Justin JED700M User manual

Module: SKD203
OWNER’S GUIDE
JustIn JED700M E-Drumset

Congratulations!
Thank you for purchasing this digital drum set. The drum set has been Developed to
act and play like a drum set but with greater ease. Before you use the instrument, we
recommend you to read through this manual.
Taking care of Your Digital Drum Set
Location
- Do not expose the unit to the following
Conditions to avoid deformation,
discoloration or more serious damage.
- Direct sunlight.
- High temperature (near a heat)source,
Or in car during the day time).
- Disconnect all cables before moving
Power Supply
-make sure to use the suitable AC adaptor,
and also make sure the ac outlet voltage
at your country matches the input voltage
specified on the AC
AC adaptor's label.
-Turn the power switch OFF When the
Instrument is not in use.
-An AC adaptor should be unplugged
from the AC outlet if the instrument is
not be used for an extended period of
time.
- Unplug the AC adaptor during electric
storms.
-Avoid plugging the AC adaptor into
-The same AC outlet as appliance with
high power consumption, such as
electric heaters or ovens. Also avoid
using multi-plug adaptors since these
can result in reducing the sound quality,
operation errors, and possibly damage.
Turn Power OFF When Making
Connections
- To avoid damage to the instrument
and other devices to which it is
Connected, turn the power switches of
all related device OFF prior to connecting
or disconnecting cables.
Handling and Transport
- Never apply excessive force to the
controls, connectors or other parts of
the instrument.
- Always unplug cables by gripping the
plug firmly, but not pulling on the cable.
- Disconnect all cables before moving
The instrument.
- Physical shocks caused by dropping,
bumping, or placing heavy objects on
the instrument can result in scratches
more serious damage.
Cleaning
- Clean the unit with a dry soft cloth.
- A Slightly damp cloth may be used to
Remove stubborn grime and dirt.
- Never use cleaners such as alcohol
or thinner.
- Avoid placing vinyl object on top of
The unit (uinyl can stick to and
discolor the surface).
Electrical Interference
- This instrument contains digital
circuitry and may cause interference
if placed too close to radio or
television receivers. If this occurs,
move the instrument further away
from the affected equipment.

Congratulations!
Thank you for purchasing this digital drum set. The drum set has been Developed to
act and play like a drum set but with greater ease. Before you use the instrument, we
recommend you to read through this manual.
Taking care of Your Digital Drum Set
Location
- Do not expose the unit to the following
Conditions to avoid deformation,
discoloration or more serious damage.
- Direct sunlight.
- High temperature (near a heat)source,
Or in car during the day time).
- Disconnect all cables before moving
Power Supply
-make sure to use the suitable AC adaptor,
and also make sure the ac outlet voltage
at your country matches the input voltage
specified on the AC
AC adaptor's label.
-Turn the power switch OFF When the
Instrument is not in use.
-An AC adaptor should be unplugged
from the AC outlet if the instrument is
not be used for an extended period of
time.
- Unplug the AC adaptor during electric
storms.
-Avoid plugging the AC adaptor into
-The same AC outlet as appliance with
high power consumption, such as
electric heaters or ovens. Also avoid
using multi-plug adaptors since these
can result in reducing the sound quality,
operation errors, and possibly damage.
Turn Power OFF When Making
Connections
- To avoid damage to the instrument
and other devices to which it is
Connected, turn the power switches of
all related device OFF prior to connecting
or disconnecting cables.
Handling and Transport
- Never apply excessive force to the
controls, connectors or other parts of
the instrument.
- Always unplug cables by gripping the
plug firmly, but not pulling on the cable.
- Disconnect all cables before moving
The instrument.
- Physical shocks caused by dropping,
bumping, or placing heavy objects on
the instrument can result in scratches
more serious damage.
Cleaning
- Clean the unit with a dry soft cloth.
- A Slightly damp cloth may be used to
Remove stubborn grime and dirt.
- Never use cleaners such as alcohol
or thinner.
- Avoid placing vinyl object on top of
The unit (uinyl can stick to and
discolor the surface).
Electrical Interference
- This instrument contains digital
circuitry and may cause interference
if placed too close to radio or
television receivers. If this occurs,
move the instrument further away
from the affected equipment.
Content:
Panel description.................................1
Connect with external devices ..........6
Connect audio system&drum amp.....6
Connect heahpone ....6.........................
Connect MP3 or CD player................6
Connect PC .......................................6
Connect MIDI keyboard.....................7
Power supply and switch...................7
Select drum kit .8..................................
Playing the pads.................................8
Use metronome ...............................10
Adjust click.......................................10
Adjust click tempo............................10
Edit and create owner’s drum kit......11
Change pad voice.............................11
Change pad volume..........................11
Change pad L/R CH pan 11..................
Change MIDI output pitch 12................
Save setting to user drum kit............12
Adjust pad Trigger.....................13
Adjust pad curve 13...............................
Adjust pad threshold.........................14
Eliminate pad crosstalk 14.....................
Basic operating...........................8
Performing.................................10
Mask Time.............................14
Adjust pad sensitivity ...............14
Eliminate pad crosstalk 4.....................1
Retrig Cancel: ........ 15..................
SAVE TRIGGER SETTING . 5.......1
Reload to default setting...................17
Drumrim option.............................17
DEMO SONG playing 18.................................
Select DEMO SONG 18..................................
Select DEMO SONG........................18
Adjust volume of accompaniment
& drum...........................................16
Mute Drums of DEMO SONG...........18
Adjust DEMO SONG tempo..............18
Adjust pad effect 16........................................
EQ setting................................................16
Ambience setting 16.....................................
Recording quickly 19.....................................
Play back performance...................19
MIDI setting 20.................................................
MIDI connection.......................................20
Connect with external audio device ..20
Change pad voice............................20
MIDI list 21.......................................................
Trouble shooting 23........................................
Audio source parameter 23.............................
Drum kit list 24................................................
Voice list 26.....................................................
DEMO SONGlist 28.........................................
Record your performance ................19

