Jumpking JK7524TBG User manual

USER’S MANUAL . . . . . . . . . . . .3
Assembly, Installation, Care,
Maintenance, and Use Instructions.
Recommended for use by children above 3 years of age.
Maximum weight limit: 180lbs(82kgs). Do not exceed the weight limit recommended
by the manufacturer.
Read the assembly, installation,
care,maintenance, and use
instructions in this manual prior
to assembling and using this
trampoline/enclosure.Save this
manual for future reference.
88INCH / 2.24M
7.5FT HEXAGONAL COMBO
TRAMPOLINE AND ENCLOSURE
WITH TOSS BALL GAME
Please read all of the direction prior to assembly. Do not apply excess force during
assembly. Assemble only with adult supervision. Use gloves to protect your hands
from pinch points and sharp points during assembly.
Warning! Not suitable for children under 36 months. Small parts and long cords may
be a choking and strangulation hazard.
YJ USA Corp.,
3970 Lindbergh Drive
Addison, TX 75001
Customer Hotline: [phone]
www.jumppod.com
www.jumpking.com
Model: JK7524TBG
Warning
Warning

２

Model: JK7524TBG
4
5
11
12
12
7.5FT HEXAGONAL COMBO
TRAMPOLINE AND ENCLOSURE
WITH TOSS BALL GAME

This product is intended for use by children above 3 years of age.
This enclosure is to be used only in connection with this trampoline.
Read and follow all warnings and instruction.
This product is intended to be assembled by an adult.
Maximum weight limited 82kg/180lbs.
Warning! Not suitable for children under 36 months. Small parts and long cords may be
a choking and strangulation hazard.
WARNING:

ASSEMBLY
IMPORTANT ASSEMBLY INFORMATION
A Phillips Head screw driver is needed to
assemble trampoline/enclosure. However, a
screwdriver is not provided.
Assembly requires two persons. Keep
children away from the trampoline/enclosure
until it is fully assembled.
Use gloves to protect your hands from pinch
points during assembly.
The assembly steps refer to parts by their descrip-
tions and key numbers (see the PART LIST on
page 11). If a part is missing, see ORDERING
REPLACEMENT PARTS on page 11.
TRAMPOLINE/ENCLOSURE PLACEMENT
1. Place the trampoline/enclosure on a level surface
before use.
3. Use the trampoline/enclosure in a well-lit
indoor or shady areas.
4. Secure the trampoline/enclosure against
unauthorized and unsupervised use.
5. Remove any obstructions from beneath the
trampoline/enclosure.
6. The trampoline enclosure is only to be used
as an enclosure for a hexagonal trampoline.
1.
1a.
1b.
1a.
1b.
You have now assembled one leg sections. Repeat the step
to assembled remaining sections.
WARNING!
Please read all of the directions prior to assembly.
Inspect the trampoline and enclosure to make sure all parts are included. If any worn, defective or
missing parts are found, please contact customer service immediately.
Make sure you wear gloves to protect your hands from pinch point and sharp point during installation.
Be careful where you place your hands; the springs and frame joints can pinch.
Check all screws for tightness and tighten up if loose.
Check all sharp edges and replace when required.
1
1
1
1
1
1
2
2
2
2
2
2
33
3
3
3
3
1
1
2
2
7 7
17 17
33
88
Make sure you understand the information in the box at the top of this
page before you begin assembling the trampoline.
Lay two top tubes (1) on the ground as shown. There have over and
under spring holes on top tubes(1). The 2 spring holes are facing on top.
Make sure there is a POD-connector(2) on each Top tube.
Insert the top tube into the POD-connector as picture 1a shown.
Insert the leg(3) with leg foam sleeve(7) into POD-connector(2),
tighten a Self-tapping screw(17) into small hole in the POD-connector(2).
Then cover the plastic foot pad(8) into leg(3).
Bottom spring holes
Top spring holes Top spring holes

2. Note: This step requires two people.
During this step, you will connect the six leg sec-
tions.
Hold the leg sections in the positions shown.
Insert the top tube into the POD-connector.
Repeat this step until all six leg sections are
connected.
3. Lay the Bed (5) on the ground inside of the
assembled frame.
Note: There are V-rings around the edge of the
Bed (5) and holes around the top of the frame.
During this step, you will attach the Bed to the
frame using the included Springs for holes
on frame (see the inset drawing). Hook a spring to
the Bed(5) and using the spring pulling tool(18),
pull the spring from the Bed to the hole slot in the
trampoline frame with even spring tension.
Attach the springs(4) in the order shown in the
diagram 3. This will help to distribute the tension,
making assembly easier.
Once all of the springs shown in the diagram have
3
5” Spring (4):
During the installation of springs, wear
gloves and protective eye wear (not provided).
1
1
1
1
1
1
22
2
2
2
2
2
3
3
3
3
3
3
1
2
3
4
5
6
7
8
9
10
11
12
Bed(5)
POD-Connector
Spring
18
4
Webbing loop
Frame

