Jumpking ACC-UBSKU-BOLT User manual

Please contact us at
[email protected]
- Please read all instructions prior to assembly.
- Adult supervision is required during assembly.
- Assembly requires 2 people.
- Use gloves during assembly to protect hands from pinch points and sharp edges.
- Check for any loose nuts and bolts, then tighten if necessary.
- Check all caps and coverings for defects or deterioration. Replace if necessary.
- Inspect the basketball hoop before each use and replace any worn, defective or missing parts.
- This basketball hoop is not suitable for assembly on an enclosure pole with a tunnel sleeve.
- For proper t and grip during assembly, the enclosure pole should be covered with a foam sleeve.
Model: ACC-UBSKU-BOLT

COMPATIBLE MODELS
Bent Pole
Outside Curved
Pole
Straight Pole
Curved Pole
Inside Straight
+ Curved Pole

Description:
Screw and nut set
for Basketball back
board (preassembled
to Part A)
Description: Description:
Basketball Board
and Hoop
Inflatable ball
Quantity:
1
Quantity:
1
Part List
Part A Part B
Description:
Inflator and plastic
needle
Quantity:
1
Part C
Description:
7 Shape tube
Quantity:
1
Part D
Description:
Middle tube
Quantity:
1
Part E
Description:
Bottom tube
Quantity:
1
Quantity:
4 sets
Description:
Screw, nut and washer
set for Basketball back
board
Quantity:
1 set
Description:
Self Tapping Screw
Quantity:
2 pcs
Part F Part G Part H
Part I
Description:
Wedge
Quantity:
1 pcs
Description:
U-bolt
Quantity:
2 pcs
Description:
Lock Nut
Quantity:
4 pcs
Part J Part K Part L
Description:
U-Bolt Bracket
Quantity:
2 pcs
Part M
Description:
Plastic Nut Cap
Quantity:
4 pcs
Part N
ACC-UBN/BBHN ACC-BSKB14 ACC-APN ACC-UBU/CP
ACC-UBU/MP
HWSTS HWWEDGE HWUBOLT HWUBOLT
HWUBOLT HWUBOLT
ACC-UBU/BP ACC-UBU/SBBS4 ACC-UBU/SBP

How to assemble basketball hoop onto enclosure pole
Part D
Part D
Part H
Part E
Part F
Part I
Part J
Part J
Part K
Part K
Part L
Part L
Part M
Part M
Part N
Part N
Part H
You will need the following parts to complete this step:
1 x 7 Shape tube- Part D
1 x Middle tube - Part E
1 x Bottom tube - Part F
2 x Self Tapping Screw – Part I
Insert one end of the middle tube into the 7 shape tube
and the other end into the bottom tube.
Align the holes of all 3 tubes.
Screw one of the self-tapping screws through the hole
connecting the 7 shape tube to the middle tube and the
other screw through the hole connecting the middle tube
to the bottom tube using a Philips-head screwdriver (not
included).
You will need the following parts to
complete this step:
1 x Basketball Board and Hoop - Part
A
Parts D, E & F (assembled in previous
step)
4 x Screw and nut set for Basketball
back board - Part G (preassembled to
Part A)
1 x Screw, nut and washer set for
Basketball back board - Part H
Insert 7 Shape tube end into back of Basketball Board. Align
the holes and insert the screw, washer and nut and secure in
place with Philips-head screwdriver & socket wrench (not
included).
You will need the following parts to
complete this step:
1 x Wedge - Part J
2 x U-bolt - Part K
4 x Lock Nut - Part L
2 x U-Bolt Bracket – Part M
4 x Plastic Nut Cap – Part N
Align the basketball hoop onto one
of the trampoline enclosure poles.
Make sure the position of the
basketball hoop is facing inward.
Start attaching the U-bolts followed
by the wedges, U-bolt brackets and
lock nuts. Tighten with socket
wrench (not included). Then place
plastic nut caps over lock nuts.
Part A