JumpSport 280 User manual

1
JumpSport, Inc.
1680 Dell Ave.
Campbell, CA 95008 U.S.A.
Patent info at: patents.jumpsport.com
Copyright © 2001-2017, by JumpSport, Inc. All rights reserved
P/N: INS-P-10470-01C
Retain address information for future use.
10ft—16ft* Safety Enclosures:
Models 280, 380, 480, and 480XT
User’s Manual
Assembly, Installation, Care, Maintenance, and Use Instructions
* If you plan to install this enclosure on a trampoline system that is less than 14’ (4.3m) in diameter, please note that the installation
instructions are different. Find the correct instructions online at www.jumpsport.com/pdf/smallerSE.pdf, scan the QR code below, or
contact JumpSport customer service at 408-213-2551.
WARNING
Read these materials prior to assembling and using this Trampoline Enclosure
DO NOT attempt or allow
somersaults. Landing on the
head or neck can cause serious
injury, paralysis or death, even
when landing in the middle of the
bed.
DO NOT allow more than one
person inside the trampoline
enclosure. Use by more than
one person at the same time
can result in serious injury.
Use trampoline only with mature, knowledgeable supervision.
DO NOT attempt to jump over
the barrier.
DO NOT intentionally rebound
off the barrier.
DO NOT hang from, kick, cut
or climb on the barrier.
The maximum user weight is:
Model 280: 200 pounds
Model 120 & 380: 230 pounds
Models 480 & 480XT: 295 pounds
Scan QR code for
alternate instructions:

2
Copyright Notice
This material is protected by United States copyright laws and is proprietary to JumpSport, Inc. Disclosure, reproduction, translation,
modification, or use of this document by anyone other than authorized employees, authorized users, or licensees of JumpSport
without the prior written consent of JumpSport, Inc. is prohibited.
The information in this document is subject to change without notice. JumpSport, Inc. shall not be liable for any damages resulting
from technical errors or omissions, which may be present in this document, or from use of this document.
Copyright © 1997-2017, by JumpSport, Inc. All rights reserved.
Instruction Manual P/N: INS-P-10470-01A
JumpSport 12ft Safety Enclosure Model 120 P/N: SEJ-S-11718-01
JumpSport 10ft—14ft Safety Enclosure Model 280 P/N: SEJ-S-11339-01
JumpSport 10ft—14ft Safety Enclosure Model 380 P/N: SEJ-S-11340-01
JumpSport 10ft—14ft Safety Enclosure Model 480 P/N: SEJ-S-11341-01
JumpSport 14.1ft—16ft Safety Enclosure Model 480XT P/N: SEJ-S-11342-01
Trademarks
JumpSport®, ProFlex™ Basketball Set, Game and Party Pak™, SureStep™ Trampoline Ladder, and BounceBoard Extreme™ are
trademarks of JumpSport, Inc.
All other brand or product names are trademarks or registered trademarks of their respective companies or organizations.
Patents
This product includes technology associated with one or more of the following U.S. Patents:
No. 6,053,845
No. 6,261,207
No. 6,840,891
No. 6,846,271
No. 7,060,001
Additional Patents Pending.
How to Contact Customer Support
Should you require customer service or technical support for your JumpSport Safety Enclosure, please contact JumpSport’s Customer
Service department at:
United States:
408-213-2551
6:00am—5:00pm Monday through Friday, Pacific Time
Australia:
1800-822-117

3
Contents
Chapter 1 Introduction 5
JumpSport ProFlex Basketball Set 6
Game and Party Pak 6
Chapter 2 Assembly and Installation Instructions 7
Preparation 7
Trampoline Placement 7
Tools 8
Parts List 8
Assembly 9
Type A Installation 14
Type B Installation 21
Final Steps 27
Disassembly 27
Chapter 3 Care and Maintenance Instructions 29
Inspection 29
Cold Weather Protection 29
Replacement Parts 29
Disassembly 29
Care and Maintenance Safety Checklist 30
Windy Conditions 31
Moving the Trampoline 31
Care 31
Chapter 4 Warning Information 33
Points of Safety 33
Before you Jump, Read this: 33
Landing on Springs or Frame 34
Bouncing off the Trampoline 34
Landing Incorrectly on the Mat 34
Chapter 5 Use Instructions 35
Safety Rules 35
Basic Skills 36
Bouncing 36
Stop Bounce 36
Arm Action 36
Bounce Variations 37
Basic Landing Positions 37
Seat Drop 37
Hands and Knees Drop 38
Front Drop 38
Series of Drops 39
Twisting Moves 39
Swivel Hips 39
Turntable 40
Twist Variations 40
Warranty Information Last Page

4
(This page left intentionally blank.)