Panel Description
12. KIT
Switch to drum kit quickly.
15. VOICE
Quickly switch to voice setting.
16. SET UP
Set up metronome/drum/DEMO SONG etc.
13. CANCEL
Cancel the operation or go back to the former menu.
14. DRUM OFF
drum mutes when DEMO SONG is being played.
11. Pad indication
Indicates the working pad or tests the pad, or set
the pad parameter.
(hold the button to change the value continuously.)
17. Direction key
:Menu selection
:change the parameter
1
2
3
5
4
6
7
9
10
8
11
1
17
15
14
16
13
12
6. RECORD
Record the drum set sound.
8. PLAY
Play/pause the recorded sound.
9. CLICK
Play the metronome.
7. TEMPO
Enter into the tempo setting quickly.
10. SONG
Enter into DEMO SONG setting quickly.
3. MASTER VOLUME
Adjust the volume of phone and line output.
1. LCD
Displays the menu content.
2. Power switch
Turns on /off the power supply.
5. START/STOP
Start or stop playing DEMO SONG.
4. SAVE
Save the parameter setting.
Save the current kit setting.
Front panel

Panel Description
12. KIT
Switch to drum kit quickly.
15. VOICE
Quickly switch to voice setting.
16. SET UP
Set up metronome/drum/DEMO SONG etc.
13. CANCEL
Cancel the operation or go back to the former menu.
14. DRUM OFF
drum mutes when DEMO SONG is being played.
11. Pad indication
Indicates the working pad or tests the pad, or set
the pad parameter.
(hold the button to change the value continuously.)
17. Direction key
:Menu selection
:change the parameter
1
2
3
5
4
6
7
9
10
8
11
1
17
15
14
16
13
12
6. RECORD
Record the drum set sound.
8. PLAY
Play/pause the recorded sound.
9. CLICK
Play the metronome.
7. TEMPO
Enter into the tempo setting quickly.
10. SONG
Enter into DEMO SONG setting quickly.
3. MASTER VOLUME
Adjust the volume of phone and line output.
1. LCD
Displays the menu content.
2. Power switch
Turns on /off the power supply.
5. START/STOP
Start or stop playing DEMO SONG.
4. SAVE
Save the parameter setting.
Save the current kit setting.
Front panel
Rear panel connection
21. TOM4
Connect with TOM4
20. CRASH2
Connect with CRASH2
19 -OUT PUT- L/mono R
L/R channel, connect with the output
connector of audio system or drum
amplifier.
18. PHONE
Headphone output connector.
22. AUX IN
External stereo input connector, e.g.
Mp3 or CD player.
24. USB
Connect with PC connector (MIDI in/out
via USB)
23. IN---MIDI---OUT
Connect with the connector of external
device which has MIDI.
25. DC IN
Adaptor connector, 5V DC.
26. PAD connection
Pad signal input connector, including: KICK,
TOM1--3, SNARE, RIDE,CRASH,HI-HAT
CTRL
2
26
1918 20 21 22 23 24 25

