Jumpking JK48CO User manual

USER’S MANUAL . . . . . . . . . . . .3
Assembly, Installation, Care,
Maintenance, and Use Instructions.
Read the assembly, installation,
care,maintenance, and use
instructions in this manual prior
to assembling and using this
trampoline/enclosure.Save this
manual for future reference.
Recommended for use by children between 3~10 years of age.
Maximum weight limit: 100lbs(45kgs). Do not exceed the weight limit recommended
by the manufacturer.
Please read all of the direction prior to assembly. Do not apply excess force during
assembly. Assemble only with adult supervision. Use gloves to protect your hands
from pinch points and sharp points during assembly.
Warning! Not suitable for children under 36 months. Small parts and long cords may
be a choking and strangulation hazard.
YJ USA Corp.,
3970 Lindbergh Drive
Addison, TX 75001
Customer Hotline: [phone]
www.jumpking.com
Model: JK48CO / JK48CP / JK48SPT / JK48AP / JK48SBC / JK48SPC/
JK48BP / JK48FB
Warning
Warning
48in Mini Bouncer

CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
CARE AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
EXPLODED DRAWING AND PART LIST . . . . . . . . . . . . . . . . . . . 9
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . 9
2
QUESTIONS?
If you have questions after reading
this manual, please call our toll-free
Customer Hot Line. The trained
technicians on our Customer Hot Line
will provide immediate assistance.
Customer Hot Line:
1-877-927-8777
REPLACEMENT PARTS
www.jumpking.com
Model: JK48CO / JK48CP / JK48SPT /
JK48AP / JK48SBC / JK48SPC
JK48BP / JK48FB
48in Mini Bouncer

3
This product is intended for use by children between 3-10 years of age.
This enclosure is to be used only in connection with this trampoline.
Read and follow all warnings and instruction.
This product is intended to be assembled by an adult.
Maximum weight limited 45kg/100lbs.
Warning! Not suitable for children under 36 months. Small parts and long cords may be
a choking and strangulation hazard.
WARNING:

ASSEMBLY
IMPORTANT ASSEMBLY INFORMATION
A Phillips Head screw driver is needed to
assemble trampoline. However, a
screwdriver is not provided.
Assembly requires two persons. Keep
children away from the trampoline
until it is fully assembled.
Use gloves to protect your hands from pinch
points during assembly.
The assembly steps refer to parts by their descrip-
tions and key numbers (see the PART LIST on
page 9). If a part is missing, see ORDERING
REPLACEMENT PARTS on page 9 .
TRAMPOLINE PLACEMENT
1. Place the trampoline on a level surface
before use.
3. Use the trampoline in a well-lit
indoor or shady areas.
4. Secure the trampoline against
unauthorized and unsupervised use.
5. Remove any obstructions from beneath the
trampoline.
4
WARNING!
Please read all of the directions prior to assembly.
Inspect the trampoline to make sure all parts are included. If any worn, defective or
missing parts are found, please contact customer service immediately.
Make sure you wear gloves to protect your hands from pinch point and sharp point during installation.
Be careful where you place your hands; the springs and frame joints can pinch.
Check all screws for tightness and tighten up if loose.
Check all sharp edges and replace when required.
1.
2
4
Smaller end
T-connector+Welded tube
2.
1
1
33
3
3
44
1
1
2
2
T-connector
T-connector
T-connector
T-connector
T-connector+
Welded tube
1
3
10
10
Smaller end
T-connector

5
During the installation of springs, wear
gloves and protective eye wear (not provided).
11
5
Frame
3. Lay the Bed (6) on the ground inside of the
assembled frame. Make sure that the two warn-
ing decals (not shown) are on top of the Bed.
Note: There are V-rings around the edge of the
Bed (6) and holes around the top and bottom
of the frame.
During this step, you will attach the Bed to the frame
using the included Springs for holes on frame (see the
inset drawing). Hook a spring to the Bed (6) and using
the spring pulling tool (11), pull the spring from the Bed
to the hole slot in the trampoline frame with even spring
tension. Attach a second spring (5) directly across the bed
from the rst spring (5). Attach two more springs (5) halfway
between the rst two springs, so four spring (5) are attached
as shown. Attach four more springs (5) (not shown) halfway
between the rst four springs (5). Continue attaching springs
(5) halfway between the previously attached springs (5),
until all the springs (5) are attached.
3
3.5” Spring (5):
Hook the V-ring
Hook the top tube
V-ring
Spring holes on top of toprail
4. Lay the Frame Pad (7) on the frame. Adjust the position of
the Frame Pad so the notches are aligned with the
T-connector+welded tube as shown. Be sure the adjustable
handle frame openings are t to the T-connector+welded
tube position.
Do not use the trampoline without the Frame
Pad (7), which is designed to reduce the likeli-
hood of injury to the user from coming in con-
tact with the trampoline frame. If you do not
have a Frame Pad, contact your dealer to
obtain one. Properly install the Frame Pad
before using the trampoline.
4
Notch
T-connector+welded
and straight(4)
7

