JUNIOR JNR-8153 User manual

JNR 150L Wash
JNR-8153
PR LIGHTING LTD.
http://www.pr-lighting.com
1582 Xingye Avenue, Nancun Panyu
Guangzhou, 511442 China
TEL: [phone]
The following points have to be considered during the inspection:
1) All screws for installing the devices or parts of the device have to be tightly connected
and must not be corroded.
2) There must not be any deformations on the housing, color lenses, fixations and
installation spots (ceiling, suspension, trussing).
3) Mechanically moved parts must not show any traces of wearing and must not rotate with
unbalances.
4) The electric power supply cables must not show any damage, material fatigue or sediments.
Fur ther instructions depending on the installation spot and usage have to be adhered by a
skilled installer and any safety problems have to be removed.
In order to make the lights in good condition and extend the life time, we suggest a regular
cleaning to the lights.
1) Clean the inside and outside lens each week to avoid the weakneness of the lights due to
accumulation of dust.
2) Clean the fan each week.
3) A detailed electric check by approved electrical engineer each three month, make sure
that the circuit contacts are in good condition, prevent the poor contact of circuit from
overheating.
We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never
use alcohol or solvents.
There are no serviceable parts inside the device. Please refer to the instructions under
“Installation instructions”.
Should you need any spare parts, please order genuine parts from your local dealer.
MAINTENANCE AND CLEANING
10
Disconnect from mains before starting maintenance operation.
CAUTI ON

.01.
If the device has been exposed to temperature changes due to environmental changes,
do not switch it on immediately. The arising condensation could damage the device.
Leave the device switched off until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be
earthed.
The electric connection must carr y out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would
be the case, replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it.
Only handle the power cord by the plug. Never pull out the plug by tugging the power
cord.
During initial start-up some smoke or smell may arise. This is a normal process and
does not necessarily mean that the device is defective, it should decrease gradually.
Please don't project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm
distance with wall for smooth air flow, so there should be no shelter for fans and
ventilation for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively
replaced by the manufacturer or his service agent or a similar qualified person in order
to avoid a hazard.
This device has left the factory in perfect condition. In order to maintain this
condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this user manual.
CAUTI ON
Bec areful with your operations.With a dangerous voltage you cansuffer a
dangerous electric shock when touching wires!
IMPORTANT
Damages caused by the disregard of this user manual are not subject to warranty.
The dealer will not accept liability for any resulting defects or problems.
SAFETY INSTRUCTIONS
1DMX CHANNELS
9
0-255
0-255
0-255
0-255
0-225
226-235
236-255
0-31
32-63
64-95
96-127
128-159
160-191
192-223
224-255
0.255
0-255
0-255
0-255
0-255
0-19
20-29
30-39
40-79
80-89
90-99
100-119
120-139
140-159
160-179
180-199
200-219
220-239
240-255
PAN movement
Fine control of PAN movement
Forwards infinite PAN rotation from slow to fast
TILTmovement
Max to min speed
Blackout by movement
No function
Shutter closed
Shutter open
Strobe effect slow to fast
Shutter open
Pulse-effect in sequences slow to fast
Shutter open
Random strobe effect slow to fast
Shutter open
Dimmer 0%...100%
0-100%Red dimmer from dark to bright
0-100%Green dimmer from dark to bright
0-100%Blue dimmer from dark to bright
0-100%White dimmer from dark to bright
No Function
No Function
No Function
No Function
All motor reset
Scan motor reset
Internal program 1
Internal program 2
Internal program 3
Internal program 4
Internal program 5
Internal program 6
Internal program 7
Internal sound rogram 1
Mode/CH Values Description
16b
1
2
3
4
5
6
7
8
9
10
11
12
PAN
PAN-fine
TILT
TILT-fine
Speed PAN/
TILT
Shutter
Dimmer
Red
Green
Blue
White
Special
function
8b
1
2
3
4
5
6
7
8
9
10
Function
.10.

