JVC KY-F70U - Sxga Imaging Camera Less Lens User manual

Digital Camera
Model KY-F70 INSTRUCTIONS
Illustration with optional lens attachment.
This instruction book is made from 100%
recycled paper.
SC96847-001
KY-F70
CAMERADIGITAL
C-MOUNT
For Customer Use:
Enter below the Serial No.which is
located on the unit. Retain this
information for future reference.
Model No. KY-F70
Serial No.
Introduction
Before recording
Settings and
adjustments
for recording
Basic operations
Various
recording
methods
Menu screen
settings
Connecting
to a PC
Others

E2
@@@@@@
Thank you for purchasing the JVC KY-F70
Digital Camera.
The instructions are given in three languages:
English from page 2 to 35
German from page 36 to 69
French from page 70 to 103
Bedienungsanleitung in drei Sprachen:
Englisch: Seite 2 bis 35
Deutsch: Seite 36 bis 69
Franzosisch: Seite 70 bis 103
Les explications techniques sont données:
Anglais, pages 2 to 35
Allemand, pages 36 to 69
Français, pages 70 to 103
SAFETY PRECAUTIONS
FOR USA AND CANADA
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulat-
ed“dangerous voltage”within the product’s
enclosure that may be of sufficient magni-
tude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and main-
tenance (servicing) instructions in the lit-
erature accompanying the appliance.
CAUTION: TOREDUCETHERISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICINGTO QUALIFIED SERVICE
PERSONNEL.
Information for USA
This device complies with Part 15 of the FCC Rules.
Changes or modifications not approved by JVC could
void the user’s authority to operate the equipment.
INFORMATION (FOR CANADA)
RENSEIGNEMENT (POUR CANADA)
• This Class B digital apparatus complies with Canadian
ICES-003.
• Cet appareil numérique de la classe B est conforme
à la norme NMB-003 du Canada.
Changes or modifications not approved by JVC could
void the user’s authority to operate the equipment.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELEC-
TRIC SHOCK, DO NOT EXPOSETHIS APPLI-
ANCETO RAIN OR MOISTURE.
This unit should be used with 12V DC only.
CAUTION:
To prevent electric shocks and fire hazards, do NOT
use any other power source.
Due to design modifications, data given in this in-
struction book are subject to possible change with-
out prior notice.
CAUTION:
To prevent electric shock, do not open the cabinet. No
user serviceable parts inside. Refer servicing to quali-
fied service personnel.
This unit is designed for professional use only.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION

E3
WARNING ON LITHIUM BATTERY
The battery used in this device may present a
fire or chemical burn hazard if mistreated.Do not
recharge, disassemble, heat avobe 100°C or
incinerate.
Replace battery with Panasonic (Matsushita
Electric).
CR2032, use of another battery may present a
risk of fire or explosion.
• Dispose of used battery promptly.
• Keep away from children.
•
Do not disassemble and do not dispose of in fire.
For Sweden
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent typ
som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.
For Norway
ADVARSEL
Lithiumbatteri – Eksplosjonsfare.
Ved utskifting benyttes kun batteri som anbefalt
av apparatfabrikanten.
Brukt batteri returneres apparatieverandøren.
For Denmark
ADVARSELI
Lithiumbatteri – Eksplosionsfare ved fejlagtig
håndtering.
Udskiftning må kun ske med batteri af samme
fabrikat og type.
Lever det brugte batteri tilbage til leverandøren.
For Finland
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti
asennettu.
Vaihda paristo ainoastaan laltevalmistajan
suoaittelemaan tyyppiin. Hävitä käytetty paristo
valmistajan ohjeiden mukaisesti.

E4
@@@@@@
Table of Contents
1. Introduction
Features ...........................................................................................................................6
Accessories and attachments ..........................................................................................6
Cautionary notes for the correct usage of this product ....................................................7
Part names and their functions ........................................................................................8
Explanation of terminals.................................................................................................12
2. Before recording
Basic system 1 ...............................................................................................................14
Basic system 2 ...............................................................................................................15
Inserting the lithium battery............................................................................................16
Mounting the lens...........................................................................................................17
Connecting the power ....................................................................................................18
Connecting a monitor .....................................................................................................19
Connecting an MO drive unit..........................................................................................20
Connecting a printer.......................................................................................................21
Mounting the camera .....................................................................................................22
Fall prevention ................................................................................................................23
3. Settings and adjustments for recording
Setting the dip switches (Monitor, SCSI ID) ...................................................................24
Menu settings (VGA model, Lens) .................................................................................25
Time and date settings...................................................................................................26
Monitor adjustment.........................................................................................................28
Focus adjustment...........................................................................................................29
White balance adjustment..............................................................................................30
White shading adjustment..............................................................................................32
4. Basic operations
Recording images to the main unit memory ..................................................................34
Playing back images from the memory ..........................................................................35
Saving images from the memory to an MO disk ............................................................36
Outputting images from the memory to a printer ...........................................................37
Clearing images from the memory.................................................................................38