4. Lay the Frame Pad (6) on the frame. Adjust the
position of the Frame Pad so the notches are
aligned with the Legs (3) as shown. Be sure
6 Enclosure Frame Openings are fitted to the
POD-connector position.
Do not use the trampoline without the Frame
Pad (6), which is designed to reduce the likeli-
hood of injury to the user from coming in con-
tact with the trampoline frame. If you do not
have a Frame Pad, contact your dealer to
obtain one. Properly install the Frame Pad
before using the trampoline.
4
POD-connector
Frame pad (6)
Enclosure frame opening
The trampoline is now fully assembled. Make
sure that all parts are securely attached.
Familiarize yourself and all users of the tram-
poline with the safety precautions, use and
instructional materials, and care and mainte-
nance instructions in this manual before using
the trampoline.
5
5.

You will now assemble the Safety Enclosure
for your trampoline.
6.
7.
Take the Enclosure Bottom curve poles(9),
Enclosure Top curve poles(10),
Enclosure Bottom straight poles(11),
Enclosure Middle straight poles(12), and
Enclosure Top bent poles(13).
Find the tapered end of the Enclosure poles
and insert it into the Enclosure Middle and Top
poles as per drawing.
Repeat this with the remaining Enclosure poles
so you have 6 identical Enclosure poles assembled.
You will require a screwdriver (not included) to complete assembly. Do not allow use of the
trampoline during assembly.
Take a completed Enclosure poles Assembled and
insert into POD-connector(2) as shown in the picture.
Rotate the Enclosure poles so the screw
holes align.
Then screw the Tubes together using a self
tapping screw (17).
2
9
10
9
10
11
11
12
13
12
13
4 sets Enclosure
poles 9, 10.
2 sets
Enclosure
poles 11,
12, 13.

8. Spread the Netting (15) on the trampoline bed.
8
9
9
Find the ROD on top of enclosure netting. Rod
Stand on the trampoline and insert one of the
exposed sections of the Black G4 pole into a
plastic grip on top of one of the enclosure tubes.
Attach the others exposed sections of the
RODs to the other enclosure tubes in the
order shown in the diagram.
completed step 9.

The trampoline / enclosure is now fully assembled.
Make sure that all parts are securely attached. Fimiliar-
ize yourself and all users of the trampoline/enclosure
with the safety precautions, use and instructional
materials, and care and maintenance instructions in this
manual before using.
12.
Disassembly
To disassemble the trampoline enclosure, follow assembly steps 1 through 11 in reverse order. Do not attempt to
disassembly any trampoline frame components before the springs and bed have been removed. Use gloves to
protect your hands from pinch points during disassembly.
10.
12.
11.
15
10
19
14
12
10
Webbing loop
Door
Webbing loop
V-Ring
Cord
11
Note: During steps 10 and 11, you will “sew” the
lower edge of the netting(15) to the V-ring and
webbing loop on the bed using the cords(19).
Locate the V-ring closest to the door. Thread one
end of a cord(19) through the lower edge of the
netting(15) above the V-ring and then thread the
cord through the V-ring. Tie the netting to the V-ring,
by making a double knot in the cord.
Thread the cord(19) through the lower edge of the
netting(15) to the V-ring and webbing loop. Repeat
this procedure until the entire cord is threaded
through the netting, V-rings and webbing loops as
shown.
Keep the cord tight. Tie the end of the cord to the
last V-ring that it reaches.
Tie a second cord(not shown) to the last V-ring
reached by the first cord. Thread the second cord
through the netting(15), V-rings and webbing loops
as described above. Repeat this procedure with the
remaining cord until the last cord reaches the first
cord. (Note: The last cord may overlap the first
cord.) Make sure that the netting is sewn to every
V-ring and webbing loop on the trampoline bed;
the netting below the door must also be sewn to
the V-rings.