Thank you for choosing our JNR 150L Wash. For your own safety, please read this
manual before installing the device. This manual covers the important information
on installation and applications. Please install and operate the fixture with following
instructions. Meanwhile, please keep this manual well for future needs.
The is made of a new type of high temperature strength of
engineering plastics and cast aluminum casing with nice outlook . The fixture is
designed and manufactured strictly following CE standards, complying with
international standard DMX512 protocol. It’s available independently controlled
and linkable with each other for operation. And it is applicable for large-scale live
performances, theater, studio, nightclubs and discos.
The adopts 1PCS 4-IN-1 150W LEDs which features high brightness
and stability. Please carefully unpack it when you receive the fixture and check
whether it is damaged during the transportation. And please check whether the
following items are included inside the box:
JNR 150L Wash
JNR 150L Wash
.02.
UNPACKING
2
①
JNR 150L Wash
Signal Cable
Power Cable
Omega Clamp
Safety Cable
User Manual
1PC
1PC
1PC
1PC
1PC
1PC
①
②
③
④
⑤
⑥
④
⑤⑥
②
③
Euro Standard UK Standard USA Standard
OPTIONAL
.09.
MENU OPERATIONS
8
001-XXX
CH12
CH10
Program 1~8
Alone
Master
Yes/No
Wire DMX
Wireless DMX
Act WDMX & Out
Reverse Pan (On/Off)
Program 1~8
Alone
Master
Reverse Tilt (On/Off)
Select Pan 630°/540° /360°
Select Tilt 270°/180°/90°
Mic sensitivity 0~99%
OFF Signal Mode (On/Off)
XXX℃/℉
V1.0~v9.9
Total Reset
Pan/Tilt Reset
PAN=XXX......
Pan
Pan Fine
Tilt
Tilt-Fine
Move Speed
Strobe
Dimmer
Green
Red
White
Blue
000-255
Dmx Address
Channel Mode
Auto Run
Music Control
Reset Default
Signal Set
Pan/Tilt
UI SET
Temperature
Software Version
Reset
Channel
Calibration
MENU
Function
Mode
Option
Information
Manual
Control
ADVANC ED
(Ac cess Co de 088)
DMX address setting
Standard chan nel
Vector channel
Alone Mode
Sound Mode
Overloading factory all
parameters
Wrie DMX I nput
Wriele ss DMX Input
Wireless DMX input, Wire DMX
output signal at the same time
Pan scan reverse
Program
Program
Alone Mode
Sound Mode
Tilt sca n reverse
Pan angle selec t
Tilt ang le select
Mic sensitivi ty Setting
No DMX signa l, Ke ep the original
State(No )R eset state
Current temperature
Software version
Reset all
Pan/Ti lt reset
Channel value c ontrol
Pan
Pan Fine
Tilt
Tilt-F ine
Move Speed
Strobe
Dimmer
Green
Red
White
Blue
Calibration F unction

.03.
Specifications
Input Voltage:
LED Quantities:
Control Signal:
Control Channel:
Power Consumption:
Dimensions:
Packing Dimensions:
Net Weight:
Gross Weight:
Features
AC90-260V 50/60Hz
DMX512,master-slave and sound activated or auto operation
10/12 DMX Channels USITT DMX-512
135W
260(D)*150(W)*348(H)mm
345(D)*235(W)*445(H)mm
5.54kg
7.56kg
1*150W COB 4-in-1 LED(RGBW)
FEATURES & SPECIFICATIONS
3
A 150W COB 4-in-1 LED lamp (RGBW)
50000 Hours life span and low power consumption
8/16 Bit smooth and precise resolution for PAN/TILT movement
360°/540°/630° PAN and 90°/180°/270° TILT movement
PAN/TILT inversion available
Scan position memory, auto reposition after unexpected movement
Specific high precision 26°optic lens integrated in a alum-oxidized reflector
Improved optics and flat beam field
Infinite color mixing capability (CMY)
Pure and even color coverage
0-100% Smooth linear LED dimmer
25T/sec high speed LED shutter/strobe effect with variable speed
Preset variable/random strobe and dimming pulse effect
10/12 DMX channels USITT DMX-512
DMX512, master-slave, and sound activated controllable or auto operation
(7 built-in programs)
DMX recorder and edit function integrated
2.4” TFT LCD display (320*240pix) with 4 control buttons
Display inverted capable
POWRECON connector IN/OUT
3-Pin XLR connectors IN/OUT
Low noise fan cooling system
Constant temperature readout and management function
-35℃-45℃ max ambient temperature
IP20 protection rating
55dB at 3’dB rating
1*1/4 turn fastening Omega clamp
1*Safety attachment point
For installations where the DMX cable has to run a long
distance or is in an electrically noisy environment, such as
in a discotheque, it is recommended to use a DMX
terminator. This helps in preventing corruption of the
digital control signal by electrical noise. The DMX
terminator is simply an XLR plug with a 120 Ω resistor
connected between pins 2 and 3,which is then plugged
into the output XLR socket of the last fixture in the chain.
Please see illustrations below.
12
3
PIN3
PIN2
120 Ω
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
.08.

