JVC KD-SR81BT User manual

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
ENGLISH
FRANÇAIS
ESPAÑOL
B5A-0191-00 [J]
KD-SR81BT
CD RECEIVER
INSTRUCTION MANUAL
RÉCEPTEUR CD
MANUEL D’INSTRUCTIONS
RECEPTOR CON CD
MANUAL DE INSTRUCCIONES
Please read all instructions carefully before
operation to obtain the best possible performance
from the unit.
Veuillez lires les instructions attentivement avant
d’utiliser l’appareil afin d’obtenir les meilleures
performances possibles de l’appareil.
Por favor lea detenidamente este manual para
comprender a fondo todas las instrucciones y
obtener un máximo disfrute de esta unidad.
For customer Use:
Enter below the Model No. and Serial No. which are
located on the top or bottom of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
JS_JVC_KD_SR81BT_J_C00.indd 1JS_JVC_KD_SR81BT_J_C00.indd 1 1/12/2015 8:32:29 AM1/12/2015 8:32:29 AM

i
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
CAUTION
Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
In compliance with Federal Regulations, following are reproductions of labels on, or inside
the product relating to laser product safety.
JVC KENWOOD Corporation
2967-3, ISHIKAWA-MACHI,
HACHIOJI-SHI, TOKYO, JAPAN
THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR
SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
Location : Top Plate
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications
to this equipment may cause harmful interference unless the modifications are expressly
approved in the instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
FCC NOTE
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment may
cause harmful interference to radio communications, if it is not installed and used in
accordance with the instructions. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CALIFORNIA, USA ONLY
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material—
special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
Información acerca de la eliminación de equipos eléctricos y electrónicos al final de
la vida útil (aplicable a los países que hayan adoptado sistemas independientes de
recogida de residuos)
Los productos con el símbolo de un contenedor con ruedas tachado no
podrán ser desechados como residuos domésticos. Los equipos eléctricos y
electrónicos al final de la vida útil, deberán ser reciclados en instalaciones
que puedan dar el tratamiento adecuado a estos productos y a sus
subproductos residuales correspondientes. Póngase en contacto con su
administración local para obtener información sobre el punto de recogida
más cercano. Un tratamiento correcto del reciclaje y la eliminación de
residuos ayuda a conservar los recursos y evita al mismo tiempo efectos
perjudiciales en la salud y el medio ambiente.
Informação sobre a eliminação de pilhas
Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada
ao revendedor ou entidade autorizada para que a mesma seja devolvida ao fabricante ou
importador.
A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos
naturais ao mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio
ambiente.
JS_JVC_KD_SR81BT_J_S00.indd iJS_JVC_KD_SR81BT_J_S00.indd i 1/12/2015 8:33:46 AM1/12/2015 8:33:46 AM

ii
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
CAUTION
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C
to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very
low levels of RF energy that it deemed to comply without maximum permissive exposure
evaluation (MPE). But it is desirable that it should be installed and operated keeping the
radiator at least 20cm or more away from person’s body (excluding extremities: hands,
wrists, feet and ankles).
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry
Canada. To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more
than that necessary for successful communication.
ATTENTION
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées
pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences
radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui
est considérée conforme sans évaluation de l’exposition maximale autorisée. Cependant,
cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre
le dispositif rayonnant et le corps (à l’exception des extrémités : mains, poignets, pieds et
chevilles).
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé
pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son
gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
l’intensité nécessaire à l’établissement d’une communication satisfaisante.
IC (Industry Canada) Notice
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
The term “IC: ” before the certification/ registration number only signifies that the Industry
Canada technical specification were met.
Note de IC (Industrie Canada)
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
L’expression “IC:” avant le numéro d’homologation/ enregistrement signifie seulement
que les specifications techniques d’Industrie Canada ont été respectées.
Para cumplimiento de la COFETEL:
“La operación de este equipo está sujeta a las siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y
(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda
causar su operación no deseada”
JS_JVC_KD_SR81BT_J_S00.indd iiJS_JVC_KD_SR81BT_J_S00.indd ii 1/12/2015 8:33:46 AM1/12/2015 8:33:46 AM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
2
CONTENTS BEFORE USE
Warning
Do not operate any function that takes your attention away from safe driving.
Caution
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of
the output level.
General:
• Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded
data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short
circuit.
• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to
evaporate.
Remote control (RM-RK52):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or
equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used
batteries promptly. If swallowed, contact a physician immediately.
BEFORE USE 2
BASICS 3
GETTING STARTED 4
CD / USB / iPod / ANDROID 5
RADIO 7
AUX 8
Pandora® 9
iHeartRadio® 10
BLUETOOTH® 11
AUDIO SETTINGS 17
DISPLAY SETTINGS 19
MORE INFORMATION 19
TROUBLESHOOTING 21
SPECIFICATIONS 24
INSTALLATION /
CONNECTION 26
How to read this manual
• Operations are explained mainly
using buttons on the faceplate.
• [
XX ] indicates the selected items.
•
( XX) indicates references are
available on the stated page.
Maintenance
Cleaning the unit: Wipe off dirt on the faceplate with a dry silicone or soft cloth.
Cleaning the connector: Detach the faceplate and clean the connector
gently with a cotton swab, being careful not to damage the connector.
Handling discs:
• Do not touch the recording surface of the disc.
• Do not stick tape etc. on the disc, or use a disc with tape stuck on it.
• Do not use any accessories for the disc.
• Clean from the center of the disc and move outward.
• Clean the disc with a dry silicone or soft cloth. Do not use any solvents.
• When removing discs from this unit, pull them out horizontally.
• Remove burrs from the center hole and disc edge before inserting a disc.
Connector (on the reverse
side of the faceplate)
JS_JVC_KD_SR81BT_J_EN_1=F.indd 2JS_JVC_KD_SR81BT_J_EN_1=F.indd 2 1/12/2015 8:33:59 AM1/12/2015 8:33:59 AM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
3
ENGLISH
BASICS
To On the faceplate On the remote control
Turn on the power Press .
• Press and hold to turn off the power. —
Adjust the volume Turn the volume knob. Press or .
Press the volume knob to mute the sound or pause playback.
• Press again to cancel. Press to mute the sound or pause playback.
• Press again to cancel.
Select a source • Press repeatedly.
• Press , then turn the volume knob within 2 seconds.
Press SOURCE repeatedly.
Change the display
information
Press repeatedly.
( 21)
—
Attach
How to reset
Detach
Your preset adjustments
will also be erased.
Remote control (RM-RK52)Faceplate
Volume knob
(turn/press) Loading slot
Detach button
Display window
How to replace the battery
Pull out the insulation sheet
when using for the first time.
Remote sensor (Do not expose
to bright sunlight.)
JS_JVC_KD_SR81BT_J_EN_1=F.indd 3JS_JVC_KD_SR81BT_J_EN_1=F.indd 3 1/12/2015 8:34:00 AM1/12/2015 8:34:00 AM

