JS Automation DC2010 User manual

DC2010
Data Center
User’s Manual (V1.0)
健昇科技股份有限公司
JS AUTOMATION CORP.
新北市汐止區中興路 100 號6樓
6F., No.100, Zhongxing Rd.,
Xizhi Dist., New Taipei City, Taiwan
TEL：[phone]
FAX：[phone]
http://www.automation.com.tw
http://www.automation-js.com/
E-mail：[email protected].tw

1
Correction record
Version Record
1.0

2
Contents
1 Introduction..........................................................................................................................................4
1.1 Package contents......................................................................................................................4
2 Install hard disks..................................................................................................................................5
3 Hardware installation...........................................................................................................................8
3.1 Connecting to a single PC........................................................................................................8
3.2 Connecting to be accessible from Internet...............................................................................9
3.3 Connecting the power..............................................................................................................9
3.4 Connecting to UPS...................................................................................................................9
4 Configuration through front panel.....................................................................................................10
4.1 Familiar with the front panel operation.................................................................................10
4.2 How to operate the touch wheel ............................................................................................11
4.3 First boot up...........................................................................................................................13
4.4 System creation......................................................................................................................14
4.5 Entering parameter editing mode...........................................................................................15
4.6 System information from local panel.....................................................................................17
4.7 LCD backlight setting from local panel.................................................................................18
4.8 Screensaver time setting from local panel.............................................................................18
4.9 Network setting from local panel...........................................................................................19
4.10 USB backup setting from local panel....................................................................................21
4.11 Selection of input method......................................................................................................22
4.12 Password change setting from local panel.............................................................................23
4.13 Create system setting from local panel..................................................................................24
4.14 Restore system setting from local panel................................................................................24
4.15 System restart setting from local panel..................................................................................25
4.16 Shutdown DC2010 from local panel .....................................................................................25
4.17 AUTO shut down by UPS power lost....................................................................................26
5 Introduction to web storage manager.................................................................................................27
6 System information from web storage manager................................................................................29
6.1 Login the administration page ...............................................................................................29
6.2 System -> Overview ..............................................................................................................30
6.3 System -> Summary ..............................................................................................................31
7 System management from the web storage manager.........................................................................32
7.1 System Manager -> Date and Time.......................................................................................32
7.2 System Manager -> Network.................................................................................................35
7.3 System Manager -> Language...............................................................................................37
7.4 System Manager -> Administrator.........................................................................................38
7.5 System Manager -> Disk Manager........................................................................................39
7.6 System Manager -> DDNS....................................................................................................40
8 Access Right Management from the web storage manager...............................................................41

3
8.1 Access Right Management -> Group management...............................................................41
8.2 Access Right Management -> User management..................................................................43
8.3 Access Right Management -> File Sharing...........................................................................47
9 System service ...................................................................................................................................51
9.1 System Service -> FTP Service .............................................................................................51
9.2 System Service -> iTunes Service.........................................................................................52
9.3 System Service -> Backup.....................................................................................................54
9.4 System Service -> Log file....................................................................................................58
10 Application.....................................................................................................................................60
10.1 BitTorrent...............................................................................................................................60
10.2 Downloader............................................................................................................................65
11 System update....................................................................................................................................67

1 Introduction
Thank you for purchasing the DC2010 data center. This device is network attached file server
(NAS) with RAID1 auto backup. The operating system is a customized Linux based OS, which stored at
on board flash. For the ultimate safety, the power of the hard disks is separately powered.
This manual will bring you go through the detail operation of the device, from device connection,
local panel configuration and remote web configuration then the applications provided with the device.
You need some knowledge of the internet such as IP, TCP, hub, router, gateway. We will reference them
and make a brief explanation as required, if you want to know more detail please refer any web site that
supplies such kind knowledge.
1.1 Package contents
DC2010 *1 Power adaptor *1: 110/220Vac to 24Vdc
Hard disk cables *2 Power cord *1
Hard disk fixing screws *8
4

2 Installharddisks
Slide out the rack
1. Un-screw the screws as red circle shown.
2. Pull to slide out the rack from cover.
5

Install hard disks
3. Install the hard disk power and control cables
4. Screw to fix the hard disks.
5. Install the cables to the hard disks
6

