JumpPro Xcite User manual

JumpPRO™ Xcite Assembly Instructions
9ft x 6ft, 10ft x 7ft and 12ft x 8ft JumpPRO™ Xcite Rectangular
Trampoline with Enclosure
WARNING! Read these Assembly Instructions before assembling and
using your trampoline. Max User weight Limit 150kg
Warning! Not suitable for children under
36 months - small parts, choking hazard!

Max User Weight: 150kg
Recommended age 6+ years.
Only for domestic use.
The trampoline is intended for outdoor use only.
The trampoline shall be assembled by an adult in accordance with the assembly instructions and
thereafter checked before the first use.
Adult supervision and guidance is required at all times during use.
Only one user at a time. Collision hazard.
Always close the net opening before jumping.
Jump without shoes.
To prevent accidents due to slipping, do not use the trampoline when the mat is wet.
Empty your pockets and hands before jumping.
Always jump in the middle of the jump mat.
Do not eat while jumping.
Do not exit by a jump.
Do not perform somersaults! Somersaults increase the risk of landing on your head or neck which
may result in serious injuries or even death. Limit the time of continuous usage (make regular
stops).
Do not use in strong wind conditions and secure the trampoline.
WARNINGS!
1

The trampoline is not intended to be buried into the ground.
Product dimensions:
All users should be aware of their own limitations.
The risk of severe injury must by taken seriously.
It is important to bend your knees on landing to achieve the best possible control. Jump up and in
the same spot - this provides the best control.
Aim for the middle marking.
Gain full control of your jumps before attempting more difficult jumps.
It is recommended to place the trampoline on a flat and level surface at least 2 m from any
structure or obstruction such as a fence, garage, house overhanging branches, laundry lines or
electrical wires.
Trampolines shall neither be installed over concrete, asphalt or any other hard surface nor at
proximity of other conflicting installations (e.g. paddling pools, swings, slides, climbing frames).
Modifications made by the consumer to the original trampoline (e.g. the adding of an accessory)
shall be carried out according to the instructions of the manufacturer.
If the trampoline and enclosure needs to be moved, it should be moved by a minimum of
two people, kept horizontal and lifted slightly.
If necessary, the trampoline and enclosure can be taken apart for moving. To take the
trampoline apart, follow the assembly steps in reverse order.
INFORMATION
9ft x 6ft: 275x183x245CM
10ft x 7ft: 305x214x256CM
12ft x 8ft: 366x244x265CM
MOVING THE TRAMPOLINE
2

Please pay attention to the need to carry out checks and maintenance of the main parts
Check all nuts and bolts for tightness and tighten when required.
Check that all spring-loaded (pit pin) joints are still intact and cannot become dislodged during
play.
Check all coverings and sharp edges and replace when required.
Retain the maintenance instruction manual.
Outdoor trampolines should be equipped with a device that in strong wind conditions avoid
displacement due to wind (e.g. steel bars in the ground or loads like sand bag or water bags) and/or
items catching wind like net and mat should be removed.
In certain countries during winter period, the snow load and the very low temperature can damage
the trampoline. It is recommended to remove the snow and store the mat and the enclosure indoor.
Check that the mat, padding and enclosure are without defects.
NOTE: Sunlight, rain, snow and extreme temperatures reduce the strength of these parts over time.
Inspect the trampoline and the netting for defects before use every time. Tighten up fittings and
check regularly that all ties have been tied correctly. Replace the net after 1 years of use.
Make sure that the hook-and-loop fasteners are closed correctly during use of trampoline.
Trampoline and net should be packed away in winter. Make sure all parts are dry and
packed securely. Store dry. Always be aware of wear and tear due to weather and wind.
We recommend securing the trampoline in strong winds. Tie the trampoline down with ropes
attached to the trampoline top rail. Tie the trampoline down in a minimum of three places distributed
evenly across the trampoline frame.
Do not secure the legs as these may become misaligned and damage the trampoline. Dismantle or
remove the trampoline completely, if required. It may result in great danger if the trampoline is not
secured in strong winds.
ASSEMBLY AND MAINTENANCE INSTRUCTIONS
(frame, suspension system, mat, padding and enclosure) at the beginning of each season and
also at regular intervals. If these checks are not carried out, the trampoline could become
dangerous.
3