.04.
PHOTOMETRIC DATA
4
5°Beam Angle LUX 0.0929=FC×
Photometric Beam Angle Data
174 / 1870 27 / 297 7 / 77
1m (3.3ft) 3m (9.8ft) 5m (16.4ft)0m (0ft)
(FC/LUX)
245 / 2640 41/ 440 9/ 93
245 / 2640
338 /4180
42 / 451
71 / 770
9/ 93
11 / 118
971 / 10450 169 / 1815 31 / 330
R
G
B
W
RG BW
26°
12 / 132
17/ 187
18 / 198
29 / 308
77/ 825
7m (23.0ft)
.07.
DMX Output
3-Pin XLR Socket
DMX Input
3-Pin XLR Socket
1:Ground
2:Data(-)
3:Data(+)
1 2
3
12
3
1
2
3
1
2
3
COMMON
DMX+
DMX-
DMX512 IN
3-PIN XLR
DMX512 OUT
3-PIN XLR
2 1
Regardless of the rigging option you choose for your , always be sure
to secure your fixture with a safety cable. The fixture provides a built-in rigging point
for a safety cable on the hanging bracket as illustrated above. Be sure to only use the
designated rigging point for the safety cable and never secure a safety cable to a
carr ying handle.
JNR 150L Wash
Connect the provided XLR cable to the female 3-pin XLR output of your controller and
the other side to the male 3-pin XLR input of the moving head. You can chain multiple
Moving head together through serial linking. The cable needed should be two core,
screened cable with XLR input and output connectors. Please refer to the diagram
below.
DMX-512 connection with DMX terminator
DMX-512 CONTROL CONNECTIONS
7
POWER IN
DMX IN
FUSE
POWER IN
DMX IN
DMX OUT
POWER SWITCH

· The is for wash effect for on-site decoration purpose.
· Don’t turn on the fixture if it’s been through severe temperature difference like
after transportation because it might damage the light due to the environment
changes. So make sure to operate the fixture until it is in normal temperature.
· This light should be keep away from strong shaking during any transportation or
movement.
· Don’t pull up the light by only the head, or it might cause damages to the
mechanical parts.
· Don’t expose the fixture in overheat, moisture or environment with too much dust
when installing it. And don’t lay any power cables on the floor. Or it might cause
electronic shock to the people.
· Make sure the installation place is in good safety condition before installing the
fixture.
· Make sure to put the safety chain and check whether the screws are screwed
properly when installing the fixture.
· Make sure the lens are in good condition. It’s recommended to replace the units if
there are any damages or severe scratch.
· Make sure the fixture is operated by qualified personnel who knows the fixture
before using.
· Keep the original packages if any second shipment is needed.
· Don’t try to change the fixtures without any instruction by the manufacturer or
the appointed repairing agencies.
· It is not in warranty range if there are any malfunctions from not following the
user manual to operate or any illegal operation, like shock short circuit, electronic
shock, lamp broke, etc.
JNR 150L Wash
.05.
OPERATION INSTRUCTIONS
5
Cautions: For added protection mount the fixtures in areas outside walking paths,
seating areas, or in areas were the fixture might be reached by unauthorized
personnel.
Before mounting the fixture to any surface, make sure that the installation area can
hold a minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such
as an appropriate safety cable.
INSTALLATIONS
6
Never stand directly below the device when mounting, removing, or servicing the
fixture.
from a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture
is kept at least 0.5m (1.5 ft) away from any flammable materials (decoration etc.).
Always use and install the supplied safety cable as a safety measure to prevent
accidental damage and/or injury in the event the clamp fails.
Mounting points: Overhead mounting requires extensive experience, including
amongst others calculating working load limits, a fine knowledge of the installation
material being used, and periodic safety inspection of all installation material and the
fixture. If you lack these qualifications, do not attempt the installation yourself.
Improper installation can result in bodily injury.
Be sure to complete all rigging and installation procedures before connecting the
main power cord to the appropriate wall outlet.
Clamp mounting: The provides a unique mounting bracket assembly
that integrates the bottom of the base, and the safety cable rigging point in one unit
(see the illustration below). When mounting this fixture to truss be sure to secure an
appropriately rated clamp to the included omega bracket using a M10 screw fitted
through the center hole of the “omega bracket”. As an added safety measure be sure
to attached at least one properly rated safety cable to the fixture using on of the
safety cable rigging point integrated in the base assembly.
JNR 150L Wash
.06.
②
① Omega Bracket
② Satety Clamp
③ Safety Cable
④ 1/4 Turn Quick-Lock Fasteners
①
③
④
1/4 Turn 1/4 Turn