5
Introduction 1
Congratulations on purchasing a JumpSport Safety Enclosure! We sincerely believe that you have purchased the finest
safety enclosure on the market. It has been engineered with safety, durability, and performance in mind.
Safe use of a trampoline also requires adequate knowledge of technique, as well as what not to do. Please read this
manual thoroughly for key points of safety.
Trampolines, being rebounding devices, propel the performer to unaccustomed heights and into a variety of body
movements. Therefore, it is emphasized that all purchasers, and all persons using the trampoline, become familiar with
the rules for safe use. Misuse and abuse of this trampoline is dangerous, and can cause serious injuries. The purchaser/
user of this piece of equipment is assuming a degree of risk for which JumpSport cannot be responsible.
Read this information thoroughly before allowing the trampoline to be used. Keep this manual available for your
review, and for review by all potential users. If there are questions please call JumpSport for further explanation.
Caution
Many users of our trampolines are children, and therefore need close supervision and rules to follow while playing on
the trampoline. These rules must be enforced by whomever is responsible for the care of the children. It is strongly
recommended that the buyer of this product go over the rules and recommendations in the packet of information
supplied, including those in this manual. It is also strongly recommended that these rules and recommendations be
supplemented with those of your own, for example: the time that jumping is allowed, when neighbors can visit, and so
on. These rules and recommendations should be reviewed with anyone who is going to jump on the trampoline. If it is
possible, review these rules with the parents or guardians of any visitors who may be jumping on the trampoline. See
Safety Rules (under the Use Instructions section) for more information.

6
Don’t miss out on these fun accessories and more at
www.jumpsport.com !
Bring the party to your
trampoline! The Game & Party
Pak is a great way to take
turns and have fun
participating in games while
you are waiting.
Convince your parents that
games provide the “structure"
you need in your life, and that
the Game & Party Pak is just
the solution. Plus, you can tell
them the Party Pak does big
words like:
 Enhances Athletic Building
Blocks
 Develops Agility, Stamina,
Balance, Coordination
 Improves Spatial
Awareness
(They won’t be able to turn you
down!)
Set Includes:
 Illustrated book of 20
games
 3 soft balls
 4 shock cords
 1 box of sidewalk chalk
 Hours of fun!
Let’s face it, kids have to look up
a lot: at parents, teachers, and
bigger brothers/sisters. With the
JumpSport ProFlex Basket-
ball Set, look down for a
change!
Whether you are into practicing
your outside shot or improving
your up-close game, the ProFlex
Basketball Set is a fun way to
avoid homework. Heck, athletic
scholarships pay for college
too!
 Our most popular
accessory!
 Easily installed to your
safety enclosure
 Set includes basketball
JumpSport ProFlex Basketball Set
Introduction
Game & Party Pak

7
Assembly and Installation
Instructions 2
Preparation
Before you begin assembling your JumpSport Safety Enclosure, make sure your trampoline is in a proper location.
Trampoline Placement
Caution: When deciding on where to place your trampoline, consider the following:
WARNING
Overhead Clearance Adequate overhead clearance is essential. A minimum of 24 feet from ground level
is recommended. Provide clearance for wires, tree limbs, and other possible hazards.
Lateral Clearance Lateral clearance is essential. Place the trampoline and trampoline enclosure away from
walls, structures, fences, and other play areas. Maintain a clear space on all sides of the
trampoline and trampoline enclosure.
Level Surface Place the trampoline and trampoline enclosure on a level surface before use.
Lighting Use the trampoline and trampoline enclosure in a well-lighted area. Artificial
illumination may be required for indoor or shady areas.
Security Secure the trampoline and trampoline enclosure against unauthorized and
unsupervised use.
Ground Clearance Remove any obstructions from beneath the trampoline and trampoline enclosure.
Note: The trampoline enclosure is only to be used as an enclosure for a trampoline of a size for which the enclosure
is designed.
Note: The owner and supervisors of the trampoline are responsible to make all users aware of practices specified in
the Use Instructions.
IMPORTANT: The best surface on which to place your trampoline is dirt or grass. However, if you plan to install the
trampoline on a very hard surface such as concrete or asphalt, a dense foam —similar to what can be found in
public playgrounds —should be installed under each leg. Contact JumpSport Customer Service if you have any
questions.
It is the responsibility of the purchaser to become familiar with all of the information in this booklet, to
convey the warnings to all users, and to enforce JumpSport’s rules for safe use.
This unit is not intended for commercial or public use, and such use is strictly prohibited.
The maximum user weight is up to: 200 pounds (Model 280), 230 pounds (Models 120 & 380), 295
pounds (Models 480 & 480XT), or the specified user weight rating of your trampoline—whichever is low-
er.