JUMPING INSTRUCTIONS
Fundamental Bounce
1. Start from a standing position with your head
erect and your eyes on the frame pad.
2. Swing your arms forward and up in a circular
motion.
3. Bring your feet together and point your toes
downward while in the air.
4. Keep your feet about 30 cm (15 in.) apart when
landing on the bed.
Knee Drop
1. Start bouncing from a standing position, keeping
your eyes on the frame pad.
2. Land on your knees, keeping your back straight
and your body erect.
3. Bounce back to an erect position.
Seat Drop
1. Land in a sitting position with your legs parallel to
the bed.
2. Place your hands on the bed beside your hips.
3. Push with your hands to return to an erect
position.
Front Drop
1. Start from a low bounce and land on the bed in a
prone position.
2. Keep your head up and your arms extended
forward on the bed.
3. Push with your arms to return to an erect position.
A certified trampoline instructor should be contacted to further develop your
trampoline skills.
4

WHAT YOU WILL NEED FOR BUILDING YOUR TRAMPOLINE
Safety glasses Mallet
To help build your trampoline, you will need gloves, safety glasses and a mallet.
Please note that these are not supplied with your trampoline.
ASSEMBLY INSTRUCTIONS
To assemble this trampoline we have provided you with our special spring pulling tool
(item N) and a cross head screwdriver (item O) and spanners (item K). During periods of
non-use, this trampoline can be easily disassembled and stored.
Please read the assembly instructions before beginning to assemble the product.
PRIOR TO ASSEMBLING
Please refer to pages 6-7 for part descriptions and numbers. The assembly steps use
these description and numbers as reference for your convenience.
Make sure that you have all parts listed. If you are missing any parts, please refer to page
22 for instructions on how to obtain any missing parts.
5
Gloves

TRAMPOLINE PARTS LIST
6

7

STEP 1: TRAMPOLINE PARTS
Lay out all the trampoline parts in groups, as shown in the picture. 1.
STEP 2: ASSEMBLING THE FRAME
8
2. Position the frame tubes (C,D,E,F) and T-connectors (J) as shown in the above image.
D
D
C
C
E E
F
F
J J
J
J
J
JJ J
3. Connect all the top rails (C,D,E,F) with T connectors (J).
Note: Product images are for illustration purposes only, component part colours may vary
dependent on which JumpPRO model you have purchased.

9
D
D
C
C
EE
F
F
J
J
J
J
J
J
J
J
4. Continue until you form a complete rectangle frame.
5. Attach the leg extensions (H) to the leg bases (I) securely.
6. Attach the trampoline legs you assembled, to the top rails as the images above show. Repeat this
step for all 4 corners. Ensure the holes in the bottom of the T-connectors are aligned with the holes
in the leg extensions (H).

10
STEP 3: ATTACHING THE BED
WARNING:
Be careful where you place your hands during spring assembly as connector points can pinch!
a
b
Note: It is easier to place one hand on the frame and pull the spring towards you, as shown above.
Make sure that "a" is attached to the D-rings of the jumping mat and "b" is attached to the
trampoline frame.

11
7. Slot 8pcs of springs (G) to the spring holes in the 4 corners of the top frame tubes.
Important: Springs must be attached the right way around and fully inserted into the holes
along the top of the frame.
8. Connect the other end of the springs onto the corresponding D-rings of the jumping mat (B).

