JVC KD-S13 User manual

1– EN
ENGLISH ESPAÑOL
INFORMATION (For U.S.A.)
This equipment has been tested and found to comply with the limits for a Class B di ital device, pursuant to Part 15 of
the FCC Rules. These limits are desi ned to provide reasonable protection a ainst harmful interference in a residential
installation. This equipment enerates, uses, and can radiate radio frequency ener y and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
uarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turnin the equipment off and on, the user is encoura ed to
try to correct the interference by one or more of the followin measures:
– Reorient or relocate the receivin antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Caution
Chan es or modifications not approved by JVC could void the user’s authority to operate the equipment.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicin to qualified
service personnel.
3. CAUTION: (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam.
(For Canada) Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical
instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
KD-S23/KD-S13
CD RECEIVER: INSTRUCTIONS
GET0400-001A
[J]
0706DTSMDTJEIN
EN
© 2006 Victor Company of Japan, Limited
For customer Use:
Enter below the Model No. and Serial No. which
are located on the top or bottom of the cabinet.
Retain this information for future reference.
Model No.
Serial No.
arning
If you need to operate the unit while drivin , be sure to
look ahead carefully or you may be involved in a traffic
accident.
Caution on volume setting
Discs produce very little noise compared with other sources.
Lower the volume before playin a disc to avoid dama in
the speakers by the sudden increase of the output level.
To keep discs clean
Wipe in a strai ht line from center of disc to
ed e. Do not use liquid cleaners, thinners, or
benzene.
To play new discs
Remove any rou h areas from the inner and
outer ed es of the disc.
MAINTENANCE
How to clean the connectors
Wipe the connectors with
a cotton swab or cloth
moistened with alcohol.
Moisture condensation
Moisture may condense on the lens inside the unit. Eject
the disc and leave the unit turned on for a few hours until
the moisture evaporates.
Do not use the following discs:
• CD-RWs may require a lon er readout time since the
reflectance of CD-RWs is lower than that of re ular CDs.
Playing an MP3/ MA disc (for KD-S23)
• This unit can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (re ardless of the
letter case—upper/lower).
• This unit can show the names of albums, artists
(performer), and ta (Version 1.0, 1.1, 2.2, 2.3, or 2.4) for
MP3 files and for WMA files.
• This unit can display only one-byte characters. No other
characters can be correctly displayed.
• This unit can play back MP3/WMA files meetin the
conditions below:
– Bit rate: 8 kbps — 320 kbps
– Samplin frequency:
48 kHz, 44.1 kHz, 32 kHz (for MPEG-1)
24 kHz, 22.05 kHz, 16 kHz (for MPEG-2)
– Disc format: ISO 9660 Level 1/ Level 2, Romeo, Joliet,
Windows lon file name
• The maximum number of characters for file/folder names
vary amon the disc format used (includes 4 extension
characters—<.mp3> or <.wma>).
– ISO 9660 Level 1: up to 12 characters; ISO 9660 Level
2: up to 31 characters; Romeo: up to 128 characters;
Joliet: up to 64 characters; Windows lon file name: up
to 128 characters
• This unit can play back files recorded in VBR (variable bit
rate).
Files recorded in VBR have a discrepancy in elapsed
time display, and do not show the actual elapsed time.
Especially, after performin the search function, this
difference becomes noticeable.
• This unit can reco nize a total of 512 files, of 200 folders,
and of 8 hierarchies.
• This unit cannot play back the followin files:
– MP3 files encoded with: MP3i and MP3 PRO format, in
an inappropriate format, layer 1/2.
– WMA files: encoded with lossless, professional, and
voice format; not based upon Windows Media® Audio;
copy-protected with DRM.
– Files which have the data such as WAVE, ATRAC3, etc.
• The search function works but search speed is not
constant.
Basic operations
• By pressin SOURCE on the unit, you can also turn on the
power. If the source is ready, playback also starts.
• If you turn off the power while listenin to a disc, disc
play will start from where playback has been stopped
previously, next time you turn on the power.