Panel Description
11. KIT
Switch to drum kit quickly.
14. VOICE
Quickly switch to voice setting.
15. SET UP
Set up metronome/drum/DEMO SONG etc.
13. CANCEL
Cancel the operation or go back to the former menu.
12. DRUM OFF
drum mutes when DEMO SONG is being played.
10. Pad indication
Indicates the working pad or tests the pad, or set
the pad parameter.
(hold the button to change the value continuously.)
16. Direction key
:Menu selection
:change the parameter
3
8. RECORD
Record the drum set sound.
9. PLAY
Play/pause the recorded sound.
7. CLICK
Play the metronome.
5. TEMPO
Enter into the tempo setting quickly.
6. SONG
Enter into DEMO SONG setting quickly.
2. MASTER VOLUME
Adjust the volume of phone and line output.
1. LCD
Displays the menu content.
3. START/STOP
Start or stop playing DEMO SONG.
4. SAVE
Save the parameter setting.
Save the current kit setting.
1
2
3 45
6
7
8
9
10
16
11
12
13
14
15
Front panel

Panel Description
11. KIT
Switch to drum kit quickly.
14. VOICE
Quickly switch to voice setting.
15. SET UP
Set up metronome/drum/DEMO SONG etc.
13. CANCEL
Cancel the operation or go back to the former menu.
12. DRUM OFF
drum mutes when DEMO SONG is being played.
10. Pad indication
Indicates the working pad or tests the pad, or set
the pad parameter.
(hold the button to change the value continuously.)
16. Direction key
:Menu selection
:change the parameter
3
8. RECORD
Record the drum set sound.
9. PLAY
Play/pause the recorded sound.
7. CLICK
Play the metronome.
5. TEMPO
Enter into the tempo setting quickly.
6. SONG
Enter into DEMO SONG setting quickly.
2. MASTER VOLUME
Adjust the volume of phone and line output.
1. LCD
Displays the menu content.
3. START/STOP
Start or stop playing DEMO SONG.
4. SAVE
Save the parameter setting.
Save the current kit setting.
1
2
3 45
6
7
8
9
10
16
11
12
13
14
15
Front panel
Rear panel connection
24. TOM4
Connect with TOM4
25. CRASH2
Connect with CRASH2
22 -OUT PUT- L/mono R
L/R channel, connect with the output
connector of audio system or drum
amplifier.
23. PHONE
Headphone output connector.
26. PAD connection
Pad signal input connector, including: KICK,
TOM1--3, SNARE, RIDE,CRASH,HI-HAT
CTRL
4
17 18 19 20
2221 23
24
25
26
21. AUX IN
External stereo input connector, e.g.
Mp3 or CD player.
19. USB
Connect with PC connector (MIDI in/out
via USB)
20. IN---MIDI---OUT
Connect with the connector of external
device which has MIDI.
17. DC IN
Adaptor connector, 5V DC.
18. Power switch
Turns on /off the power supply.

