommercialsound
market.Each version provides 12analogmic/lineinputs andeightanaloglineoutputs.The
devices includeaLocalAreaNetwork(LAN)connection andaUniversalSerialBus (USB)
connection for programmingandcontrol.Theprogrammablesignalflowis afixed
topologywithuser-configurableinput andoutputprocessingchains usingalibrary of
presetsignal-specific DSP blocks.
UsetheCrestronAviatooltocontrolandconfiguretheCrestron AviaDSP devices onthe
network.
UsetheCrestronToolbox™ softwaretodiscover andcontrolallCrestron devices on the
network.
Summary
This documentdescribes howtoconfiguretheCrestron AviaDSP devices as SIPusers.It
alsoprovides information onhowtoregister devices to theMitelPBXwithdigest
authentication.
Supportedfeatures include:
lRegistrationwithdigestauthentication
lBasic calls withG711u andG711acodecs
lDual-ToneMulti-Frequency(DTMF)support
lEarlymediasupport

Configuration Guide — 8341B DSP-1282 & DSP-1283: SIP Endpoint withMitel 8.0 PR3 • 3
lRetrievalof aparkedcall
lTransfereeinacalltransfer
lConferenceparticipant
lMember ofhuntgroup
lDND (Do Not Disturb)
Unsupportedfeatures include:
lCaller ID presentation
lCallholdandresume
lCallforwardingonthedevice(forwardingcanbeconfiguredonthePrivateBranch
Exchange(PBX)for theDomain Name(DN)assignedto theendpoint)
lCallwaiting
lInitiatingconference
lInitiatinganattendedcalltransfer
lInitiatinganearlyattendedcalltransfer
lInitiatingablindcalltransfer
lSharedline(configurationofsharedlineondevice)
lInitiatingcallpark
lMessageWaitingIndicator (MWI)
Knownissues andlimitations include:
lTheDSP does notsupportMusic onHoldwhenintegratedwiththeMitelPBX.
lNosupportfor caller IDon theCrestron AviaDSP.
lNosupportfor MWI ontheCrestronAviaDSP.
lWhenregisteredto Mitel,theDSP is not availableto acceptcalls after apower cycle
unless theprevious callis disconnected.
lIn aMitelenvironment,acalldeclinedbytheDSP does notprovideappropriate
treatmenttothecallingparty.
lTheDSP fails toplay areorder tonewhenacallfrom theDSP toaPBXextension
eventuallytimes outafter thecalledparty does not answer.

4 • DSP-1282 & DSP-1283: SIP Endpoint with Mitel 8.0 PR3 Configuration Guide — 8341B
CrestronAvia DSP Configuration
This section provides thefollowingdetails:
lHowtosetupconnections totheamplifier andspeaker
lHowtoaccess theDSPon thenetwork (oncepowered)
lHowtoconfiguretheDSPfor registrationandintegrationwiththeMitelPBX
Connections
Makethefollowingconnections:
lConnectmicrophonetoDSP MIC/LINEINPUTSport1
lConnect DSP LINE OUTPUTSport 1 to"AudioIn" onamplifier
lConnect"AudioOut" ofamplifier tospeaker
lConnectLAN port tonetwork
lConnectVOIP porttonetwork
DeviceDiscovery/Access
UsetheCrestronToolboxandtheCrestronAviatooltodiscover andaccess theconnected
LAN and/or VOIPports)DSPdevices.
UsetheHelpmenu toassistwhenperformingthediscoveryandconfigurationprocedure.
DeviceConfiguration
Thebasicsetupfor aphonecallrequires:
lAn analoginput(such as from amicrophone)routedout throughthephoneline
lAudio comingin from thephonelineroutedtoananalogoutput (such as to an
amplifier or speaker)
Configure the DSP Device
UsetheCrestronAviatooltoselectandconfiguretheDSP device.

Configuration Guide — 8341B DSP-1282 & DSP-1283: SIP Endpoint withMitel 8.0 PR3 • 5
InputConfiguration
Toconfiguretheanaloginput:
1. ClickSignal.
Crestron Aviatool: Audio InputConfiguration (1/4)
2. Under AnalogIn 1 (firstrow),doubleclickGain.Inthenewwindowsetthefollowing:
a. ClickMutetoOff.
b. Select33for theAnalogGain.
c. If acondenser microphoneis beingused,click+48V(phantompower)toOn.
Crestron AviaTool: AudioInputConfiguration(2/4)
3. Under AnalogIn 1 (firstrow),clickRef/PhoneOut (right-most column)andenter 0
as thedecibelvalue.
Crestron AviaTool: AudioInputConfiguration(3/4)
4. Under Phone\SigGenIn,clickPHN.Inthenewwindowsetthefollowing:
a. MovetheSendLevelslider to0db.
b. ClickMutetoOff.
Crestron AviaTool: AudioInputConfiguration(4/4)

6 • DSP-1282 & DSP-1283: SIP Endpoint with Mitel 8.0 PR3 Configuration Guide — 8341B
OutputConfiguration
Toconfiguretheanalogoutput:
1. Under PhoneIn 1 (firstrow),clickAnalogOut(left-most column)andenter 0as the
decibelvalue.
Crestron AviaTool: AudioOutputConfiguration(1/3)
2. Under AnalogOut1,doubleclickLVL.Inthenewwindowsetthefollowing:
a. MovetheLevelslider to0db.
b. ClickMutetoOff.
Crestron AviaTool: AudioOutputConfiguration(2/3)
3. Under Phone\SigGenIn,clickPHN.In thenewwindowsetthefollowing:
a. MovetheReceiveLevelslider to0db.
b. ClickMutetoOff.
Crestron AviaTool: AudioOutputConfiguration(3/3)