E5
5.Various recording methods
Recording a PC monitor.................................................................................................40
Outputting negative images ...........................................................................................41
Synchronizing flash and FREEZE..................................................................................42
About ALC and EEI operations ......................................................................................43
6. Menu screen settings
Menu screen flow ...........................................................................................................44
Setting procedure...........................................................................................................46
EXPOSURE screen .......................................................................................................48
WHITE BALANCE screen ..............................................................................................51
FREEZE screen .............................................................................................................53
PROCESS screen..........................................................................................................53
SYSTEM SETTING screen ............................................................................................57
Menu screen of the PLAY mode.....................................................................................59
REC mode quick menu screen ......................................................................................60
Resetting settings...........................................................................................................62
7. Connecting to a PC
Compatible systems 1....................................................................................................64
Compatible systems 2....................................................................................................65
8. Others
Specifications .................................................................................................................66
CAUTION Cautionary notes concerning operation of the unit
MEMO Reference such as restrictions of features, etc.
ZReference page or item
Characters and symbols used in this instruction book

E6
@@@@@@
Features
●This digital camera uses three 1.45 million pixel 1/2 inch IT CDD.
●Newly developed 1/2 inch C mount Dichroic prism for the color separation prism.
●Capable of recording semi-animation (7.5 frames per second) and still images at resolution of
1360 ×1024 pixels.
●Image capturing capability using a capture board since video signals are processed in real-
time by the built-in DSP and outputted as RGN analog signals of 7.5 frames/sec.
●Monitor output can be scan-converted to 640 ×480 pixels for output to a VGA monitor.
●30 frame/sec.output capability to even a VGA real-time monitor (Draft mode).
●Output digital still images to an MO drive or recommended printer using SCSI connection.
●Export digital still images to a PC using SCSI connection.
●Remotely control your PC using RS-232C connection.
Accessories and attachments
Battery
For time and date backup
( Zpage 16)
Power cable (2 m)
For connecting with AC
adapter 8-pin cable
( Zpage 18)
Remote plug (10-pin)
REMOTE terminal plug
( Zpage 12)
Ferrite core
For power cable
( Zpage 18)
C
R
2
0
2
5
Mini screwdriver
For replacing battery
( Zpage 16)
1. Introduction
PC software (2 types)
• Remote control software
(For controlling the main unit
with a PC)
• SCSI import plug-in software
(For importing still images to
a PC)
For details, see the instructions
attached with the software.
( Zpage 64)
Warranty card
Instruction book
Wire clamp (5 units)
For clamping rear cables, etc.

E7
Cautionary notes for the correct usage of this product
• Before recording an important event, etc., always check to make sure that this product is
working properly.
• We are not liable for any missed recordings caused by malfunction of this unit, etc.
mPhenomena unique to CCD
• Smearing and blooming
When using CCD to record a bright light source, a smearing effect may occur running a
white line parallel to the light source.In addition, a blooming effect may also occur when the
light source is extremely bright, spreading light to the source surroundings.
• Line distortion
Line and patterns may appear distorted when recorded.
• White dots
White dots may appear on the screen when operating under high temperatures. Always
use the product under recommended ambient temperatures.
mCautionary notes
• Influence of strong electric waves and magnets
Screen noise and discoloration may occur when using the product near antennas of radios
and televisions or near transformers, monitors, etc.with strong magnetic force.
• Compatible lenses (Z page 17)
Although the lens mount of this product is a type C mount, take caution as there are restric-
tions on the lenses that can be used.
This product is not equipped with a back-focus adjustment feature. Please use a lens
equipped with the back-focus adjustment feature.
• Caring of the product (always turn off the power before cleaning)
Wipe the product with a soft cloth.
Do not use paint thinner or benzine as it may melt or discolor the surface.
For stubborn dirt, wipe with a cloth dampened with water-diluted neutral detergent, then
dry wipe.
mThis product is aType II information processing device (information processing device for use
in residential areas or nearby areas) conforms to the VCCI (Voluntary Control Council for
Interference by Information Technology Equipment) standards for the purpose of preventing
electrical interference in residential areas.
However, using the product near televisions and radios may cause interference of reception.
Please read the instructions carefully for the correct usage.