12
9. To even out the tension and avoid over stretching the springs, continue connecting every few
springs in the above sequence until all springs are attached by using spring pulling tool (N).
STEP 4: FITTING THE FRAME PAD
10. Lay the frame pad sections (A) over the edge of the frame with the ties facing downwards.
11. Connect the sections together with the attached hook and loop sections.
11
10
9
12
17 13
14 18
20 16
15 19

12. Tie all the black straps onto the top rails. Do not tie them to the springs. The trampoline pad is
now fitted and you have completed step 4.
WARNING: The trampoline MUST NOT be used during construction.
STEP 5: ASSEMBLING THE ENCLOSURE POLES
13
13. Connect the bottom enclosure poles (R) to the upper enclosure poles (S).
14. Align the holes in the bottom enclosure poles with the holes in the top enclosure poles, fasten
with the screws (T) using the screwdriver provided (O).

14
L
LM
M
15. Attach the top enclosure pole caps (U) to the top of the enclosure poles (S), fasten with the
screws (T) and screwdriver (O).
IMPORTANT: Refer to the picture (IMAGE (A) above, to clearly see which way round to attach
the pole caps, the opening of the pole cap has to be on the same side as the outside bend of
the top enclosure pole facing outwards.
IMAGE (A)
16. Insert the fork screws (L) through the bottom enclosure poles (R). Use the plastic spacer,
supplied with the fork screws in between the bottom pole tubes and leg extensions. Tighten the
nuts of each fork screw with the bolts and spanners provided. Screw the screw caps (M) onto the
back of each nut of fork screws for protection.

W
STEP 6: ATTACHING THE FIBERGLASS RODS TO THE NET
W W
X
X
X
X
Y Y
YY
15
Size:
12FT X 8FT
Y Y
Y Y
X
X
X
XSize:
10FT X 7FT
9FT X 6FT
W W
W W
W W W
17. Lay out and position the fiberglass rods (W,X) and fiberglass corner connectors (Y) as above.

18. 12FT X 8FT: Use 3pcs of fiberglass rods A (W) to make the long fiberglass rods.
10FT X 7FT and 9FT X 6FT: Use 2pcs of fiberglass rods A (W) to make the long fiberglass rods as
images above show.
19. Use 2pcs of fiberglass rod B (X) to make a short fiberglass rods.
When assembled, there should be 2 long fiberglass rods for the long sides and 2 short fiberglass
rods for short sides. 16
Long fiberglass rod
(includes 3pcs of fiberglass rod A)
Short fiberglass rod
(includes 2pcs of fiberglass rod B)
Y
YY
Y
Size:
12FT X 8FT
Y
Y
Y
Y
Size:
10FT X 7FT
9FT X 6FT
Short fiberglass rod
(includes 2pcs of fiberglass rod B)
Long fiberglass rod
(includes 3pcs of fiberglass rod A)
Long fiberglass rod
(includes 2pcs of fiberglass rod A)
Long fiberglass rod
(includes 2pcs of fiberglass rod A)
Short fiberglass rod
(includes 2pcs of fiberglass rod B)
Short fiberglass rod
(includes 2pcs of fiberglass rod B)

Lay the safety net on the trampoline bed
17
There are 3 white dots on
each corner of the safety
net
The product label should be
on the front right hand
corner
The zipper and logo on the net should align
with the logo on the pad
Start the following steps (20 and 21) from the front right hand corner, where the product label is.
IMPORTANT - INSTALLING THE SAFETY NET

Note: The following steps (20-21) should be
completed whilst the net is laid out on the
trampoline bed.
20. Insert the fiberglass rods into the sewn
sleeves on the top of the safety net (P). Long
fiberglass rods for long sides and short fiberglass
rods for short sides.
Note: Make sure that the opening of the net (the
zipper) is placed in the middle of the long side of
the trampoline. Align the logo at the top of the net
with the logo on the pad. See IMAGE B
21. After inserting the fiberglass rods into the safety net both the long sides and short sides, connect
the short side to the long side with the fiberglass corner connectors (Y).
Push buttons need to be inserted into the corner pieces. Press the top of the push buttons together
and push in all the way to the end of the corner piece, making sure that the buttons pop out through
the holes. 18
IMAGE (B)

22. Connect the fiberglass rod to the top of the poles by clicking it into the pole caps (U). Repeat this
step for all 8 poles.
19