4
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
GETTING STARTED
Cancel the demonstration
1 Press and hold .
2 Turn the volume knob to select [ DEMO ], then press the knob.
3 Turn the volume knob to select [ DEMO OFF ], then press the knob.
4 Press to exit.
Set the clock
1 Press and hold .
2 Turn the volume knob to select [ CLOCK ], then press the knob.
3 Turn the volume knob to select [ CLOCK SET ], then press the knob.
4 Turn the volume knob to make the settings, then press the knob.
Day Hour Minute
5 Turn the volume knob to select [ 24H/ 12H ], then press the knob.
6 Turn the volume knob to select [ 12 HOUR ] or [ 24 HOUR ], then press the
knob.
7 Press to exit.
To return to the previous setting item, press .
Set the basic settings
1 Press and hold .
2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Repeat step 2until the desired item is selected or activated.
4 Press to exit.
To return to the previous setting item, press .
1
2
Default: XX
SETTINGS
BEEP ON
:Activates the keypress tone.; OFF :Deactivates.
SRC SELECT
AM
* ON :Enables AM in source selection.; OFF :Disables.
PANDORA * ON :Enables PANDORA in source selection.; OFF :Disables.
IHEART * ON :Enables IHEARTRADIO in source selection.; OFF :Disables.
AUX * ON :Enables AUX in source selection.; OFF :Disables.
F/W UPDATE
SYSTEM / BLUETOOTH
F/W xxxx YES
:Starts upgrading the firmware.; NO :Cancels (upgrading is not
activated).
For details on how to update the firmware, see:
<http://www.jvc.net/cs/car/>.
CLOCK
CLOCK SYNC AUTO
:The clock time is automatically set using the Clock Time (CT) data
in FM Radio Broadcast Data System signal.;
OFF :Cancels.
CLOCK DISP ON :The clock time is shown on the display even when the unit is turned
off.;
OFF :Cancels.
* Not displayed when the corresponding source is selected.
3
JS_JVC_KD_SR81BT_J_EN_1=F.indd 4JS_JVC_KD_SR81BT_J_EN_1=F.indd 4 1/12/2015 8:34:02 AM1/12/2015 8:34:02 AM

ENGLISH 5
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
CD / USB / iPod / ANDROID
To On the faceplate On the remote control
Reverse / Fast-forward*3Press and hold . Press and hold .
Select a track/file Press .Press .
Select a folder*4Press . Press .
Repeat play*5Press repeatedly.
TRACK RPT / RPT OFF : Audio CD or JVC Playlist Creator (JPC) /
JVC Music Control (JMC) file
( 20)
TRACK RPT
/ FOLDER RPT / RPT OFF : MP3/WMA/AAC/WAV file
ONE RPT / ALL RPT / RPT OFF : iPod or ANDROID
Random play*5Press repeatedly.
ALL RND / RND OFF : Audio CD
FOLDER RND / ALL RND / RND OFF : MP3/WMA/AAC/WAV file or JPC / JMC
file
SONG RND / ALL RND / RND OFF : iPod or ANDROID
*1
Do not leave the cable inside the car when not using.
*2
When connecting an Android device, “Press [VIEW] to install JVC MUSIC PLAY APP” is shown. Follow the instructions to install the
application. You can also install the latest version of JVC MUSIC PLAY application on your Android device before connecting.
(
20 )
*3
For ANDROID: Applicable only when [ AUTO MODE ] is selected. ( 6)
*4
For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ ANDROID.
*5
For iPod/ ANDROID: Applicable only when [ HEAD MODE ]/ [ AUTO MODE ] is selected. ( 6)
Start playback
The source changes automatically and
playback starts.
CD
Eject disc Label side
USB input terminal
USB 2.0 cable
*1
(commercially available)
Micro USB 2.0 cable
*1
(commercially available)
(Accessory of the iPod/
iPhone)*
1
USB
iPod/iPhone
ANDROID*2
JS_JVC_KD_SR81BT_J_EN_1=F.indd 5JS_JVC_KD_SR81BT_J_EN_1=F.indd 5 1/12/2015 8:34:03 AM1/12/2015 8:34:03 AM