• When no disc is loaded in the unit, you cannot select
“DISC” as the playback source.
Tuner operations
• Durin SSM search...
– All previously stored stations are erased and stations
are stored newly.
– Received stations are preset in No. 1 (lowest
frequency) to No. 6 (hi hest frequency).
– When SSM is over, the station stored in No. 1 will be
automatically tuned in.
Disc operations
Caution for DualDisc playback
• The Non-DVD side of a “DualDisc” does not comply with
the “Compact Disc Di ital Audio” standard. Therefore, the
use of Non-DVD side of a DualDisc on this product may
not be recommended.
General
• KD-S13: This unit has been desi ned to reproduce CDs
and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD
(CD-DA) formats. KD-S23 can also play back CD Texts and
CD-Rs/CD-RWs in MP3/WMA formats.
Playing a CD-R or CD-R
• Use only “finalized” CD-Rs or CD-RWs.
• This unit can play back multi-session discs; however,
unclosed sessions will be skipped while playin .
• Some CD-Rs or CD-RWs may not play back on this unit:
– Discs are dirty or scratched.
– Moisture condensation occurs on the lens inside the
unit.
– The pickup lens inside the unit is dirty.
– CD-R/CD-RW on which the files are written with
“Packet Write” method.
– There are improper recordin conditions (missin data,
etc.) or media conditions (stain, scratch, warp, etc.).
MORE ABOUT THIS UNIT
For safety...
• Do not raise the volume level too much, as this will block
outside sounds, makin drivin dan erous.
• Stop the car before performin any complicated
operations.
Temperature inside the car...
If you have parked the car for a lon time in hot or cold
weather, wait until the temperature in the car becomes
normal before operatin the unit.
Connector
Warped disc Sticker Sticker residue Stick-on label
How to forcibly eject a disc
• If this does not work, reset
your unit.
• Be careful not to drop the
disc when it ejects.
Detaching the control panel
Attaching the control panel
How to reset your unit
Reset the unit after installation is complete.
KD-S23:
KD-S13:
• Your preset adjustments will also be erased.
• KD- 23: If a disc is loaded, it will eject. Be careful not to
drop the disc.
PREPARATIONS
Finish
Enter PSM menu.
Select an item.
Set/adjust.
Basic settings
Deactivate the display
demonstration.
Adjust the hour. Adjust the minute.
Cancel the display
demonstration
Set the clock
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understandin and to obtain the best
possible performance from the unit.
Installation/connection are explained at the last section of this manual (reverse page, indicated with
symbol).
Unusual shape Sin le CD (8 cm disc)
[European Union only]
EN_KD-S23_13[J]f.indd 1EN_KD-S23_13[J]f.indd 1 6/23/06 2:24:34 PM6/23/06 2:24:34 PM

2 – EN
INSTRUCTIONS
FM station automatic presetting —SSM (Strong-station Sequential Memory)
You can preset six stations for each band.
hen an FM stereo broadcast is hard to receive
General settings—PSM
Sound adjustments
Indication (For)
BAS
(bass)
TRE
(treble)
LOUD
(loudness)
USER (Flat sound) 00 00 OFF
ROCK (Rock or disco music) +03 +01 ON
CLASSIC (Classical music) +01 –02 OFF
POPS (Li ht music) +04 +01 OFF
HIP HOP (Funk or rap music) +02 00 ON
JAZZ (Jazz music) +02 +03 OFF
Adjusting the sound
BAS*2 (bass): Adjust the bass. –06 to +06
TRE*2 (treble): Adjust the treble. –06 to +06
FAD*3 (fader): Adjust the front and rear speaker balance. R06 to F06
BAL (balance): Adjust the left and ri ht speaker balance. L06 to R06
LOUD*2 (loudness): Boost low and hi h frequencies to
produce a well-balanced sound at low volume level.
LOUD ON or
LOUD OFF
SUB. (subwoofer): Adjust the subwoofer output level
when a subwoofer is connected.