LCD initial interfaces
1).CLICK=4/4(default value when on):metronome parameter indication
2).TEMPO=100(default value when on):tempo parameter indication
3).KIT01 POP01(default value when on): drum kit indication
4).SONG01(default value when on): demo song indication
5).DRUM ON(default value when on): mutes the drum sound of demo song.
KIT01 POP01
SONG01 DRUM ON
CLICK=4/4 TEMPO=100
5

LCD initial interfaces
1).CLICK=4/4(default value when on):metronome parameter indication
2).TEMPO=100(default value when on):tempo parameter indication
3).KIT01 POP01(default value when on): drum kit indication
4).SONG01(default value when on): demo song indication
5).DRUM ON(default value when on): mutes the drum sound of demo song.
KIT01 POP01
SONG01 DRUM ON
CLICK=4/4 TEMPO=100
5
Connect to audio system or amplifier
When connecting with audio system or drum amplifier, use a cable to connect with L/mono R of the
audio system and the drum amplifier.
Note:
1).Connect with L/mono connector when connecting with mono audio device.
2).Connect with L/mono and R connector when connecting with stereo audio device.
3).The volume is controlled by the master volume knob of drum kit and of the audio device.
Connect headphonesto
The audio source box has 1/4” headphone connector(if use a 1/8” headphone ,use an
adaptor), the volume is controlled by the volume knob of the audio source box.
Connect to MP3 or CD player
Connect the output of MP3 or CD player or other audio sources with AUX.IN connector. The
input signal can be mixed with the drum signal, strike the pads according to the rhythm of
the input signal.
1. Connect the computer via USB Receive and send MIDI signal.
Connect to PC
6
Connect with external devices

2.Connect the computer via MIDI port
MIDI IN: receiver MIDI signal of computer or other devices.
MIDI OUT: send pad performance signal to external MIDI devices or computer.
MIDI connector: If you're using an external MIDI keyboard or pads to control the digital drum, make
connections as shown. Here, it is used as a sound module.
Connect with a MIDI keyboard
Make sure the power is switched OFF. Connect the power adaptor to the DC IN jack on the side panel.
After confirming that all connections have been completed, rotate the volume knob to the left (minimum
volume level) before switching the power on. Set the power switch to the “ON” position. The KIT
indicator on LCD will light up and the display will show kit number 01 pop 01.
Note:
Make sure the power is switched OFF when connecting the drum module with external devices.
Power supply and switch
7

2.Connect the computer via MIDI port
MIDI IN: receiver MIDI signal of computer or other devices.
MIDI OUT: send pad performance signal to external MIDI devices or computer.
MIDI connector: If you're using an external MIDI keyboard or pads to control the digital drum, make
connections as shown. Here, it is used as a sound module.
Connect with a MIDI keyboard
Make sure the power is switched OFF. Connect the power adaptor to the DC IN jack on the side panel.
After confirming that all connections have been completed, rotate the volume knob to the left (minimum
volume level) before switching the power on. Set the power switch to the “ON” position. The KIT
indicator on LCD will light up and the display will show kit number 01 pop 01.
Note:
Make sure the power is switched OFF when connecting the drum module with external devices.
Power supply and switch
7
8
Basic operating
Select a drum kit
After powering up, the digital drum will be in kit menu (kit indicator on ). the display should
look like the following figure. there are 3 ways to activate the drum kit menu:
1.Use the direction key to select drum kit.41 sets of drum kits in all.
29 sets of preset drum kits:KIT01---29
12 sets of user drum kits: USER01---12
2.Pressing the Pad Select buttons allows you to preview the
current kit (fixed tempo).
KIT01 POP01
SONG01 DRUM ON
CLICK=4/4 TEMPO=100
3.Hit the pads to play the current kit.
Play pads
Similar to an acoustic drum kit, the digital drum
responds differently to various playing techniques
and dynamics. All the pads senses the striking force.
and some voices change tone depending on the
striking force.
Drum pad and rim shot
The digital drum pad detects head and Side stick
(Side stick Are different from the pad shots).
Note:
1.SNARE and TOM1-TOM3 are dual channels.
2.RIDE: it delivers RIDE BELL sound when hit
strongly, and RIDE CYMBAL sound when hit
Slightly.
3.SNARE delivers one sound when hit the pad
. rim strongly
Cymbal bow shot and choke
CRASH and RIDE have the bow shot
and choke, e.g. hit the cymbal or the
rim then hold the rim to CRASH or RIDE
sound.