6
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
To On the faceplate
Select control
mode
While in iPod source, press repeatedly.
HEAD MODE : Control from the unit.
IPHONE MODE : Control from the iPod/iPhone. However, you
can still play/pause or file skip from the unit.
While in ANDROID source, press
repeatedly.
AUTO MODE : Control from the unit (using JVC MUSIC
PLAY application).
AUDIO MODE : Control other media player applications
from the Android device (without using JVC
MUSIC PLAY application). However, you can
still play/pause or file skip from the unit.
Select music
drive
Press repeatedly.
The stored songs in the following start playback.
• Selected internal or external memory of a smartphone
(Mass Storage Class).
• Selected drive of a multiple drives device.
Change the playback speed of the Audiobook
While listening to the iPod and [ HEAD MODE ] is selected ( Select control mode) ....
1 Press and hold .
2 Turn the volume knob to select [ IPOD ], then press the knob.
3 Press the volume knob to select [ AUDIOBOOKS ].
4 Turn the volume knob to make a selection, then press the knob.
0.5× SPEED / 1× SPEED / 2× SPEED : Select the desired playback speed of the
Audiobooks sound file in your iPod/iPhone.
(Default: Depends on your iPod/iPhone setting.)
5 Press to exit.
To return to the previous setting item, press .
Select a file from a folder/list
1 Press .
2 Turn the volume knob to select a folder/list, then press the
knob.
3 Turn the volume knob to select a file, then press the knob.
Quick Search
If you have many files, you can search through them quickly.
For MP3/WMA /AAC/WAV or JPC / JMC file:
Turn the volume knob quickly.
For iPod:
You can search for a file according to the first character.
Press or turn the volume knob quickly to select the
desired character (A to Z/ 0to9/ OTHERS).
• Select “OTHERS” if the first character is other than Ato Z,
0 to 9.
• To return to the previous setting item, press .
• To cancel, press and hold .
• For iPod, applicable only when [
HEAD MODE ] is selected. (  Select
control mode
)
• For ANDROID, applicable only when [
AUTO MODE ] is selected.
(
Select control mode )
CD / USB / iPod / ANDROID
JS_JVC_KD_SR81BT_J_EN_1=F.indd 6JS_JVC_KD_SR81BT_J_EN_1=F.indd 6 1/12/2015 8:34:04 AM1/12/2015 8:34:04 AM

ENGLISH 7
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
RADIO
“ST” lights up when receiving an FM stereo broadcast with sufficient
signal strength.
Search for a station
1 Press repeatedly to select FM or AM.
2 Press (or press on RM-RK52) to search for a station
automatically.
(or)
Press and hold (or press and hold on RM-RK52) until
“M” flashes, then press repeatedly to search for a station manually.
Settings in memory
You can store up to 18 stations for FM and 6 stations for AM.
Store a station
While listening to a station....
Press and hold one of the number buttons (1to 6).
(or)
1 Press and hold the volume knob until “PRESETMODE” flashes.
2 Turn the volume knob to select a preset number, then press the
knob.
The preset number flashes and “MEMORY” appears.
Select a stored station
Press one of the number buttons (1to6).
(or)
1 Press
2 Turn the volume knob to select a preset number, then press the
knob to confirm.
Other settings
1 Press and hold .
2 Turn the volume knob to select [ TUNER ], then press the knob.
3 Turn the volume knob to make a selection ( see the following table ) ,
then press the knob.
4 Repeat step 3until the desired item is selected/activated or follow
the instructions stated on the selected item.
5 Press to exit.
To return to the previous setting item, press .
Default:
XX
RADIO TIMER Turns on the radio at a specific time regardless of the current source.
1 ONCE / DAILY / WEEKLY / OFF :Select how often the timer will be
turned on.
2 FM / AM :Select the FM or AM band.
3 01 to 18 (for FM)/ 01 to 06 (for AM):Select the preset station.
4 Set the activation day* and time.
“
M ” lights up when complete.
Radio Timer will not activate for the following cases.
• The unit is turned off.
• [
OFF ] is selected for [ AM ] in [ SRC SELECT ] after Radio Timer for AM is
selected. (
4 )
* Selectable only when [
ONCE ] or [ WEEKLY ] is selected in step 1 .
JS_JVC_KD_SR81BT_J_EN_1=F.indd 7JS_JVC_KD_SR81BT_J_EN_1=F.indd 7 1/12/2015 8:34:05 AM1/12/2015 8:34:05 AM

