JumpPro Xcite User manual

8ft, 10ft, 12ft and 14ft JumpPRO Xcite Round
Trampoline with Enclosure
WARNING! Read these Assembly Instructions before assembling and
using your trampoline. Max User weight Limit
8ft: 50kg, 10ft: 120kg, 12ft,14ft: 150kg
JumpPRO Xcite Assembly Instructions
Warning! Not suitable for children under
36 months - small parts, choking hazard!

Max User Weight:
Recommended age 6+ years.
Only for domestic use.
The trampoline is intended for outdoor use only.
The trampoline shall be assembled by an adult in accordance with the assembly instructions and
thereafter checked before the first use.
Adult supervision and guidance is required at all times during use.
Only one user at a time. Collision hazard.
Always close the net opening before jumping.
Jump without shoes.
To prevent accidents due to slipping, do not use the trampoline when the mat is wet.
Empty your pockets and hands before jumping.
Always jump in the middle of the jump mat.
Do not eat while jumping.
Do not exit by a jump.
Do not perform somersaults! Somersaults increase the risk of landing on your head or neck which
may result in serious injuries or even death. Limit the time of continuous usage (make regular
stops).
Do not use in strong wind conditions and secure the trampoline.
WARNINGS!
8ft: 50kg, 10ft: 120kg, 12ft: 150kg, 14ft: 150kg
1

The trampoline is not intended to be buried into the ground.
Product dimensions:
All users should be aware of their own limitations.
The risk of severe injury must by taken seriously.
It is important to bend your knees on landing to achieve the best possible control. Jump up and in
the same spot -this provides the best control.
Aim for the middle marking.
Gain full control of your jumps before attempting more difficult jumps.
Moving the trampoline: If the trampoline and enclosure needs to be moved, it should be moved by
a minimum of two persons, kept horizontal and lifted slightly.
If necessary, the trampoline and enclosure can be taken apart for moving. To take the
trampoline apart, follow the assembly steps in reverse order.
It is recommended to place the trampoline on a flat and level surface at least 2 m from any
structure or obstruction such as a fence, garage, house overhanging branches, laundry lines or
electrical wires.
Trampolines shall neither be installed over concrete, asphalt or any other hard surface nor at
proximity of other conflicting installations (e.g. paddling pools, swings, slides, climbing frames).
Modifications made by the consumer to the original trampoline (e.g. the adding of an accessory)
shall be carried out according to the instructions of the manufacturer.
INFORMATION
8ft: 244x244x231CM
10ft: 305x305x245CM
12ft: 366x366x265CM
14ft: 427x427x269CM
2

Please pay attention to the need to carry out checks and maintenance of the main parts
Check all nuts and bolts for tightness and tighten when required.
Check that all spring-loaded (pit pin) joints are still intact and cannot become dislodged during play.
Check all coverings and sharp edges and replace when required.
Retain the maintenance instruction manual.
Outdoor trampolines should be equipped with a device that in strong wind conditions avoid
displacement due to wind (e.g. steel bars in the ground or loads like sand bag or water bags) and/or
items catching wind like net and mat should be removed.
In certain countries during winter period, the snow load and the very low temperature can damage
the trampoline. It is recommended to remove the snow and store the mat and the enclosure indoor.
Check that the mat, padding and enclosure are without defects.
NOTE: Sunlight, rain, snow and extreme temperatures reduce the strength of these parts over time
Inspect the trampoline and the netting for defects before use every time. Tighten up fittings and
check regularly that all ties have been tied correctly. Replace the net after 1 year of use.
Make sure that the hook-and-loop fasteners are closed correctly during use of trampoline
Trampoline and net should be packed away in winter. Make sure all parts are dry and
packed securely. Store dry. Always be aware of wear and tear due to weather and wind.
We recommend securing the trampoline in strong winds. Tie the trampoline down with ropes
attached to the trampoline top rail. Tie the trampoline down in a minimum of three places distributed
evenly across the trampoline frame.
Do not secure the legs as these may become misaligned and damage the trampoline. Dismantle or
remove the trampoline completely, if required. It may result in great danger if the trampoline is not
secured in strong winds.
ASSEMBLY AND MAINTENANCE INSTRUCTIONS
(frame, suspension system, mat, padding and enclosure) at the beginning of each season and also
at regular intervals. If these checks are not carried out, the trampoline could become dangerous.
3

JUMPING INSTRUCTIONS
Fundamental Bounce
1. Start from a standing position with your head
erect and your eyes on the frame pad.
2. Swing your arms forward and up in a circular
motion.
3. Bring your feet together and point your toes
downward while in the air.
4. Keep your feet about 30 cm (15 in.) apart when
landing on the bed.
Knee Drop
1. Start bouncing from a standing position, keeping
your eyes on the frame pad.
2. Land on your knees, keeping your back straight
and your body erect.
3. Bounce back to an erect position.
Seat Drop
1. Land in a sitting position with your legs parallel to
the bed.
2. Place your hands on the bed beside your hips.
3. Push with your hands to return to an erect
position.
Front Drop
1. Start from a low bounce and land on the bed in a
prone position.
2. Keep your head up and your arms extended
forward on the bed.
3. Push with your arms to return to an erect position.
A certified trampoline instructor should be contacted to further develop your
trampoline skills.
4