6
5. Look under the trampoline and locate the pairs of
straps attached to the underside of the Frame Pad
(7). Note that some pairs of straps are near the
frame and other pairs of straps are near the edge
of the Bed (6). Position each outer pair of straps
so one strap is on each side of the frame as
shown. Position each inner pair of straps so one
strap is on each side of the nearest Spring (5) as
shown.
See the inset drawing.
Do not overtighten the straps.
Repeat this step with the remaining straps (not
shown).
5
Strap with “S” hook on the pad edge
Cross the strap over the toprail frame to hook the V ring
6. Thread one end of Elastic Tie-Down, then tie a knot
on V-Ring.
Repeat this step with the remaining straps which at
middle position of each pad section (not shown).
7
Elastic Tie-Down
6
7
Elastic Tie-Down
Spring
V-Ring
V-Ring
5
T-connector+welded
tube
Frame pad (7)
Adjustable handle frame opening
6
7. Lay two bottom poles (8), and one arch pole (9)
on the ground.
Insert the foam sleeve cover(14) into bottom poles(8)
and arch pole(9) to protect the foam.
Make sure that the bottom pole (8) is oriented
so the small holes are in the position shown.
Slide a Foam Sleeve (13) onto each of the tubes;
note that the ends of the bottom pole (8) should
not be covered.
Connect the bottom pole (8) to arch pole (9) by the clip.
Joint the end of each pole by Clip of Connector
8
8
14 13
9
9
89

7
9
9.
Disassembly
8.
8
8.
9
10
10
The trampoline is now fully assembled. Make
sure that all parts are securely attached. Familiarize
yourself and all users of the trampoline with the
safety precautions,use and instructional materials,
and care and maintenance instructions in this
manual before using the trampoline.
To disassemble the trampoline, follow assembly steps 1 through 9 in reverse order. Do not attempt to
disassemble any trampoline frame components before the springs and bed have been removed. Use gloves to
protect your hands from pinch points during disassembly.
Insert the handle (8 / 9) into T-connector +Welded tube.
Tighten the self-tapping screw (10).
When doing so, please ensure that the arch
pole faces inward.

8
CARE AND MAINTENANCE
Care
Do not allow pets or animals on the trampoline
as claws may snag and pull the bed material or
damage the frame pad
The trampoline is intended to be used by
one person at a time weighing 45kg(100lbs) or less.
The user should be either barefoot or wearing socks.
Street shoes or tennis shoes should not be worn on
the trampoline. The user should remove all sharp
objects from his or her person that may cause injury
or damage to the bed. Heavy, sharp, or pointed hard
objects should not contact the bed.
Maintenance
Your trampoline is manufactured using quality materi-
als and crafted to provide your children with many
years of enjoyment. Proper maintenance and care will
help to prolong the life of the trampoline and reduce
the possibility of injury.
Prolonged exposure to the sun, will shorthen the life
of the trampoline fabric. For longer fabric life store
the trampoline when it is not being used.
A dry trampoline, properly stored, will
provide the longest life of the fabric, sewing, and
hardware. Remove the enclosure from the trampoline
during harsh weather conditions or during long
periods of non-use.
The following guidelines should always be observed.
Inspect the trampoline before each use,
and replace any worn, damaged, or missing parts.
The following conditions could represent potention
hazards and increase the chance of personal injury:
- a missing, improperly positioned, or insecurely
attached frame pad, foam sleeves.
- punctures, frays, tears, or holes worn in the bed, frame
pad, foam sleeves.
- deterioration in the stitching or fabric of the bed, frame
pad.
- broken or missing springs.
- a bent or broken frame, leg.
- a sagging bed.
- sharp protrusions on the frame, suspension system.
If any of these conditions exist, the trampoline should be
dissembled or otherwise protected against use until the
condition is corrected.
Removing and storing the trampoline
Make sure that the trampoline is dry before
removing and storing it. Use caution while removing the
tubes due the weight of the tubes.
Once the enclosure is removed from the trampoline.
remove all items from the trampoline bed. Make sure that
the bed is clean and that it has no tears or holes. Store
the trampoline in a safe, dry location.
Moving the trampoline
If the trampoline needs to be moved, it should
be moved by two persons, kept horizontal, and lifted
slightly. If necessary, the trampoline can be
disassembled for moving.
To disassemble the trampoline, follow the
assembly steps in reverse order (see pages 4 to 7). Do
not attempt to disassemble the frame sections, legs or
bases before the bed and springs have been removed.

9
*This part is not illustrated.
are subject to change without notice.
EXPLODED DRAWING AND PART LIST
ORDERING REPLACEMENT PARTS
•
•
•
•
•
Key
No. Qty. Description
Ke y
No. Qty. Description
1 4 Top Tube with T-connector
2 2 Top Tube with T-connector+welded tube
3 4
5 30 3.5” Length Springs
6 1 Stitched Bed with V-rings
7 1 Frame Pad with Frog printing
8 2 Bottom pole
Straight leg
4 2 Straight leg with welded tube
9 1 Arch pole
10 8 Self-tapping screw
11 1 Spring Pulling Tool
12 1 User’s Manual
*13 3 Foam sleeves (had been attached to
adjustable handle)
14 1 Set of foam sleeve cover
13
14
12
11
1
2
3
4
5
67
8
10
9
To order replacement parts, visit our Web site or call our Customer Hotline (see page 2). To help us assist you,
please provide the following information when calling:
the MODEL of the trampoline
the NAME of the product
the KEY NUMBER and DESCRIPTION of the part (see the PART LIST above)
the quantity needed
the desired method of shipping