8
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
RADIO
Use a portable audio player
1 Connect a portable audio player (commercially available).
2 Select [ ON ] for [ AUX ] in [ SRC SELECT ]. ( 4)
3 Press repeatedly to select AUX.
4 Turn on the portable audio player and start playback.
Use a 3-core plug head stereo mini plug for optimum audio
output.
3.5mm (1/8") stereo mini plug with “L” shaped connector
(commercially available)
Portable audio player
Auxiliary input jack
AUX
Default: XX
SSM SSM 01 – 06 / SSM 07 – 12 / SSM 13 – 18 :Automatically presets up
to 18 stations for FM. “SSM” stops flashing when the first 6 stations are
stored. Select
SSM 07 – 12 / SSM 13 – 18 to store the following 12
stations.
IF BAND AUTO :Increases the tuner selectivity to reduce interference noises from
adjacent FM stations. (Stereo effect may be lost.);
WIDE :Subjects to
interference noises from adjacent FM stations, but sound quality will not
be degraded and the stereo effect will remain.
MONO Displayed only when the source is FM.
ON :Improves the FM reception, but the stereo effect will be lost.;
OFF :Cancels.
AREA AREA US : For North/Central/South America, AM/FM intervals:
10kHz/200kHz.;
AREA SA :For some South American countries, AM/
FM intervals: 10kHz/50kHz.;
AREA EU :For any other areas, AM/FM
intervals: 9kHz/50kHz.
PTY SEARCH * Select a PTY code (see below).
If there is a station broadcasting a program of the same PTY code as you
have selected, that station is tuned in.
PTY code : NEWS , INFORM (information), SPORTS , TALK , ROCK , CLS ROCK (classic
rock),
ADLT HIT (adult hits), SOFT RCK (softrock), TOP 40 , COUNTRY , OLDIES , SOFT ,
NOSTALGA (nostalgia), JAZZ , CLASSICL (classical), R & B (rhythm and blues),
SOFT R&B (soft rhythm and blues), LANGUAGE , REL MUSC (religious music),
REL TALK (religious talk), PERSNLTY (personality), PUBLIC , COLLEGE , HABL ESP
(Spanish talk),
MUSC ESP (Spanish music), HIP HOP , WEATHER
* Only for FM source.
JS_JVC_KD_SR81BT_J_EN_1=F.indd 8JS_JVC_KD_SR81BT_J_EN_1=F.indd 8 1/12/2015 8:34:06 AM1/12/2015 8:34:06 AM

ENGLISH 9
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Pandora®
Preparation:
Install the latest version of the Pandora application on your device
(iPhone/ iPod touch), then create an account and log in to Pandora.
• Select [
ON ] for [ PANDORA ] in [ SRC SELECT ]. ( 4)
Start listening
1 Open the Pandora application on your device.
2 Connect your device to the USB input terminal.
The source changes to PANDORA and broadcast starts.
To On the faceplate On the remote control
Playback / pause Press the volume knob. Press .
Skip a track Press T. Press I.
Thumbs up or
thumbs down*2
Press . Press .
*1
Do not leave the cable inside the car when not using.
*2
If thumbs down is selected, the current track is skipped.
Create and save a new station
1 Press .
2 Turn the volume knob to select [ NEW STATION ], then press the knob.
3 Turn the volume knob to select [ FROM TRACK ] or [ FROM ARTIST ], then
press the knob.
A new station is created based on the current song or artist.
4 Press and hold number button 1, 4, 5or 6to store.
To select a stored station, press number button 1, 4, 5or 6.
Search for a registered station
1 Press .
2 Turn the volume knob to make a selection, then press the knob.
[
BY DATE ]: According to the registered date.
[
A-Z ]: Alphabetical order.
3 Turn the volume knob to the desired station, then press the knob.
To cancel, press and hold .
Bookmark a song or artist information
1 Press and hold the volume knob.
2 Turn the volume knob to make a selection, then press the knob.
[
THIS TRACK ]: Current song information
[
THIS ARTIST ]: Current artist information
“BOOKMARKED” appears and the information is stored to your device.
The bookmark is available on your Pandora account but not on this
unit.
USB input terminal
(Accessory of the iPod/iPhone)
*1
JS_JVC_KD_SR81BT_J_EN_1=F.indd 9JS_JVC_KD_SR81BT_J_EN_1=F.indd 9 1/12/2015 8:34:06 AM1/12/2015 8:34:06 AM

10
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
iHeartRadio®
Preparation:
Install the latest version of iHeart Link for JVC application on your device (iPhone/ iPod
touch), then create an account and log in to iHeartRadio.
• Select [
ON ] for [ IHEART ] in [ SRC SELECT ]. ( 4)
Start listening
1 Open the iHeart Link application on your device.
2 Connect your device to the USB input terminal.
3 Press repeatedly to select IHEARTRADIO.
Broadcast starts automatically
To On the faceplate On the remote control
Playback / pause Press the volume knob. Press .
Skip a track for custom station Press T. Press I.
Thumbs up or thumbs down
for custom station*2
Press . Press .
Create a new/custom station Press and hold the volume
knob.
—
Add to favorite stations for live
station
Press 1.—
Scan for live station Press 4.—
*1
Do not leave the cable inside the car when not using.
*2
If thumbs down is selected, the current track is skipped.
Search for a station
1 Press .
2 Turn the volume knob to select a category, then
press the knob.
3 Turn the volume knob to the desired station, then
press the knob.
When a city list appears, you can skip cities in
alphabetical order.
To cancel, press and hold .
Skip cities by alphabetical order
While a city list appears during search...
1 Turn the volume knob quickly to enter character
search.
You can search through the list quickly according to
the first character (A to Z).
2 Turn the volume knob or press to select the
character to be search for.
3 Press the volume knob to start searching.
To cancel, press and hold .
USB input terminal
(Accessory of the iPod/iPhone)
*1
JS_JVC_KD_SR81BT_J_EN_1=F.indd 10JS_JVC_KD_SR81BT_J_EN_1=F.indd 10 1/12/2015 8:34:07 AM1/12/2015 8:34:07 AM