00 to 08
VOL (volume): Adjust the volume. 00 to 30 (or 50)*4
*1 Displayed only when “L/O MODE” is set to “WOOFER.”
*2 When you adjust the bass, treble, or loudness, the adjustment you have made is
stored for the currently selected sound mode (C-EQ) including “U ER.”
*3 If you are using a two-speaker system, set the fader level to “00.”
*4 Depending on the amplifier gain control setting.
Preset values
Disc operations (MP3/ MA/CD Text discs are playable in KD-S23 only)
Insert disc. All tracks will be played repeatedly until
you chan e the source or eject the disc. Eject disc.
• [Press]: Go to the next or previous track.
• [Hold]: Fast-forwards or reverses the track.
• \ [Press]: Go to the next or previous
folders (for MP3/WMA discs).
• [Press]: Select track (for CD) or folder* (for MP3/WMA)
number (01 – 06).
• [Hold]: Select track (for CD) or folder* (for MP3/WMA)
number (07 – 12).
* Folders are required to assigned with 2-digit numbers at
the beginning.
Selecting the playback modes
After pressin , press the followin buttons to...
TRK RPT : Plays the current track
repeatedly.
FLDR RPT* : Plays all tracks of the current
folder repeatedly.
RPT OFF : Cancels.
FLDR RND* : Plays all tracks of the current
folder, then tracks of the next
folder at random.
DISC RND : Plays all tracks of the current
disc at random.
RND OFF : Cancels.
* Only for MP3/WMA.
Prohibiting disc ejection
You can lock a disc in the loadin slot.
To cancel the prohibition, repeat the same procedure.
Changing the display information
hile playing an audio CD or a CD Text
hile playing an MP3 or a MA disc
: Clock with the current track number
: Elapsed playin time with the current track number
*1 If the current disc is an audio CD, “NO NAME” appears.
*2 If an MP3/WMA file does not have tags or “TAG DI P” is
set to “TAG OFF,” folder name and file name appear.
OPERATIONS (MP3/WMA/CD Text discs are pla able in KD-S23 onl )
Basic operations
Select the source.
• Turn on the power.
• Turn off the power [Hold].
• Attenuate the sound (if the
power is on).
Volume control. Detach the panel.
Check the current clock time.
Control panel
Radio operations
Select preset station.
Manual presetting
Example: Storin FM station of 92.5 MHz into preset number 4 of the FM1 band.
Display window
Disc indicator
Playback mode / item indicator
• ST: Li hts up when receivin an FM
stereo broadcast with sufficient si nal
stren th.
• MO: Li hts up in monaural mode.
• Source display
• Volume level indicator
• Time countdown indicator
Main display (time,
playback information)
EQ (equalizer) indicator
Sound mode (C-EQ: custom equalizer)
indicator
LOUD (loudness) indicator
Disc type indicators
Disc information indicators
Tr (track) indicator
SETTINGS
Select an item.
Set/adjust.
Finish
Enter PSM menu.
Remote controller—RM-RK50 (supplied for KD-S23)
• Turns the power on if pressed briefly or
attenuates the sound when power is on.
• Turns the power off if pressed and held.
• Chan es the FM/AM bands with 5 U.
• Chan es the preset stations with D ∞.
• Chan es the folders of MP3/WMA discs.
• Adjusts the volume level.
• Selects the sound mode
(C-EQ: custom equalizer).
• Selects the source.
• Searches for stations if pressed briefly.
• Fast-forwards or reverses the track if
pressed and held.
• Chan es the tracks of the disc if pressed
briefly.
Select “FM/AM.”
Select the bands.
Search for a station—Auto Search.
Manual Search: Hold either one of the buttons until
“M” flashes on the display, then press it repeatedly.
Remote sensor (for KD-S23)
• DO NOT expose to strong
light.
Reception improves, but stereo effect will be lost.
• MO indicator li hts up.
To restore the stereo effect, repeat the same procedure.
7 Installing battery
arning: To prevent accidents and damage
• Do not install any battery other than CR2025 or its
equivalent.
• Store out of reach of children.