E8
@@@@@@
Part names and their functions
1. Introduction (continued)
^Lens mount
Although the lens mount conforms to the
type C mount lens, there are restrictions
on the lenses that can be used.
Mounting the lens ( Z page 17)
_Camera mounting bracket
Although the mounting bracket is mounted
on the bottom of the camera when shipped,
the bracket can also be mounted on the
top of the camera.
Mounting the camera ( Z page 22)
`Locking screws for the camera
mounting bracket
(M2.6 ×6mm, 3 units)
CAUTION
Always use the attached screws.Using screws
that exceed 6mm may result in malfunction of
the unit.
aScrew holes for mounting the
camera (1/4-inch)
Used when mounting the camera to a fixer
or rotating platform.
bLithium battery case
Used to case the lithium battery for time
and date backup.The lithium battery is not
installed when shipped.
Please install the attached lithium battery
(CR2032) before use.
Inserting the lithium battery ( Z page 16)
KY-F70
CAMERADIGITAL
C-MOUNT
[Front and bottom]

E9
cMENU button
Press this button to output the menu screen
from the MONITOR terminal.
Press the button once more to clear the
menu screen.
Setting in the menu screen ( Z page 44)
dSEND/UP button
●Press this button to output the same still
image* that is being outputted to the
MONITOR terminal to an MO drive or
printer.
Save images in memory to an MO disk ( Z
page 36)
Output images in memory to a printer ( Z
page 37)
* A still image refers to an image recorded
by pressing the FREEZE button while in
the REC mode or an image being played
back in the PLAY mode.
[Rear]
SEE INSTRUCTION MANUAL
POWER
DC IN
REMOTE
MONITOR
LENS
FREEZE
PLAY
SETDOWN
AW/SELSEND
SCSI
UPMENU
MODE REC
ON 1 2 3 4
●While the menu screen is being dis-
played, press this button selected item
up.
While an item is selected, use this but-
ton to change the set value.
Setting in the menu screen ( Z page 44)
eAW/SEL/DOWN button
●[AW (Auto White)]
Press this button to adjust the white bal-
ance when the light source of the sub-
ject is changed.
White balance adjustment ( Z page 28)
●[SEL (Select)]
Pressing this button each time while in
the PLAY mode will switch to the previ-
ous image in memory.
* The PLAY mode refers to the condition
which the unit is playing back recorded
images from the memory.
Playing back images from memory ( Z
page 33)
●[DOWN]
While the menu screen is being dis-
played, press this button selected item
down.
While an item is selected, use this but-
ton to change the set value.
Setting in the menu screen ( Z page 44)

E10
@@@@@@
Part names and their functions (continued)
1. Introduction (continued)
fMODE/SET button
●[MODE]
Pressing this button each time will switch
between the REC (record)* and PLAY
(playback) modes. The default mode
when the power is turned on is REC.
* REC mode is the condition which the unit
has either captured an image or is ready
towrite an image to the main unit memory.
Recording images to the main unit memory
(Z page 34)
Playing back images from the memory
(Z page 35)
●[SET]
While the menu screen is being displayed,
use this button to select a submenu or
confirm a selected item or set value.
Setting in the menu screen ( Z page 44)
[Rear (continued)]
SEE INSTRUCTION MANUAL
POWER
DC IN
REMOTE
MONITOR
LENS
FREEZE
PLAY
SETDOWN
AW/SELSEND
SCSI
UPMENU
MODE REC
ON 1 2 3 4
Ventilation hole
gREC display lamp
This lamp lights when in the REC* mode.
During FREEZE, thisdisplaylampwill flash.
* During the REC mode, camera images
are outputted to the MONITOR terminal.
Pressing the FREEZE button at this time
will save the image to the main unit
memory.
hPLAY display lamp
This lamp lights when in the PLAY* mode.
* During the PLAY mode, images saved in
the main unit memory are played back
by outputting to the MONITOR terminal.
Playing back images from the memory ( Z
page 35)