ASSEMBLY INSTRUCTIONS
To assemble this trampoline we have provided you with our special spring loading tool
(item H), a cross head screwdriver (item J) and spanners (items I). During periods of non-
use, this trampoline can be easily disassembled and stored.
Please read the assembly instructions before beginning to assemble the product.
PRIOR TO ASSEMBLING
Please refer to page 6-7 for part descriptions and numbers. The assembly steps use these
description and numbers as reference for your convenience.
Make sure that you have all parts listed. If you are missing any parts, please refer to page
18 for Instructions on how to obtain any parts.
WHAT YOU WILL NEED FOR BUILDING YOUR TRAMPOLINE
Safety glasses Mallet
To help build your trampoline, you will need gloves, safety glasses and a mallet.
Please note that these are not supplied with your trampoline.
5
Gloves

TRAMPOLINE PART LIST
6

7

8
Lay out all the trampoline parts in groups, as shown in the picture. 1.
STEP 1: TRAMPOLINE PARTS
STEP 2: ASSEMBLING THE FRAME
2. Attach the leg extensions (E) to the leg base (F) securely. Making sure that the holes in the leg
extensions are aligned with the holes in the leg base.
Note: The 8ft model does not come with or require leg extensions.
Note: Product images are for illustration purposes only, component part colours may vary
dependent on which JumpPRO model you have purchased.

3. Connect the top rails (C) with the T-connectors (G)
as shown in the picture above. Continue until you
form a large circle.
Note: The images below are for the 8ft and 10ft
models. 12ft and 14ft versions have 8 top rails,
8 T connectors and 4 legs.
9
4.Two people are needed to assemble the trampoline. Lift the circular frame and install the
assembled legs.

ab
10
STEP 3: ATTACHING THE BED
WARNING:
Be careful where you place your hands during spring assembly as connector points can
pinch!
Note: It is easier to place one hand on the frame and pull the spring towards you, as shown above.
Make sure that "a" is attached to the D-rings of the jumping mat and "b" is attached to the
trampoline frame.
IMPORTANT: Springs must be attached the right way around and fully inserted into the holes
along the top of the frame.

11
5. Slot one of the springs (D) onto one of the D-
rings of the jumping mat (B). Slot the other end of
the spring into one of the spring holes along the top
rail. Start by attaching the springs to the left sides of
each T-connector (G) using spring pulling tool (H).
The First Spring Hole
T-connector(G)
Note: To ensure that you have started to fit the bed correctly, please count the spring
holes in between each T connector to make sure that you have the same number of
spring holes in the top rails.

①
②
6. Each time you connect a spring to the jumping mat, make sure you attach another spring to the
opposite side to allow better tension and pressure. Repeat this until all the springs are attached.
Note:
1) Make sure that the D-rings on the bed, match the number of holes along the top rails.
2) If you notice that you have skipped a hole and D-ring connection, recount, remove and adjust
accordingly.
12
1
6
4
3
2
5
7
8
9
10
11
12

7. Lay the frame pad (A) over the trampoline so that the springs and the steel frame are covered.
Please ensure that the frame pad covers all metal parts.
8. Tie the straps located underneath the frame pad to the frame. Do not tie them to the springs.
13
STEP 4: FITTING THE FRAME PAD
WARNING: The trampoline MUST NOT be used during construction.
STEP 5: ASSEMBLING THE ENCLOSURE POLES

14
9. Insert the fork screws (P) through the bottom enclosure poles (M). Use the plastic spacer (supplied
with the fork screws) in between the bottom enclosure poles (M) and the leg extensions (E) Tighten
the nuts of each fork screw with the bolts and spanner provided (I).
DO NOT OVER TIGHTEN!
10. Screw the screw caps
(Q) onto the back of each
nut for protection.

11. Insert the top enclosure poles (N) into the bottom enclosure poles (M) using the screws (O) and
screwdriver provided (J) as shown in the above images.
15
12. Slide the fiberglass rods (S) into the passage sewn at the top of the enclosure net (K). Repeat
this until all the fiberglass rods are fully inserted with T plastic caps (R). One person will be required
to thread the fiberglass rods through the passage at the top of the net, another person will be
required to gradually bend the rods around the passage to form a circle.
Passage sewn on the top of
enclosure net
Fiberglass Rod (S)
T Plastic Cap (R)
STEP 6: ATTACHING THE FIBERGLASS RODS AND T
PLASTIC CAPS TO THE NET

13. Attach the fiberglass rods with the safety net to the top of the enclosure poles (N) by inserting the
T Plastic Caps (R) into the top of the enclosure poles.
16
Door
Enclosure Net
D-rings on Jumping Mat
Cord (L)
14. Locate the D-ring closest to the door of the net. Thread one end of one of the cords (L) through
the lower eyelet of the enclosure net (K) above the D-ring and then thread the cord through the D-
ring. Tie the enclosure net to the D-ring, by making a double knot in the cord.

Cord (L)
Enclosure Net
Door
D-rings on Jumping Mat
17
15. Thread the cord (L) through the lower eyelet of the enclosure net (K) halfway between the first D-
ring and the D-ring to the left, and then thread the cord through to the left. Repeat this procedure
until all the cords are threaded through the enclosure net and the D-rings as shown. Keep the cords
taut.
16. Tie each end of the cord sections to the last D-ring that it reaches. Make sure that the enclosure
net is attached to every D-ring on the trampoline bed.

To order replacement parts, please contact our Customer Service team:
In order to help assist you, please have the following information to hand:
Product description, Item ID and item description (refer to pages 6-7 to obtain this information)
18
17. The trampoline and enclosure are now fully assembled. Make sure that all parts are securely
attached. Familiarise yourself and all users of the trampoline and enclosure with the safety
precautions, use and instructional materials, and care and maintenance instructions in this manual
before using.
SPARE PARTS