• Do not rechar e, short, or dismantle.
• Do not dispose of in fire.
• Do not carry around with other metallic materials.
Lithium coin battery (CR2025)
For USA-California Only: This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material—
special handlin may apply. See www.dtsc.ca. ov/hazardouswaste/perchlorate
7 Features
Example:
ee reverse page \
EN_KD-S23_13[J]f.indd 2EN_KD-S23_13[J]f.indd 2 6/23/06 2:24:38 PM6/23/06 2:24:38 PM

3 – EN
Audio amplifier section
Power Output:
17 W RMS × 4 Channels at 4 Ω and
≤ 1% THD+N
Si nal to Noise Ratio:
80 dBA (reference: 1 W into 4
Ω )
Load Impedance: 4
Ω (4 Ω to 8 Ω allowance)
Tone Control Ran e: Bass: ±10 dB at 100 Hz
Treble: ±10 dB at 10 kHz
Frequency Response: 40 Hz to 20 000 Hz
Line-Out Level/Impedance:
KD-S23: 2.5 V/20 k Ω load (full scale)
KD-S13: 2.0 V/20 k Ω load (full scale)
Output Impedance: 1 k Ω
Subwoofer-Out Level/Impedance: 2.0 V/20 kΩ load (full scale)
Prepare this before installation
Check the battery system in your car
PREPARATIONS
Symptoms Remedies/Causes
General
• Sound cannot be heard from the speakers. • Adjust the volume to the optimum level.
• Check the cords and connections.
• The buttons on the unit do not work as you
intended.
If you press M MODE, some buttons work differently from it
ori inal function. Wait for 5 seconds or press M MODE a ain.
• This unit does not work at all. Reset the unit.
FM/AM
• SSM automatic presettin does not work. Store stations manually.
• Static noise while listenin to the radio. Connect the antenna firmly.
Disc playback
• Disc ejects. Insert the disc correctly.
• CD-R/CD-RW cannot be played back.
• Tracks on the CD-R/CD-RW cannot be
skipped.
• Insert a finalized CD-R/CD-RW.
• Finalize the CD-R/CD-RW with the component which you used
for recordin .
• Disc can be neither played back nor ejected. • Unlock the disc.
• Eject the disc forcibly.
• Disc sound is sometimes interrupted. • Stop playback while drivin on rou h roads.
• Chan e the disc.
• Check the cords and connections.
• “NO DISC” appears on the display. Insert a playable disc into the loadin slot.
MP3/ MA playback (for KD-S23 only)
• Disc cannot be played back. • Use a disc with MP3/WMA tracks recorded in the format
compliant with ISO 9660 Level 1, Level 2, Romeo, or Joliet.
• Add the extension code <.mp3> or <.wma> to the file names.
• Noise is enerated. Skip to another track or chan e the disc. (Do not add the extension
code <.mp3> or <.wma> to non-MP3 or WMA tracks.)
• A lon er readout time is required (“CHECK”
keeps flashin on the display).
Do not use too many hierarchies and folders.
• Tracks do not play back in the order you
have intended them to play.
Playback order is determined when the files are recorded.
• Elapsed playin time is not correct. This sometimes occurs durin play. This is caused by how the
tracks are recorded on the disc.
• “NO FILES” appears on the display. Insert a disc that contains MP3/WMA tracks.
• Correct characters are not displayed (e. .
album name).
This unit can only display alphabets (upper case), numbers, and a
limited number of symbols.
Indication Item
( : Initial)
Setting
DEMO • DEMO ON
• DEMO OFF
: Display demonstration will be activated automatically if no operation is done
for about 20 seconds.
: Cancels.
CLOCK H (Hour) 1 – 12 : [Initial: 1 (1:00)]
CLOCK M (Minute) 00 – 59 : [Initial: 00 (1:00)]
DIMMER *1• ON
• OFF
: Dims the display illumination.
: Cancels.
SCROLL *1• ONCE
• AUTO
• OFF
: Scrolls the disc information once.
: Repeats scrollin (at 5-second intervals).