Re-cover the device
6. Slide in the rack to the cover
7. Screw the bottom screws
8. Screw the rear panel screws
7

3 Hardwareinstallation
1. RS232: UPS communication connector
2. Power connector: +24Vdc power input connector
3. RJ45: Ethernet connector
3.1 Connecting to a single PC
DC2010 may work as an external safe storage of your PC, if you connect the DC2010 to your PC
only. In this environment, you cannot share files through network with others.
8

3.2 Connecting to be accessible from Internet
If your want to share files with others or you want to access files from anywhere provided Ethernet,
you must have an IP which is external accessible. The most possible configuration is as follows.
You need a gateway to control the external and internal message flow, and hub to switch the
intranet message flow. Currently on the market a ‘router’ will act as gateway and hub.
Please refer the gateway’s or router’s manual to configure your environment.
3.3 Connecting the power
If you use a UPS, please connect the power adaptor input power cord to the UPS output socket. If
you do not use the UPS, connect the input power cord to the power socket available. The power adaptor
comes with the DC2010 is a universal type; the power source may be 100/110Vac or 200/220Vac at
50/60 Hz. Then connect the adaptor output to DC2010 rear connector 24Vdc input.
3.4 Connecting to UPS
DC2010 has designed in UPS communication protocol with OPTI_UPS model VS375C. Connect
the DC2010 rear D type 9pin connector to the UPS 9 pin connector with standard RS232 cable. When
the power is lost, the UPS will inform the DC2010 to safely shut down; then if power recovered, the
UPS will inform the DC2010 to auto boot.
9

4 Configurationthroughfrontpanel
4.1 Familiar with the front panel operation
1. HDD: hard disk active indicator
2. UPS: UPS active indicator, when the rear RS232 connector successfully connect to OPTI-UPS
VS375C, the indicator will light.
3. ACT: ACT indicator flicks while power on but the DC2010 not active. While the device is
activated, the ACT will light.
4. LAN: Ethernet active connector, when the rear RJ45 Ethernet connects successfully.
5. LCD message display: display the information.
6. USB connector: USB2.0 connector for local USB backup.
7. Touch wheel: Thumb touch and slide to select displayed items.
8. Confirm button: Touch button for confirmation.
10

11
4.2 How to operate the touch wheel
Before we use touch wheel and confirmation button to input or correct the digits, let us take a brief
trip about the operation. There are two possible manual touch methods, rotate wheel or touch click. The
default is rotate wheel input method.
If the input is touch wheel, please refer the followings:
Touch wheel input method:
1. There are 2 cursors on the screen; the top lane cursor is the input cursor, the lower lane cursor is
the candidate cursor.
2. The cursor highlighted input digit is the digit available to input.
3. Touch the wheel and rotate right, the cursor on candidate digit will jump right.
4. Touch the wheel and rotate left, the cursor candidate digit will jump left.
5. ←Left shift: shift left the input space cursor.
6. →Right shift: shift right the input space cursor.
7. ↵Confirm: confirm the input data
8. ↑Return to upper level
Try an example of input; if the LCD message is on password input page, the device now is waiting
for your input.
P W D : _ _ _ _ _ _
0 1 2 3 45 6 7 8 9← → ↵↑
Say the password is 123456 (note that: the factory default is 000000), the process you will go:
A. Press the wheel and rotate the wheel to jump the candidate cursor to digit ‘1’then press the
confirmation button to enter the first digit while input cursor on first digit.
B. Press the wheel and rotate the wheel to jump the candidate cursor to digit ‘2’then press the
confirmation button to enter the second digit while input cursor on second digit.
C. Repeat the process until all the digits are input.
D. Move the candidate cursor to confirm, press confirmation button to input data to the device.
E. If you want to change any digit already input, rotate the touch wheel to move candidate
cursor to left shit or right shift and press confirmation button to shift the input cursor to the
digit you want to change. Input the new digit as process described above.