CARE AND MAINTENANCE
Care
Do not allow pets or animals on the trampoline or
inside the enclosure, as claws may snag and pull the
bed material or damage the frame pad or netting.
The trampoline/enclosure is intended to be used by
one person at a time weighing 82kg(180lbs) or less.
The user should be either barefoot or wearing socks.
Street shoes or tennis shoes should not be worn on
the trampoline. The user should remove all sharp
objects from his or her person that may cause injury
or damage to the bed. Heavy, sharp, or pointed hard
objects should not contact the bed.
Maintenance
Your trampoline is manufactured using quality materi-
als and crafted to provide your children with many
years of enjoyment. Proper maintenance and care will
help to prolong the life of the trampoline and reduce
the possibility of injury.
Prolonged exposure to the sun, will shorthen the life
of the trampoline/enclosure fabric. For longer fabric
life store the trampoline/enclosure when it is not being
used. A dry trampoline/enclosure, properly stored, will
provide the longest life of the fabric, sewing, and
hardware. Remove the enclosure from the trampoline
during harsh weather conditions or during long
periods of non-use.
The following guidelines should always be observed.
Inspect the trampoline/enclosure before each use,
and replace any worn, damaged, or missing parts.
The following conditions could represent potention
hazards and increase the chance of personal injury:
- a missing, improperly positioned, or insecurely
attached frame pad, netting, enclosure tubes, foam
sleeves.
- punctures, frays, tears, or holes worn in the bed, frame
pad, netting, foam sleeves.
- deterioration in the stitching or fabric of the bed, frame
pad, netting.
- broken or missing springs.
- a bent or broken frame, leg, enclosure poles.
- a sagging bed or netting.
- sharp protrusions on the frame, suspension system,
enclosure tubes.
If any of these conditions exist, the trampoline should be
dissembled or otherwise protected against use until the
condition is corrected.
Removing and storing the trampoline/enclosure
Make sure that the trampoline/enclosure is dry before
removing and storing it. Use caution while removing the
tubes due the weight of the tubes.
Once the enclosure is removed from the trampoline.
remove all items from the trampoline bed. Make sure that
the bed is clean and that it has no tears or holes. Store
the trampoline/enclosure in a safe, dry location.
Moving the trampoline
If the trampoline/enclosure needs to be moved, it should
be moved by two persons, kept horizontal, and lifted
slightly. If necessary, the trampoline/enclosure can be
disassembled for moving.
To disassemble the trampoline/enclosure, follow the
assembly steps in reverse order (see pages 4 to 9). Do
not attempt to disassemble the frame sections, legs or
bases before the bed and springs have been removed.

EXPLODED DRAWING AND PART LIST
ORDERING REPLACEMENT PARTS
To order replacement parts, visit our Web site or call our Customer Hot Line (see page 3). To help us assist you,
please provide the followinginformation when calling:
the MODEL of the trampoline/enclosure
the NAME of the product
the KEY NUMBER and DESCRIPTION of the part (see the PART LIST above)
the quantity needed
the desired method of shipping
*This part is not illustrated.
Key
No.Qty. Description
Key
No. Qty. Description
1 6 Top Tube with POD-connector
2 6 POD-connector
3 6 Straight leg
4 36 5” Length Springs
5 1 Stitched Bed with V-rings
6 1 Frame Pad
7 6 Leg foam sleeve
8 6 Plastic foot pad
9 4 Enclosure Bottom curve poles
10 4 Enclosure Top curve poles
11 4 Enclosure Bottom straight poles
14 12 Enclosure Foam Sleeves
12 2 Enclosure Middle straight poles
13 2 Enclosure Top bent pole
15 1 Netting with attached Hardware
16 1 User’s Manual
17* 14 Self-tapping Screw (2 pcs for spare use)
18 1 Spring Pulling Tool
19* 4 Cord
20 6 Plastic Cap(have been attached to
21 1 Ball
the Enclosure top curve & bent pole
10 & 13)
16
4
14
7
18
8
3
7
3
6
1
2
USER’S MANUAL . . . . . . . . . . . .3
Assembly,Installation, Care,
Maintenance, and Use Instructions.
Recommendedfor use by children above 3 years of age.
Maximumweight limit: 180lbs(45kgs). Do not exceed the weight limit recommended
bythe manufacturer.
Readtheassembl y,installation,
care,maintenance,anduse
instructionsin this manual prior
toassemblingand using this
trampoline/enclosure.Savethis
manualfor future reference.
88INCH / 2.24M
7.5FT HEXAGONAL KIDS COMBO
TRAMPOLINE AND ENCLOSURE
Pleaseread all of the direction prior to assembly. Do not apply excess force during
assembly.Assemble only with adult supervision. Use gloves to protect your hands
frompinch points and sharp points during assembly.
Warning!Not suitable for children under 36 months. Small parts and long cords may
bea choking and strangulation hazard.
YJUSACorp.,
3970Lindbergh Drive
Addison,TX 75001
CustomerHotline: 1-877-927-8777
www.jumppod.com
www.jumpking.com
Model: JK7525TBG
Warning
Warning
5
9
12
13 10
15
11
21
20