9
HI-HAT
The Hi-Hat sound varies depending on the position of the Hi-Hat pedal:
Open Hi-Hat: Strike the Hi-Hat pad without pressing the pedal.
Closed Hi-Hat: Strike the Hi-Hat pad with the pedal pressed completely down.
Pedal Close: Press the pedal completely down without striking the pad.
Half-open Hi-Hat:Strike the Hi-Hat pad with the pedal pressed halfway down
Pad
Cross stick
CYMBAL
RIM
Rim shot
(Hit strongly)

9
HI-HAT
The Hi-Hat sound varies depending on the position of the Hi-Hat pedal:
Open Hi-Hat: Strike the Hi-Hat pad without pressing the pedal.
Closed Hi-Hat: Strike the Hi-Hat pad with the pedal pressed completely down.
Pedal Close: Press the pedal completely down without striking the pad.
Half-open Hi-Hat:Strike the Hi-Hat pad with the pedal pressed halfway down
Pad
Cross stick
CYMBAL
RIM
Rim shot
(Hit strongly)
Use metronome
1. User can use the [CLICK] button to turn on/off metronome.
2. use the direction key to select the click items to reset.
KIT01 POP01
SONG01 DRUM ON
CLICK=4/4 TEMPO=100
Adjust click
3. When the metronome plays at the click and tempo, such as the LCD displays, the CLICK flashes,
user can use the direction key to change click.
10
Performing
4. In the click item, press [SET UP] button to set click tone parameters.
1).VOICE TYPE=01 user can adjust the voice type (01---03)
2).VOICE VOL=127 user can adjust the voice volume (000---127)
3).When adjusting parameters, press [SET UP] button to reset.
CLICK VOICE OPTION
VOICE TYPE=01
VOICE VOL=100
User can adjust the click tempo. When playing metronome, press tempo and playing adjust
(030---300)
1.Press [TEMPO] to adjust tempo speed.
2.Use the direction key to change tempo speed.
Adjust click tempo
KIT01 POP01
CLICK=4/4 TEMPO=100
SONG01 DRUM ON

Edit and create owner’s drum kit
In the drum kit menu, user can change parameter according to the playing style then save it.
1.Press [KIT] to select the drum kit
2.Use the direction key to switch to the desired drum kit to edit.
3.Press [SET UP] to enter drum pad setting, and DRUM PAD SETTING contrast color.
11
4.Select pad via pad indication button or hit the pads.
5.Press [SET UP] again to enter tone parameter setting.
6. use direction key to select tone.
(Note:refer to the tone list for tone)
7.Use direction key to select VOLUME item.
8.Use direction key to change volume.
9. Use direction key to select PAN
10. Use direction key to change L/R Channel position.
(GM standard:000---127)
Change pad volume
Change pad L/R channel position
DRUM PAD SETTING
PAD TRIGGER
RELOAD FAC SET
EFFECT
DRUMRIM OPTION
VOICE=ESN_04
VOLUME=080
PAN=084
MIDI PITCH=044
Change pad voice

Edit and create owner’s drum kit
In the drum kit menu, user can change parameter according to the playing style then save it.
1.Press [KIT] to select the drum kit
2.Use the direction key to switch to the desired drum kit to edit.
3.Press [SET UP] to enter drum pad setting, and DRUM PAD SETTING contrast color.
11
4.Select pad via pad indication button or hit the pads.
5.Press [SET UP] again to enter tone parameter setting.
6. use direction key to select tone.
(Note:refer to the tone list for tone)
7.Use direction key to select VOLUME item.
8.Use direction key to change volume.
9. Use direction key to select PAN
10. Use direction key to change L/R Channel position.
(GM standard:000---127)
Change pad volume
Change pad L/R channel position
DRUM PAD SETTING
PAD TRIGGER
RELOAD FAC SET
EFFECT
DRUMRIM OPTION
VOICE=ESN_04
VOLUME=080
PAN=084
MIDI PITCH=044
Change pad voice
13. Press [SAVE] to save setting to user drum kit.
14. Use direction key to select user drum kit(01---12)
15. Press [SAVE] button to save
Save setting to user drum kit
12
11. Use direction key to select MIDI PITICH
12. Use direction key to change MIDI output pitch value(000---127)
(when adjusting parameter, press [SET UP] button to reset all parameters back to default status)
Change MIDI output pitch value
SAVE CHANGE
FOR USER01
PRESS SAVE FOR YES
PRESS CANCEL FOR NO