12
If the input method is touch click, refer the followings:
Touch click input method:
1. There are 2 cursors on the screen; the top lane cursor is the input cursor, the lower lane cursor is
the candidate cursor.
2. The cursor highlighted input digit is the digit available to input.
3. Touch the wheel left half ring; the cursor candidate digit will jump left.
4. Touch the wheel right half ring; the cursor candidate digit will jump left.
5. ←Left shift: shift left the input space cursor.
6. →Right shift: shift right the input space cursor.
7. ↵Confirm: confirm the input data
8. ↑Return to upper level ↵
Try an example of input; if the LCD message is on password input page, the device now is waiting
for your input.
P W D : _ _ _ _ _ _
0 1 2 3 45 6 7 8 9← → ↵↑
Say the password is 123456 (note that: the factory default is 000000), the process you will go:
A. Press the wheel ring left or right to jump the candidate cursor to digit ‘1’then press the
confirmation button to enter the first digit while input cursor on first digit.
B. Press the wheel ring left or right to jump the candidate cursor to digit ‘2’then press the
confirmation button to enter the second digit while input cursor on second digit.
C. Repeat the process until all the digits are input.
D. Move the candidate cursor to confirm, press confirmation button to input data to the device.
E. If you want to change any digit already input, click the touch wheel to move candidate
cursor to left shit or right shift and press confirmation button to shift the input cursor to the
digit you want to change. Input the new digit as process described above.
We will use the touch wheel as default configuration, any terms mentioned as rotate wheel
right or left is equivalent to click right or left.

4.3 First boot up
When power on, the front panel ACT indicator will be flicking to indicate power on but DC2010
not working. To start the DC2010 press the confirmation button more than 3 s. The LCD will display the
welcome message as follows:
D a t a C e n t e r
J S A u t o m a t i o n (Welcome message)
S y s t e m B o o t i n g
> > >
(System booting…)
Normally the system will be ready to serve within 2 minutes. After the system boot up, there are
two possible situations will be:
A. If first time boot up and hard disk have never formatted. The system will request to create
system.
C r e a t e S y s t e m
← →
B. If the system has already created and no error occurs, the message will be the IP you set. (in this
example the IP is : 192.168.0.168)
D C - 2 0 1 0
1 9 2 . 1 6 8 . 0 . 1 6 8
13

14
4.4 System creation
System creation will erase the data already on the hard disk and copy the operating system to hard
disk.
At first boot up system requires creating system. If system failure or manually request to create
system, you must make sure if you want to discard the data or you have data backed up somewhere.
The default configuration of the system is RAID1, we strongly recommended to use 2 disks of the
same model.
C r e a t e S y s t e m
← →
System creation
C r e a t e ?
Y e s ■ N o
If YES, confirm to create system
C h e c k D e v i c e
> > > > > >>
Proceed to verify the hard disks
D e v i ce E r r o r
C h e c k a n d R e r u n
If hard disk error, power off and try to re-install them
C r e a ti n g R A I D 1
> > > > >
If hard disk is OK, create system with RADI1 as default.
I n i t ia l S u c c e s s
I t w il l r e s t a r t
If system create OK, the system will auto re-boot.
S y s t e m R e s t a r t
← →
System re-start information.
I t w i l l r e s t a r t
Y e s ■ N o
Make confirmation, if you really want to re-boot

15
4.5 Entering parameter editing mode
When the system boot up and the hard disks are also in good condition, the LCD will display the
device name and IP (at the first time boot up, the IP will be the default IP). Shown as follows:
D C - 2 0 1 0
1 9 2 . 1 6 8 . 0 . 1 2 0
Now the device is waiting for manual input to configure from panel. With the touch wheel and
touch confirmation button, you can go through all the basic settings.
Touch the confirmation button more than 3 seconds to activate the setting message:
P W D : _ _ _ _ _ _
0 1 2 3 4 5 6 78 9 ← →↵↑
Input the password (default is 000000, 6 zeros), if you forget pass word, please keep
the confirmation button touched for more than 3 s to restore the default password.
P W D : * * * * * *
0 1 2 3 4 5 6 78 9 ← →↵↑
Select confirm to input data to DC2010
P a s s w o rd E r r o r
P l e a s e T r y A g a i n
If password error, try again.
If password correct, the system entering parameter editing mode.
Rotate the touch wheel, you can go through each page and select the desired page
by confirmation button to enter the mode.
S y s t e m S u m m a r y
← →
Display system information
L C D B a ck l i g h t
← →
Adjust and setting the LCD backlight
S c r e e n sa v e r t i m e
← →
Adjust the LCD screen saver time
N e t w o r k S e t t i n g
← →
Ethernet settings
U S B B a ck u p
← →
External USB backup