: Cancels.
• Pressin DISP for more than one second can scroll the display re ardless of the
settin .
OOFER *1, *2• LO
• MID
• HIGH
: Frequencies lower than 90 Hz are sent to the subwoofer.
: Frequencies lower than 135 Hz are sent to the subwoofer.
: Frequencies lower than 180 Hz are sent to the subwoofer.
L/O MODE • REAR
• OOFER
: Select if the REAR LINE OUT terminals are used for connectin the speakers
(throu h an external amplifier).
: Select if the REAR LINE OUT terminals are used for connectin a subwoofer.
TAG DISP *1• TAG ON
• TAG OFF
: Shows the ta while playin MP3/WMA tracks.
: Cancels.
AMP GAIN *3• LO P R
• HIGH P R
: VOL 00 – VOL 30 (Select if the maximum power of each speaker is less than
45 W to prevent the speaker from bein dama ed.)
: VOL 00 – VOL 50
AREA • AREA US
• AREA SA
• AREA EU
: When usin in North/Central/South America. AM/FM intervals are set to
10 kHz/200 kHz.
: When usin in South American countries where FM interval is 100 kHz. AM
interval is set to 10 kHz.
: When usin in any other areas. AM/FM intervals are set to 9 kHz/50 kHz
(100 kHz durin auto search).
*1 For KD- 23.
*2 Displayed only when “L/O MODE” is set to “WOOFER.”
*3 The volume level automatically changes to “VOL 30” if you change to “LOW PWR” while the volume level is set higher than
“VOL 30.”
You need the installation kits which corresponds to your car.
• Mark all the check boxes ( ) to make sure you have follow the instructions and the listed parts.
TROUBLESHOOTING
General
Power Requirement: Operatin Volta e: DC 14.4 V
(11 V to 16 V allowance)
Groundin System: Ne ative round
Allowable Operatin Temperature:
0°C to +40°C (32°F to 104°F)
Dimensions (W × H × D):
Installation Size (approx.):
182 mm × 52 mm × 150 mm
(7-3/16” × 2-1/16” × 5-15/16”)
Panel Size (approx.):
188 mm × 58 mm × 11 mm
(7-7/16” × 2-5/16” × 7/16”)
Mass (approx.):
1.2 kg (2.6 lbs) (excludin accessories)
Design and specifications are subject to change without
notice.
If a kit is necessary for your car, consult your telephone
directory for the nearest car audio speciality shop.
SPECIFICATIONS
I
Handles
E
Washer (ø5)
F
Lock nut (M5)
G
Mountin bolt—
M5 x 20 mm (M5 x 13/16")
H
Rubber cushion
A
Control panel
B
Sleeve
C
Trim plate
D
Power cord
12 V DC, NEGATIVE ground
• The fuse blows.
* Are the red and black leads connected correctly?
• Power cannot be turned on.
* Is the yellow lead connected?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Sound is distorted.
* Is the speaker output lead rounded?
* Are the “–” terminals of L and R speakers rounded in
common?
TROUBLESHOOTING
• Noise interfere with sounds.
* Is the rear round terminal connected to the car’s chassis
usin shorter and thicker cords?
• This unit becomes hot.
* Is the speaker output lead rounded?
* Are the “–” terminals of L and R speakers rounded in
common?
• This unit does not work at all.
* Have you reset your unit?