3. Use direction key to select trigger parameter.
4. Use direction key to change trigger parameter.
(Press direction key simultaneously, it goes back
the preset ）
CURVE 1:very low dynamic response, high volume. If used to trigger the pads,the curve is flat.
CURVE2: the standard setting, during playing or when volume changes, it generates maximum
natural signal.
CURVE3: compared to CURVE2, weak force generates relatively big change.
CURVE4: compared to CURVE2, strong force generates relatively big change.
CURVE5: compared to CURVE2, strong force generates very big change.
Adjust pad Trigger
1. Use the direction key to switch to PAD TRIGGER
2. Press [SET UP] to enter pad parameter setting. DRUM PAD SETTING
PAD TRIGGER
RELOAD FAC SET
EFFECT
DRUMRIM OPTION
Adjust pad curve
Pad curve is relative to the pad dynamic signal.
CURVE1 CURVE2
CURVE3 CURVE4 CURVE5
PAD HIHAT
PAD CURVE=3
THRSHLD=2
CROSSTALK=04
SENSITIVITY=08
MASK TIME=18
RETRIG CANCEL=10
13

3. Use direction key to select trigger parameter.
4. Use direction key to change trigger parameter.
(Press direction key simultaneously, it goes back
the preset ）
CURVE 1:very low dynamic response, high volume. If used to trigger the pads,the curve is flat.
CURVE2: the standard setting, during playing or when volume changes, it generates maximum
natural signal.
CURVE3: compared to CURVE2, weak force generates relatively big change.
CURVE4: compared to CURVE2, strong force generates relatively big change.
CURVE5: compared to CURVE2, strong force generates very big change.
Adjust pad Trigger
1. Use the direction key to switch to PAD TRIGGER
2. Press [SET UP] to enter pad parameter setting. DRUM PAD SETTING
PAD TRIGGER
RELOAD FAC SET
EFFECT
DRUMRIM OPTION
Adjust pad curve
Pad curve is relative to the pad dynamic signal.
CURVE1 CURVE2
CURVE3 CURVE4 CURVE5
PAD HIHAT
PAD CURVE=3
THRSHLD=2
CROSSTALK=04
SENSITIVITY=08
MASK TIME=18
RETRIG CANCEL=10
13
Note
If two close pads are hit at the same time and one pad threshold is too
high, the high threshold pad does not generate a signal, so take care to
set threshold to avoid crosstalk.
Eliminate pad crosstalk
When two pad are close, hitting one pad can cause the other pad generates a signal. This crosstalk
can be eliminate by setting a high parameter of the other pad.
14
Adjust pad threshold
threshold: the minimum force to trigger a pad signal.
Setting a high threshold, the pad needs a strong force to generate a signal. This can avoid accidental
response, e.g. other device or pad generate unnecessary signal.
Setting a low threshold, the pad needs a weak force to generate a signal.
User can adjust threshold based on external condition and performing style.
Threshold range:1---8
Adjust pad sensitivity
Sensitivity:1-16
Your can adjust the sensitivity of the pads to accommodate your personal playing style.
This allows you to have more dynamic control over the sound volume,based on how hard
you play.
Higher sensitivity allows the pad to produce a loud volume even when played softly.
Lower sensitivity will keep the pad producing a low volume even when played strongly.
(Press direction key simultaneously, it goes back the preset ）
Double Triggering Prevention(Mask Time)
Mask Time:0-64(ms)
This setting allow you to prevent double trigger
When playing a kick trigger the beater can bounce back and hit the head a second time
immediately after the intended note. This causes a single hit to “double trigger”(two sounds
instead of one).The Mask Time setting helps to prevent this. Once a pad has been hit, any
additional trigger signals occurring within the specified “Mask Time”(0-64 msec) will be
ignored.
When using a kick trigger, try to let the beater bounce back and hit the head very quickly, the
raise the “Mask Time” value until there are no more sounds made by the beater rebound.
Note:
1. When set to a high value , it will be difficult to play very quickly. Set this to as low a
value as you can
2. If two or more sounds are being produced when you strike the head just once, then
adjust Retrig Cancel.