16
S e l e c t io n M e t h o d
← →
Touch wheel rotate or click mode
P a s s w o rd C h a n g e
← →
Change password of manual panel
C r e a t e S y s t e m
← →
New system generation or re-format the hard disk
R e s t o r e S e t t i n g
← →
restore system setting
R e t u r n M a i n
← →
Go back to top layer of menu
S y s t e m R e s t a r t
← →
DC2010 restart
A u t o D em o
← →
Demonstrate the setting procedures

17
4.6 System information from local panel
S y s t e m S u m m a r y
← →
Use touch wheel and confirmation to enter system parameter editing mode.
Touch the confirmation button to proceed with the information.
D e v i c e N a m e
D C 2 0 1 0
Display device name, default is DC2010 but you can modify to your preferred
through web API program. Touch confirmation button for next message.
F i r m w a re
V 1 . 0
Firmware version. Touch confirmation button for next message.
T o t a l C a p c i t y
9 2 8 G B y te
Total disk capacity (depends on the disk size).
Touch confirmation button for next message.
U s a g e
2 2 M B y t e( 1 % )
Display the disk usage. (depends on disk).
Touch confirmation button will jump to ‘System Summary’screen.

18
4.7 LCD backlight setting from local panel
Right shift the touch wheel until ‘Screensaver time’displayed.
L C D B a c kl i g h t
← →
Now you’re in LCD back light setting sub-function, touch confirmation button to
choose it. And the screen will enter ‘Time’setting.
B r i g h t ne s s
- ← 9 → +
Rotate the touch wheel to choose the normal backlight you want then touch the
confirmation button to return upper level.
4.8 Screensaver time setting from local panel
Right shift the touch wheel until ‘Screensaver time’displayed.
S c r e e n s av e r t i m e
← →
Now you’re in Screensaver time setting sub-function, touch confirmation button to
choose it. And the screen will enter ‘Time’setting.
T i m e : 0 60 s e c
0 1 2 3 4 5 67 8 9 ← → ↵↑
Enter time constant you want then rotate the touch wheel to choose confirm to
return upper level.

19
4.9 Network setting from local panel
In system parameter editing mode, right shift the touch wheel until ‘Network Setting’
displayed.
N e t w o r k S e t t i n g
← →
Now you’re in network setting sub-function, touch confirmation button to choose
it. And the screen will enter ‘Network Mode’setting.
N e t w o r k M o d e
D H C P ■S t a t i c ↑
If your device will be assigned IP by DHCP, choose it by rotate the touch wheel
to move the cursor on it then touch the confirmation button, the screen will
display ‘Network restart’for a while then return to ‘Network Setting’.
If you will assign static IP, move the cursor on it then touch the confirmation
button.
If your choice is static IP, the screen will display the previous setting.
D a t a C e n t e r I P
1 9 2 . 1 68 . 0 . 1 6 8
Touch the confirmation button to enter data entry mode.
1 9 2 . 16 8 . 0 0 0 . 0 0 7
0 1 2 3 45 6 7 8 9← → ↵↑
Use touch wheel and confirmation button to enter the data
1 9 2 . 16 8 . 0 0 0 . 0 0 7
0 1 2 3 45 6 7 8 9← → ↵↑
Select the confirm icon and touch the confirmation button to set DC2010
D a t a C e n t e r I P
1 9 2 . 1 68 . 0 . 7
Now return the upper level and new IP displayed, rotate touch wheel to next
item.
N e t m a sk
2 5 5 . 2 55 . 2 5 5 . 0
Touch confirmation button to enter data entry mode.
2 5 5 . 25 5 . 2 5 5 . 0 0 0
0 1 2 3 45 6 7 8 9← → ↵↑
Enter the net mask of your network and confirm to return upper level (net
mask display) then rotate touch wheel to ‘Gateway’display.
G a t e w ay
1 9 2 . 1 68 . 0 . 1