ENGLISH 11
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Pair a Bluetooth device
When connecting a Bluetooth device to the unit for the first time, perform pairing between the unit
and the device.
1 Press to turn on the unit.
2 Search and select “JVC UNIT” on the Bluetooth device.
“BTPAIRING” flashes on the display.
• For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN)
code immediately after searching.
• Refer also to the manual supplied with your Bluetooth device.
3 Perform (A) or (B) depending on what scrolls on the display.
For some Bluetooth devices, pairing sequence may vary from the steps described below.
(A) “[Device Name]” “XXXXXX” “VOL–YES” “BACK–NO”
“XXXXXX” is a 6-digit passkey randomly generated during each pairing.
Ensure that the passkey which appears on the unit and Bluetooth device is the same.
Press the volume knob to confirm the passkey.
Operate the Bluetooth device to confirm the passkey.
(B) “[Device Name]” “VOL–YES” “BACK–NO”
Press the volume knob to start pairing.
• If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the
Bluetooth device.
You can change to a desired PIN code before pairing. (
15 )
• If only “PAIRING” appears, operate the Bluetooth device to confirm pairing.
“PAIRING COMPLETED” appears when pairing is completed and “ ” will light up when the Bluetooth
connection is established.
• Up to five devices can be registered (paired) in total.
• Only one Bluetooth device can be connected at any time.
• This unit supports Secure Simple Pairing (SSP).
• Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device
to the unit manually. Refer to the instruction manual of the Bluetooth device for more information.
• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you
reset the unit. To delete the paired device,
15 , [ DELETE PAIR ].
• When you connect iPhone/ iPod touch/ Android device to the USB input terminal, pairing request
(via Bluetooth) is automatically activated. Press the volume knob to pair once you have confirmed
the device name.
Automatic pairing request is activated only if:
– Bluetooth function of the connected devcie is turned on.
– [
AUTO CNNCT ] is set to [ ON ]. ( 15 )
– JVC MUSIC PLAY application is installed on the Android device.
BLUETOOTH®
BLUETOOTH — Connection
Supported Bluetooth profiles
– Hands-Free Profile (HFP)
– Serial Port Profile (SPP)
– Phonebook Access Profile (PBAP)
– Advanced Audio Distribution Profile (A2DP)
– Audio/Video Remote Control Profile (AVRCP)
Supported Bluetooth codecs
– Sub Band Codec (SBC)
– Advanced Audio Coding (AAC)
Connect the microphone
Adjust the microphone
angle
Secure using cord clamps
(not supplied) if necessary.
Microphone input jack
Microphone
(supplied)
Rear panel
JS_JVC_KD_SR81BT_J_EN_1=F.indd 11JS_JVC_KD_SR81BT_J_EN_1=F.indd 11 1/14/2015 10:17:57 AM1/14/2015 10:17:57 AM

12
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH — Mobile phone
Receive a call
When there is an incoming call:
– All the buttons flash.
– The unit answers the call automatically if [
AUTO ANSWER ] is set to a selected time. (  13 )
During a call:
– If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.
To On the faceplate On the remote control
Answer a call Press or the volume knob. Press .
Reject a call Press and hold or the volume
knob.
Press and hold .
End a call Press and hold or the volume
knob.
Press and hold .
Adjust the phone volume
[
00 ] to [ 50 ] (Default: [ 15 ]*)
Turn the volume knob during a call.
• This adjustment will not affect the
volume of the other sources.
—
Switch between hands-
free and private talk
modes
Press the volume knob during a call.
• Operations may vary according to the
connected Bluetooth mobile phone.
—
* Not applicable for iPhone. During a call, the unit synchronizes the phone volume on the iPhone to the unit.
Improve the voice quality
While talking on the phone....
1 Press and hold .
2 Turn the volume knob to make a selection
( see the following table ) , then press the
knob.
3 Repeat step 2until the desired item is
selected or activated.
4 Press to exit.
To return to the previous setting item, press
.
Default:
XX
MIC LEVEL –10
— +10 ( –4 ):The sensitivity of
the microphone increases as the number
increased.
NOISE RDCT –5 — +5 ( 0 ):Adjust the noise reduction
level until the least noise is being heard
during a phone conversation.
ECHO CANCEL –5 — +5 ( 0 ):Adjust the echo
cancellation delay time until the least
echo is being heard during a phone
conversation.
BLUETOOTH®
JS_JVC_KD_SR81BT_J_EN_1=F.indd 12JS_JVC_KD_SR81BT_J_EN_1=F.indd 12 1/12/2015 8:34:08 AM1/12/2015 8:34:08 AM

