JustinTymeSports MINI PRO 1.0 User manual

MINI PRO 1.0 BASKETBALL HOOP
NOTE: Although the rim and backboard are very strong, they are NOT designed for hanging. The rim is designed to safely
flex 2” at the front of the rim. NEVER HANG ON THE RIM – THIS WILL VOID YOUR WARRANTY. DO NOT ADJUST
THE TENSION ON YOUR SPRING. Visit http://www.justintymesports.net/faq/ for full details of your warranty.
Mini Pro 1.0 Contents:
(1) Backboard Assembly
(1) Rim Assembly
(1) Net
(2) 1/4" x 1" x 12" Rubber Frame Pads
(1) Upper Bracket
(1) Mini Rubber Basketball
(2) #10-24 x 1/2" Frame Screws
(2) #10-24 Self Locking Nuts
(4) 1/4”-20 x 1" Rim Screws
(3) 1/4” x 2” Bracket Screws
(3) 1/4” Washers
Caring for your backboard:
Your backboard is made from polycarbonate which is known for its durability and break resistance. Wash your backboard
with mild soap and water. Use a clean soft cloth, applying only light pressure. Rinse with clear water and dry by blotting
with a damp cloth or chamois. Do not use window cleaning sprays, kitchen scouring compounds, or solvents.
Assembly Instructions:
These assembly instructions are for the Mini Pro 1.0 hoop set. To simplify assembly, the backboard and rim are pre-
assembled. You will need a Phillips head screwdriver, a 3/8" wrench or an adjustable wrench, a drill with 3/16” bit, a
pencil, and it is also recommended, but not necessary, you have stud finder and a level.
If you have questions during assembly, please contact us at 888-564-1082 or [e-mail]. You can
find video of the assembly process at http://www.justintymesports.net/installation
I. Upper Bracket
1. Install the Upper Bracket using (2) of the #10-24 x
1/2" Frame Screws and Locknuts.
Note: The Upper Bracket attaches to the inside of the
Frame. The tab of the bracket should point up, but you
may have it point down if you wish. This will adjust
measurements when you go to mount the hoop.
Figure 1

II. Rim and Bracket Assembly
2. Stand the Lower Bracket so the four small holes
are facing up. Align the lower bracket so the
holes on the tabs run vertically, one above
and one below the rim. Mounting the bracket
horizontally will substantially change the
intended forces on the hoop, not allow you to
dunk, and void your warranty. See Fig. 2 & 3
3. Carefully set the Backboard Assembly onto the
Lower Bracket while keeping the holes aligned.
4. Place the rim on the backboard and insert two of
the Rim Screws through the Rim and the
Backboard Assembly. Use a Phillips screwdriver
to turn the screws into the bracket so the rim is
secure. Do not tighten fully at this point.
5. Install the remaining two Rim Screws. Adjust
your rim so it is level when facing you. Tighten
the screws completely.
Figure 2
III. Net & Backboard Guards
6. Install the net on the eight metal eyelets on the
rim. The long loops should attach to the eyelets.
7. Install the (2) Rubber Backboard Guards on the
bottom of the Frame. Remove the paper backing
to expose the adhesive. Apply the pad starting at
the seam on the bottom of the frame. Continue
to align the pad to the frame as you work around
the corner of the frame.
Figure 3
IV. Mounting the Hoop
You will need a 3/16” drill and a 3/8” socket wrench. The
mounting bracket is designed to mount to a sturdy
structure such as a 2x4 stud in your wall - you should
locate the
center of the stud for the most secure mounting.
Drill two holes for the Lower Bracket and one hole for the
Upper Bracket. Mount using the three Bracket Screws and
Washers provided (screws are long enough to mount
through ½" drywall). You can use bar soap on the bracket
screws as a lubricant so the screws will turn in easier.
Note: The holes in the bottom bracket are 4" apart.
The distance from the top hole of the Lower Bracket to
the Upper Bracket hole is 9-9/16". If you have turned
your bracket sideways, these measurements will be
off (They will also be off if you have decided to turn
your upper bracket to face downward. Please turn
your bracket so the tabs run vertically and will mount
into one stud.
JustinTymeSports, LLC
Grand Rapids, MI 49548
www.justintymesports.net
© Copyright 2016