8
Assembly and Installation Instructions
Tools
Installation of the safety enclosure requires a 13mm socket wrench (included), or a deep socket with a ratchet or elec-
tric drill. An 8ft A-Frame ladder will be useful for some steps (use care and follow procedures for use). Safety glasses
and gloves are also recommended for safety.
Parts List
Your JumpSport Safety Enclosure is shipped with the parts shown below. Some parts will be located in a smaller inner
box. If any parts are missing, immediately call JumpSport Customer Service at 408-213-2551.
Note: Do NOT discard the foam tubing (Reference #3 and #4); it is needed to make the pole assemblies. It is not
just packing material. Not all poles will have foam around them. And do NOT remove any caps from the ends of any
of the support poles.
Acorn nut
Ref. #7g
Nylock nut
Ref. #7f
Reference # Part # Description Quantity
1POL-A-10238-01 Lower support pole, with snap-button/thru-bolt 8
2POL-P-10118A Upper support pole, notch at one end 8
3FOA-P-10078A Long foam tubing (1 tube packed over 1 pole) 8
4FOA-P-10103A Short foam tubing (2 tubes packed over 1 pole) 8
5SLE-P-11467A Pole sleeve, blue vinyl 8
6CAP-P-10075A Ball end cap 8
7BOL-P-20992-00 Bolt, Carriage, M8 X 1.25 X 75mm long 16
8NUT-P-20991-00
Nut, Locking, Barrel, Serrated Flange, M8 X 1.25
X 23mm depth 16
9SPA-P-10083 Spacer, round, black, copolymer 16
10
NET-P-11198A (120 net)
NET-P-11522A (280/380 net)
NET-P-11523A (480 net)
NET-P-10469A (480XT net) Safety net 1
11 BUN-P-10126A 1ft bungee, loop at one end, hook at other end 8
12 STR-P-10115A
10.5ft pole strap, loop at one end
(Depending on your trampoline and safety
enclosure, not all straps will be used.) 16
13 BUN-P-10125A
6ft bungee, loop at one end, hook at other end
(not included with Model 280) 8
14 TOO-P-21468-00 Socket wrench,13mm 1

9
The following pages contain diagrams, pictures, and written instructions for assembling your JumpSport Safety
Enclosure. The “Ref. #” mentioned in many steps is referring to the “Reference #” column of the parts list on the
previous pages.
Familiarize yourself with the Assembly and Installation Instructions before beginning installation.
For installation questions, please contact JumpSport’s Customer Service department at:
United States:
408-213-2551
6:00am—5:00pm Monday through Friday, Pacific Time
Australia:
1800-822-117
Assembly and Installation Instructions
Assembly
Note: We recommend at least 2 people participate in assembling the safety enclosure. Use page 8 to help with part
names and numbers.
1) Build all pole assemblies as shown. Pole sleeve and foam will fit tightly up inside ball end cap, and notch in ball end cap will fit
inside notched end of upper pole. See page 8 for detailed part descriptions.
Lower pole (Ref. #1) Upper pole (Ref. #2)
Long foam tubing (Ref. #3) Short foam tubing (Ref. #4)
Pole sleeve (Ref. #5)
Ball end cap (Ref. #6)
CAUTION
Pinch point.
Pay careful attention to hand
position when connecting
tubes.
Top of pole sleeve
(narrow end)
Top of lower pole
(narrower end
with snap button)
Top of upper pole
(notched end)

10
Assembly and Installation Instructions
3) Tighten the two nuts evenly, using the hand wrench (# 14). Make sure that the carriage bolt does not spin by making sure the
head is fully seated in the square hole on the enclosure pole. Nuts are snug when the poles are firmly attached to the trampoline leg
with no movement. It is OK if the wings on the spacers begin to yield.
IMPORTANT: Be sure nothing is
caught between pole and leg
(including pole sleeve, foam
tubing, frame pad, etc.) before
tightening the bolts.
Bolt
Ref. #7
Nut
Ref. #8
Spacer
Ref. #9
Bolt
Ref. #7 Spacer
Ref. #9
Nut
Ref. #8
2) Using the hardware provided, connect a pole to the outside of each trampoline leg:
 Line up bottom of the enclosure pole with the existing trampoline leg so both holes match, and the square holes on the enclosure
pole face out, and indents at hole face toward the frame.
 Insert bolt #7 through the square enclosure pole hole and through pole spacer #9 at both locations on the enclosure pole.
 Insert the bolts through the trampoline leg holes.
 Insert nut #8 through the trampoline leg and at both locations, and hand-tighten.
Make sure indent-
ed dimples on
enclosure poles
face IN, toward the
trampoline frame.
Verify that holes on
frame are aligned, and
that the indented hole
on vertical leg faces
OUT (if applicable).