ENGLISH 13
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Make a call
You can make a call from the call history, phonebook, or dialing the number. Call by voice is also
possible if your mobile phone has the feature.
1 Press to enter Bluetooth mode.
2 Turn the volume knob to make a selection (see the following table), then press the knob.
3 Repeat step 2until the desired item is selected/activated or follow the instructions stated on
the selected item.
To return to the previous setting item, press .
RECENT CALL
1 Press the volume knob to select a name or a phone number.
• “>” indicates call received, “<“ indicates call made, “M” indicates call missed.
• “NO HISTORY” appears if there is no recorded call history or call number.
2 Press the volume knob to call.
PHONEBOOK
1 Press to select the desired letter (A to Z, 0to9, and OTHERS).
• “OTHERS” appears if the first character is other than Ato Z, 0 to 9.
2 Turn the volume knob to select a name, then press the knob.
3 Turn the volume knob to select a phone number, then press the knob to call.
• If the phone supports PBAP, the phonebook of the connected phone is automatically transferred to the
unit when pairing.
• This unit can display only non-accent letters. (Accent letters such as “Ú” is showns as “U”.)
Make the settings for receiving a call
1 Press to enter Bluetooth mode.
2 Turn the volume knob to make a selection
(see the following table), then press the
knob.
3 Repeat step 2until the desired item is
selected or activated.
To return to the previous setting item, press
.
Default:
XX
SETTINGS
AUTO ANSWER 01 SEC
— 30 SEC :The unit answers
incoming call automatically in
the selected time (in seconds).;
OFF :Cancels.
BLUETOOTH®
JS_JVC_KD_SR81BT_J_EN_1=F.indd 13JS_JVC_KD_SR81BT_J_EN_1=F.indd 13 1/12/2015 8:34:09 AM1/12/2015 8:34:09 AM

14
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
DIAL NUMBER 1 Turn the volume knob to select a number (0 to 9) or character ( , #,
+).
2 Press to move the entry position.
Repeat steps
1 and 2 until you finish entering the phone number.
3 Press the volume knob to call.
VOICE Speak the name of the contact you want to call or the voice command to
control the phone functions.
(  Make a call using voice recognition )
Make a call using voice recognition
1 Press and hold to activate the connected phone.
2 Speak the name of the contact you want to call or the voice
command to control the phone functions.
• Supported Voice Recognition features vary for each phone. Refer to the
instruction manual of the connected phone for details.
• This unit also supports the intelligent personal assistant function of
iPhone.
Delete a contact
1 Press to enter Bluetooth mode.
2 Turn the volume knob to select [ RECENT CALL ], then press the knob.
3 Turn the volume knob to select a contact.
4 Press and hold to enter delete mode.
5 Turn the volume knob to select [ DELETE ] or [ DELETE ALL ], then press
the knob.
DELETE : Selected name or phone number in step 3is deleted.
DELETE ALL : All names or phone numbers in [ RECENT CALL ]in step 2is
deleted.
6 Turn the volume knob to select [ YES ], then press the knob.
• To return to the previous setting item, press .
• Not applicable for mobile phone that supports PBAP.
BLUETOOTH®
Settings in memory
Store a contact in memory
You can store up to 6 contacts into the number buttons (1to 6).
1 Press to enter Bluetooth mode.
2 Turn the volume knob to select [ RECENT CALL ], [ PHONEBOOK ], or
[
DIAL NUMBER ], then press the knob.
3 Turn the volume knob to select a contact or enter a phone number.
If a contact is selected, press the volume knob to show the phone
number.
4 Press and hold one of the number buttons (1to 6).
“MEMORY P(selected preset number)” appears when the contact is
stored.
To erase a contact from the preset memory, select [
DIAL NUMBER ] in step 2
and store a blank number.
Make a call from memory
1 Press to enter Bluetooth mode.
2 Press one of the number buttons (1to 6).
3 Press the volume knob to call.
“NO PRESET” appears if there is no contacts stored.
Bluetooth mode settings
1 Press and hold .
2 Turn the volume knob to select [ BLUETOOTH ], then press the knob.
3 Turn the volume knob to make a selection ( 15) , then press the
knob.
4 Repeat step 3until the desired item is selected/activated or follow
the instructions stated on the selected item.
5 Press to exit.
To return to the previous setting item, press .
JS_JVC_KD_SR81BT_J_EN_1=F.indd 14JS_JVC_KD_SR81BT_J_EN_1=F.indd 14 1/12/2015 8:34:10 AM1/12/2015 8:34:10 AM