INSTRUCTIONS
Tuner section
Frequency Ran e:
FM: 87.5 MHz to 107.9 MHz
(with channel interval set to 100 kHz or 200 kHz)
87.5 MHz to 108.0 MHz
(with channel interval set to 50 kHz)
AM: 530 kHz to 1 710 kHz
(with channel interval set to 10 kHz)
531 kHz to 1 602 kHz
(with channel interval set to 9 kHz)
[FM Tuner]
Usable Sensitivity: 11.3 dBf (1.0 μV/75 Ω )
50 dB Quietin Sensitivity: 16.3 dBf (1.8 μV/75
Ω )
Alternate Channel Selectivity (400 kHz): 65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 35 dB
[AM Tuner]
Sensitivity: 20 μV
Selectivity: 35 dB
CD player section
Type: Compact disc player
Si nal Detection System: Non-contact optical pickup
(semiconductor laser)
Number of channels: 2 channels (stereo)
Frequency Response: 5 Hz to 20 000 Hz
Dynamic Ran e: 96 dB
Si nal-to-Noise Ratio: 98 dB
Wow and Flutter: Less than measurable limit
For KD-S23:
MP3 Decodin Format: MPEG1/2 Audio Layer 3
Max. Bit Rate: 320 kbps
WMA (Windows Media® Audio) Decodin Format:
Max. Bit Rate: 192 kbps
• Microsoft and Windows Media are either re istered
trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Having TROUBLE with operation?
Please reset your unit
Still having trouble??
Call 1-800-252-5722 (USA ONLY)
http://www.jvc.com
Parts list for installation and connection
J
Remote controller
K
Battery
For KD-S23
EN_KD-S23_13[J]f.indd 3EN_KD-S23_13[J]f.indd 3 6/16/06 5:43:58 PM6/16/06 5:43:58 PM

4 – EN
INSTALLATION / CONNECTION
When using the optional stay
Install the unit at an angle of
less than 30˚.
Screw (option)
Stay (option)
Fire wall
Dashboard
* Not supplied for this unit.
Flat type screws
— 5 × 8 mm ( 5 × 3/8")*
Pocket
Flat type screws
— 5 × 8 mm ( 5 × 3/8")*
Bracket*
Bracket*
Removing the unit
In dash-mounting
Before removing the unit, release the rear section.
When installing the unit without using the sleeve
In a Toyota car for example, first remove the car radio and install the unit in its place.
Do the required electrical
connections.
Bend the appropriate tabs
to hold the sleeve firmly
in place.
When you stand the unit, be careful
not to damage the fuse on the rear.
Purple
Front speaker (left)
To the remote lead of other
equipment or automatic antenna if
any (200 mA max.)
Blue with white
stripe
Red To an accessory terminal in
the fuse block
To a live terminal in the
fuse block connecting to the
car battery (bypassing the
ignition switch) (constant
12 V)
Yellow *2
To metallic body or
chassis of the car
Black
Ignition switch
*1 Not supplied for this unit.
*2 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot be
turned on.
*3 Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint (if
coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.
*4 ignal cord (not supplied for this unit)
15 A fuse
Fuse block
Rear speaker (left)
Rear speaker (right)
Front speaker (right)
White with black stripe
Line out
Rear ground terminal
Antenna
terminal
Set “L/O MODE” to “WOO ER”
(See “General settings—PSM.”)
You can also connect a subwoofer to the REAR
LINE OUT terminals.
Rear speakers
Remote lead
Remote lead (blue with white stripe)
To the remote lead of other equipment
or automatic antenna if any
Y-connector *1
Front speakers
Subwoofer
Set “L/O MODE” to “REAR”
(See “General settings—PSM.”)
You can connect a power amplifier for rear
speakers.
Gray with black stripe
Green
Gray
Green with black stripe
Purple with black stripe
White
JVC Amplifier
ELECTRICAL CONNECTIONS
Typical connections Connecting the external amplifier or subwoofer
INSTALLATION
If you are not sure how to install this unit correctly, consult your JVC car audio dealer.
ake sure to disconnect the battery’s negative terminal.
• Be sure to ground this unit to the car’s chassis again after installation.
Note:
It is recommended to connect to the speakers with maximum power of more than 45 W (both at the rear and at the front,
with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 45 W, change “A P GAIN” setting to prevent the
speakers from being damaged (see “General settings—PS ”). Heat sink
High
Connect only the front speakers if your
speaker system is two-speaker system.
PRECAUTIONS on power supply and speaker connections
JVC Amplifier
EN_KD-S23_13[J]f.indd 4EN_KD-S23_13[J]f.indd 4 6/16/06 5:53:14 PM6/16/06 5:53:14 PM