E11
iFREEZE button
While in the REC mode, press this button
to capture a still image (freeze) of the im-
ages being outputted through the MONI-
TOR terminal. At the same time, the still
image is saved to the main unit memory.
Pressing this button once more will cancel
the still image and return to the camera
images.
Saving images to the main unit memory
(Z page 34)
MEMO
You can also set the unit to automatically can-
cel the still image after 5 seconds.
FREEZE screen, CANCEL screen ( Z page 53)
jMONITOR output terminal
(D-sub 15-pin, female)
Used to connect to aVGA monitor or SXGA
compatible capture board.
The default setting is set to VGA monitor
compatible.To change the setting fromVGA
mode to SXGA mode, change the dip
switch settings.
Setting the monitor ( Z page 24)
●When in the SXGA mode, images of
1360 ×1024 pixles (7.5 frames/sec.) are
outputted.
●For the VGA mode, you can select be-
tween the FINE mode of 640 ×480 pix-
els (7.5 frames/sec.) or DRAFT mode of
640 ×240 pixels (30 frames/sec.) in the
menu screen.
Setting the VGA mode ( Z page 25)
kLENS connection terminal
Used to connect the lens cable.
Mounting the lens ( Z page 17)
lPOWER display lamp
This lamp lights when the power of the main
unit is on.
mDC IN power input terminal
(Mini DIN 8-pin, female)
Main unit power supply (DC 12V) is sup-
plied through this terminal.
For the power supply, use the AA-P700 AC
adapter.
Connecting the power ( Z page 18)
nREMOTE terminal
(Metal 10-pin, female)
Used to connect external devices such as
a freeze switch or flash unit.
5.Various recording methods ( Z page 40)
oDip switches
Used to set the SCSI ID ( Z page 24) and
monitor ( Z page 24), and output color bar
(Z page 28).
pSCSI terminal
(Half-pitch 50-pin ×2)
Used to directly output to an MO drive ( Z
page 20) or printer ( Z page 21).
The default setting of the SCSI ID is 7.
Change the SCSI ID setting when connect-
ing to a PC, etc.
Connecting to a PC ( Z page 64)

E12
@@@@@@
1. Introduction (continued)
Power terminal (Mini DIN 8-pin, female)
Explanation of terminals
14
3
6
7
8
5
2
Pin no. Signal name
1NC
2 GND
3NC
4NC
5 GND
6 12V
7NC
8 12V
Remoter terminal (Metal 10-pin, female)
Pin no. Signal name
1 A.WHITE active Zi=22k Ω
2 FREEZE L active Zi=100k Ω
3 WEN L active Zo=100 Ω3V(p-p)
4 FLASH
5 SEND (PRINT)
6 RS-SDI
7 RS-SDO
8 GND
9 12V
10 OPERATION
Lens terminal (Metal 12-pin, female)
12
8
7
10
63
4
5
9
Pin no. Signal name
1NC
2
3 GND
4NC
5 IRIS CONTROL
6 12V DC
7 IRIS POSITION
8 IRIS AUTO /MANU
9NC
10 NC
11 NC
12 NC
6
7
82
1
9
3
4
12 5
10
11
Terminal
name
FREEZE
WEN
FLASH
Conditions
• Contact point
recommended
• Rated voltage:
5.3V
• H level: 3.5 ~ 5.0V
• L level: 0 ~ 0.8V
• CMOS (5V): OK
• TLL not possible
• Output only when
in the SXGA mode
• Rated current:
150mA
• Rated voltage:
12V
I/O
IN
• 5V CMOS
• Schmidt Trigger
• Pull-up to 5V at
100k Ω
• Input capacity
0.1 µF
OUT
• 3.3V (p-p)
negative polarity
OUT
• Open collector

E13
Monitor terminal (D-sub 15-pin, female)
Pin no. Signal name
1 R OUT 700mV, 75 Ω
2 G OUT 700mV, 75 Ω
3 B OUT 700mV, 75 Ω
4 GND
5NC
6 R GND
7 G GND
8 B GND
9NC
10 GND
11 GND
12 NC
13 Hs (3V(p-p) negative polarity
Zo=100 Ω)
14 Vs (3V(p-p) negative polarity
Zo=100 Ω)
15 NC
SCSI terminal (Half-pitch 50-pin, female)
Pin no. Signal name
1 ~ 11 GND
12 GND
13 NC
14 GND
15 ~ 25 GND
26 DB 0
27 DB 1
28 DB 2
29 DB 3
30 DB 4
31 DB 5
32 DB 6
33 DB 7
34 DBP
35 GND
36 GND
37 GND
38 VC +5 (input only)
39 GND
40 GND
41 ATN
42 GND
43 BSY
44 ACK
45 RST
46 MSG
47 SEL
48 CD
49 REQ
50 I/O
15
10 6
11
15
1
2650
25

E14
@@@@@@
2. Before recording
Basic system 1
While checking the images from the camera on the monitor, output the images to an MO disk or
printer.
For the power supply, always use the AA-P700 AC adapter.
AC ADAPTER AA-P700
ON
OFF
POWER
POWER
ALARM SHEET PAPER DATA
OPEN
CP700DSA MITSUBISHI
ONLINECOPY& CUTPAPER FEED
]
AA-P700
AC
MONITOR VIDEO IN
SCSI
DC IN
KY-F70
CAMERADIGITAL
C-MOUNT
Connect to the
power supply
( Zpage 18)
AC adapter
Mount the lens
( Zpage 17)
Connect the monitor
( Zpage 19)
VGA monitor
Connect the MO drive
unit ( Zpage 20)
MO disk drive
Connect the printer
( Zpage 21)
Printer
(recommended: Mitsubishi CP700DSA)