ENGLISH 15
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
Bluetooth compatibility check mode
You can check the connectivity of the supported profile between the
Bluetooth device and the unit.
• Make sure there is no Bluetooth device paired.
1 Press and hold .
“BLUETOOTH” “CHECK MODE” appears. “SEARCH NOW USING
PHONE” “PIN IS 0000” scrolls on the display.
2 Search and select “JVC UNIT” on the Bluetooth device within
3minutes.
3 Perform (A), (B) or (C) depending on what appears on the display.
(A) “PAIRING” “XXXXXX” (6-digit passkey): Ensure that the same
passkey appears on the unit and Bluetooth device, then operate
the Bluetooth device to confirm the passkey.
(B) “PAIRING” “PIN IS 0000”: Enter “0000” on the Bluetooth device.
(C) “PAIRING”: Operate the Bluetooth device to confirm pairing.
After pairing is successful, “PAIRING OK” “[Device Name]” appears and
Bluetooth compatibility check starts.
If “CONNECT NOW USING PHONE” appears, operate the Bluetooth device
to allow phonebook access to continue.
The connectivity result flashes on the display.
“PAIRING OK” and/or “H.FREE OK”*1and/or “A.STREAM OK”*2and/or
“PBAP OK”*3: Compatible
*1
Compatible with Hands-Free Profile (HFP)
*2
Compatible with Advanced Audio Distribution Profile (A2DP)
*3
Compatible with Phonebook Access profile (PBAP)
After 30 seconds, “PAIRING DELETED” appears to indicate that pairing has
been deleted, and the unit exits check mode.
• To cancel, press and hold to turn off the power, then turn
on the power again.
Default: XX
PHONE *1 Selects the phone or audio device to connect or disconnect.
“” appears in front of the device name when connected.
AUDIO *1
APPLICATION *1 Shows the connected phone name using the JVC Smart Music Control * 2
app. “ ” appears in front of the device name when connected.
DELETE PAIR 1 Turn the volume knob to select a device to delete, then press the
knob.
2 Turn the volume knob to select [ YES ] or [ NO ], then press the knob.
SET PINCODE
(0000)
Changes the PIN code (up to 6 digits).
1 Turn the volume knob to select a number.
2 Press to move the entry position.
Repeat steps
1 and 2 until you finish entering the PIN code.
3 Press the volume knob to confirm.
AUTO CNNCT ON :The unit automatically reconnect when the last connected
Bluetooth device is within range.;
OFF :Cancels.
AUTO PAIR ON :The unit automatically pair supported Bluetooth device (iPhone/
iPod touch/ Android device) when it is connected through USB input
terminal.Depending on the operating system of the connected device,
this function may not work. ;
OFF :Cancels.
INITIALIZE YES :Initializes all the Bluetooth settings (including stored pairing,
phonebook, and etc.).;
NO :Cancels.
INFORMATION MY  BT  NAME : Displays the unit name (JVCUNIT).;
MY  ADDRESS : Shows address of this unit.
*1
You can only connect another Bluetooth device by disconnecting the connected Bluetooth
device first. “ ” disappears when disconnected.
*2
JVC Smart Music Control is designed to view JVC car receiver status and perform simple
control operations on Android smart phones.
For JVC Smart Music Control operations, visit JVC website: <http://www.jvc.net/cs/car/>.
JS_JVC_KD_SR81BT_J_EN_1=F.indd 15JS_JVC_KD_SR81BT_J_EN_1=F.indd 15 1/12/2015 8:34:10 AM1/12/2015 8:34:10 AM

16
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
Internet radio via Bluetooth
Listen to Pandora
Preparation:
Select [
ON ] for [ PANDORA ] in [ SRC SELECT ]. ( 4)
You can listen to Pandora on your smart phone
(Android OS) through Bluetooth on this unit.
1 Open the Pandora application on your device.
2 Connect your Bluetooth audio player via
Bluetooth connection. ( 
11 )
3 Press repeatedly to select PANDORA.
The source switches and broadcast starts
automatically.
You can operate Pandora in the same way as Pandora
for iPod/iPhone. ( 
9 )
Listen to iHeartRadio
Preparation:
Select [
ON ] for [ IHEART ] in [ SRC SELECT ]. ( 4)
You can listen to iHeartRadio on your smart phone
(Android OS) through Bluetooth on this unit.
1 Open the iHeart Link application on your smart
phone.
2 Connect your smart phone via Bluetooth
connection. (
11 )
3 Press repeatedly to select
IHEARTRADIO.
The source switches and broadcast starts
automatically.
You can operate iHeartRadio in the same way as
iHeartRadio for iPod/iPhone. ( 
10 )
BLUETOOTH — Audio
Audio player via Bluetooth
1 Press repeatedly to select BTAUDIO (or press SOURCE on RM-RK52).
2 Operate the Bluetooth audio player to start playback.
To On the faceplate On the remote control
Playback / pause Press .Press .
Select group or folder Press . Press .
Reverse /
Forward skip
Press .Press .
Reverse / Fast-forward Press and hold .Press and hold .
Repeat play Press repeatedly.
TRACK RPT , ALL RPT , RPT OFF
—
Random play Press repeatedly.
GROUP RND , ALL RND , RND OFF
—
Operations and display indications may differ according to their availability on the
connected device.
JS_JVC_KD_SR81BT_J_EN_1=F.indd 16JS_JVC_KD_SR81BT_J_EN_1=F.indd 16 1/12/2015 8:34:11 AM1/12/2015 8:34:11 AM