Retrig Cancel: 01-16
This setting allow you to prevent re-trigger
(Re-trigger
Important if you are using acoustic drum triggers. Such triggers can produce altered
waveforms, which may also cause inadvertent sounding at Point A in the following figure
(Retrigger)
)
This occurs in particular at the decaying edge of the waveform. Retrigger Cancel detects
such distortion in and prevents retriggering from occurring.
While repeatedly striking the pad, raise the “Retrig Cancel”value until retriggering no longer
occurs.
NOTES:
1.Although setting this to a high value prevents retriggering, it then becomes
easy for sounds to be omitted whe the drums played fast (roll etc.). Set this
to the lowest value possible whie still ensuring that there is no retriggering.
2.You can also eliminate this problem of retriggering with the Mask Time setting.
Mask Time does not detect trigger signals if they occur within the specified
amount of time after the previous trigger signal was received. Retrigger
Cancel detects the attenuation of the trigger signal level, and triggers the
sound after internally determining which trigger signals were actually
generated when the head was struck, while weeding out the other false
trigger signals that need not trigger a sound.
15
SAVE PAD TRIGGER SETTING
After all PAD TRIGGER parameter has been set, you can save your setting.
Press SAVE to save setting
SAVE CURRENT
TRIGGER SETTING
PRESS SAVE FOR YES
PRESS CANCEL FOR NO

Retrig Cancel: 01-16
This setting allow you to prevent re-trigger
(Re-trigger
Important if you are using acoustic drum triggers. Such triggers can produce altered
waveforms, which may also cause inadvertent sounding at Point A in the following figure
(Retrigger)
)
This occurs in particular at the decaying edge of the waveform. Retrigger Cancel detects
such distortion in and prevents retriggering from occurring.
While repeatedly striking the pad, raise the “Retrig Cancel”value until retriggering no longer
occurs.
NOTES:
1.Although setting this to a high value prevents retriggering, it then becomes
easy for sounds to be omitted whe the drums played fast (roll etc.). Set this
to the lowest value possible whie still ensuring that there is no retriggering.
2.You can also eliminate this problem of retriggering with the Mask Time setting.
Mask Time does not detect trigger signals if they occur within the specified
amount of time after the previous trigger signal was received. Retrigger
Cancel detects the attenuation of the trigger signal level, and triggers the
sound after internally determining which trigger signals were actually
generated when the head was struck, while weeding out the other false
trigger signals that need not trigger a sound.
15
SAVE PAD TRIGGER SETTING
After all PAD TRIGGER parameter has been set, you can save your setting.
Press SAVE to save setting
SAVE CURRENT
TRIGGER SETTING
PRESS SAVE FOR YES
PRESS CANCEL FOR NO
Adjust pad effect
1. Use the direction key to switch to EFFECT
2. Press [SET UP] to enter pad effect setting.
EQ setting
3. Use the direction key to select EQ type.
4. Use the direction key to change EQ value.
HI GAIN=12(default) range:01---25
MID GAIN=18(default) range:01---25
LOW GAIN=20(default) range:01---25
DRUM PAD SETTING
PAD TRIGGER
RELOAD FAC SET
EFFECT
HI GAIN=12
MID GAIN=18
LOW GAIN=20
AMBIENCE=OFF
HI GAIN=12
MID GAIN=18
LOW GAIN=20
AMBIENCE=OFF
Ambience setting
5. Use the direction key to select AMBIENCE
6. Use the direction key to switch AMBIENCE
AMBIENCE=OFF
AMBIENCE=01
AMBIENCE=02
16

RELOAD SETTING
FOR USER01
SET UP FOR YES
CANCEL FOR NO
Reload to default setting
1. Use the direction key to select RELOAD FAC SET
2. press [SET UP] to go back to the default setting.
3. Use the direction key to select saved drum kit.
e.g. FOR USER01
4. Press [SET UP] to go back to the default setting
5. Press [CANCEL] to cancel the default setting
Drumrim option
1. Use the direction key to select Drumrim option
2. press [SET UP] to enter setting. Drumrim
3. Use the direction key to change option.
4.ON: one sound when hit the pad rim
OFF: no sound when hti the pad rim
PAD SENSITIVITY
RELOAD FAC SET
EFFECT
DRUMRIM OPTION
17