ENGLISH 17
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
EASY EQ 1 USER1 / USER2 :Select a preset name.
2 Adjust your own sound settings.
SUB.W SP
*1*2
: 00 to +06 (Default: 03
SUB.W
*1*3
: –08 to +08 00
BASS  LVL : –06 to +06 00
MID  LVL: –06 to +06 00
TRE  LVL : –06 to +06 00 )
PRO EQ 1 USER1 / USER2 :Select a preset name.
2 BASS / MIDDLE / TREBLE :Select a sound tone.
3 Adjust the sound elements of the selected sound tone.
BASS Frequency: 60 / 80 / 100 / 200 HZ
(
Default: 80 HZ
Level: –06 to +06 00
Q: Q1.0 / Q1.25 / Q1.5 / Q2.0 Q1.0 )
MIDDLE Frequency: 0.5 / 1.0 / 1.5 / 2.5 KHZ (Default: 1.0 KHZ
Level: –06 to +06 00
Q: Q0.75 / Q1.0 / Q1.25 Q1.25 )
TREBLE Frequency: 10.0 / 12.5 / 15.0 / 17.5 KHZ (Default: 10.0 KHZ
Level: –06 to +06 00
Q: Q FIX Q FIX )
*1
Displayed only when [ SUB.W ] is set to [ ON ]. (  18 )
*2
Displayed only when [ SPK/PRE  OUT ] is set to [ SUB.W/SUB.W ]. (  18 )
*3
Displayed only when [ SPK/PRE  OUT ] is set to [ REAR/SUB.W ] or [ SUB.W/SUB.W ].
(
18 )
To On the faceplate
Select a preset
equalizer
Press repeatedly.
Press , then turn the volume knob within
2seconds.
Preset equalizer : FLAT (default), HARD ROCK , JAZZ , POP , R&B ,
TALK , USER1 , USER2 , VOCAL BOOST , BASS BOOST , CLASSICAL ,
DANCE
Store your own
sound settings
1 Press and hold .
2 Turn the volume knob to select [ EASY EQ ], then
press the knob.
3 Turn the volume knob to select [ USER1 ] or [ USER2 ],
then press the knob.
4 Turn the volume knob to make a selection, then
press the knob.
For settings, refer to step 2of [
EASY EQ ].
• To return to the previous setting item, press .
• To exit, press .
Other settings
1 Press and hold .
2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Repeat step 2until the desired item is selected/activated or follow the
instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press .
Default:
XX
EQ SETTING
EQ PRESET FLAT
/ HARD ROCK / JAZZ / POP / R&B / TALK / USER1 / USER2 /
VOCAL BOOST / BASS BOOST / CLASSICAL / DANCE :Selects a preset equalizer.
JS_JVC_KD_SR81BT_J_EN_1=F.indd 17JS_JVC_KD_SR81BT_J_EN_1=F.indd 17 1/12/2015 8:34:13 AM1/12/2015 8:34:13 AM

18
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO
BASS BOOST +01
/ +02 : Selects your preferred bass boost level.; OFF :Cancels.
LOUD 01 / 02 :Boosts low or high frequencies to produce a well-balanced
sound at low volume.;
OFF :Cancels.
SUB.W LEVEL
*4
SPK-OUT
*5
00 to +06 ( +03 ):Adjusts the output level of the
subwoofer connected via speaker lead. (
 27 )
PRE-OUT
*6
–08 to +08 ( 00 ):Adjusts the output level of the
subwoofer connected to the lineout terminals (SW or
REAR/SW) through an external amplifier. (
 27 )
SUB.W
*6
ON / OFF : Turns on or off the subwoofer output.
SUB.W  LPF
*4
THROUGH :All signals are sent to the subwoofer. ; LOW  55HZ /
MID  85HZ / HIGH 120HZ :Audio signals with frequencies lower than
55Hz/ 85Hz/ 120Hz are sent to the subwoofer.
SUB.W PHASE
*4
REVERSE (180°)/ NORMAL (0°):Selects the phase of the subwoofer
output to be in line with the speaker output for optimum performance.
(Selectable only if a setting other than [
THROUGH ] is selected for
[
SUB.W  LPF ].)
FADER R06 — F06 ( 00 ):Adjusts the front and rear speaker output balance.
BALANCE
*7
L06 — R06 ( 00 ):Adjusts the left and right speaker output balance.
VOL  ADJUST –05 — +05 ( 00 ):Presets the volume adjustment level of each source
(compared to the FM volume level). Before adjustment, select the source
you want to adjust. (“VOLADJFIX” appears if FM is selected.)
AMP  GAIN LOW  POWER :Limits the maximum volume level to 30. (Select if the
maximum power of each speaker is less than 50W to prevent damaging
the speakers.);
HIGH POWER :The maximum volume level is 50.
D.T.EXP
(Digital Track
Expander)
ON :Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost in
audio data compression.;
OFF :Cancels.
SPK/PRE  OUT Selects the appropriate setting to get the desired output.
*4
Displayed only when [ SUB.W ] is set to [ ON ].
*5
Displayed only when [ SPK/PRE  OUT ] is set to [ SUB.W/SUB.W ].
*6
Displayed only when [ SPK/PRE  OUT ] is set to [ REAR/SUB.W ] or [ SUB.W/SUB.W ].
*7
This adjustment will not affect the subwoofer output.
SPK/PRE OUT
Connection via lineout terminals (  27 )
Setting Lineout terminal
FRONT REAR/SW
REAR/REAR Front speakers output Rear speakers output
REAR/SUB.W Front speakers output Subwoofer output
SUB.W/SUB.W Front speakers output Subwoofer output
Connection via speaker leads (  27 )
Setting Rear speaker lead
L (left) R (right)
REAR/REAR Rear speakers output Rear speakers output
REAR/SUB.W Rear speakers output Rear speakers output
SUB.W/SUB.W Subwoofer output (Mute)
If [ SUB.W/SUB.W ] is selected:
– [
HIGH 120HZ ] is selected in [ SUB.W  LPF ] and [ THROUGH ] is not available.
– [
R01 ] is selected in [ FADER ] and selectable range is [ R06 ]to [ 00 ]
AUDIO SETTINGS
JS_JVC_KD_SR81BT_J_EN_1=F.indd 18JS_JVC_KD_SR81BT_J_EN_1=F.indd 18 1/12/2015 8:34:13 AM1/12/2015 8:34:13 AM