E15
Basic system 2
This is a system to record with this camera using a flash timed by an external freeze switch.
AC ADAPTER AA-P700
ON
OFF
POWER
POWER
ALARM SHEET PAPER DATA
OPEN
CP700DSA MITSUBISHI
ONLINECOPY& CUTPAPER FEED
]
,

AA-P700
AC
KY-F70
CAMERADIGITAL
C-MOUNT
MONITOR
SCSI
REMOTE
REMOTE
DC IN
AC adapter
Microscope
adapter
Flash
Freeze switch
VGA monitor
MO disk drive
Printer
Model name
CAUTION
Use a 1/2 inch mount microscope adapter.
To avoid damage to the unit, always use an adapter that is 4mm or less from
the lens mount side. Lens
4mm or less

E16
@@@@@@
Inserting the lithium battery
2. Before recording (continued)
The lithium battery is used to back up the time and date data.
Install the lithium battery before using the unit.
<Install >
MEMO
The time and date will not be displayed correctly when the battery is not installed.When replacing the
lithium battery, reset the time and date.
Setting the time and date ( Z page 26)
Remove the screws (2 units) using the attached mini screw-
driver, then open the cover.
Completely insert the lithium battery in the direction of the ar-
row with the + side facing up.
Make sure that the battery is securely in position by the hold-
ers as shown in the diagram.
(To remove the battery, follow the procedure in reverse.)
C
R
2
0
2
5
C
R
2
0
2
5
KY-F70
CAMERADIGITAL
C-MOUNT
Screws
Battery compartment
Holders
1.
2.
3.
4.
Replace the cover and retighten the screws.
Mini screwdriver (attached)

E17
Mounting the lens
Follow the procedure shown below when mounting an auto-iris lens.For further details, see the
instruction manual of the lens.
1. Remove the lens mount cap. At this time, take caution so that dust do not enter inside the
mount.
2. To mount the lens, lightly press the thread section of the lens mount onto the thread section
of the main unit, then turn the mount clamp ring slowly clockwise until it is securely tight-
ened.
MEMO
To change the position of the lens rotation:
~First, turn the mount clamp ring counterclockwise (1/4 turns) with the lens facing you.
ÄSlowly turn the lens and after adjusting the position, retighten the mount clamp ring.
3. Insert the camera cable of the lens into the lens connection terminal on the rear of the main
unit, then securely fasten.
The iris control is made automatically from the camera.
* When using a manual iris lens, set the IRIS MODE to MANUAL (see Z page 48).
4. When using the lens remote control, connect the lens control cable (female) to the remote
control.
CAUTION
Lens is not included with this unit.
To avoid damaging the main unit, make sure that the lens mount of the lens to be
used is 4mm or less.
2.
3.
KY-F70
CAMERADIGITAL
C-MOUNT
Camera head
Thread section
Mount clamp ring
Lens
Male
Female
Lens remote control
Lens
4mm or less

E18
@@@@@@
Connecting the power
2. Before recording (continued)
Connect the DC IN terminal on the rear of the main unit and theTO CAMERA terminal of the AC
adapter (AA-P700) with the attached power supply cable (2m).
Before connecting, make sure that the power switch of the AA-P700 is set to OFF. Connecting
with the power turned on may result in malfunction.
VIDEO OUTPUT
TO CAMERAS(Y/C) OUTPUT
DC 12V=OUTPUT
EITHER
OUTPUT
MAX 1.25A
SEE INST-
RUCTION
MANUAL
AC 100V
AA-P700
AC
SEE INSTRUCTION MANUAL
POWER
DC IN
REMOTE
MONITOR
LENS
FREEZE
PLAY
SETDOWN
AW/SELSEND
SCSI
UPMENU
MODE REC
ON 1 2 3 4
After inserting the plug completely, securely fasten by
turning the ring.
To reduce emission of unwanted electrical waves, mount
the attached ferrite core as shown in the diagram on
the left.
Mount the ferrite core as close to the main unit as pos-
sible as shown in the diagram.
Connect the plug to the AC adapter side in the same
manner.
DC IN
POWER
DC IN
POWER
DC IN
POWER
AC adapter
Attached power supply cable
Clamp filter
Plug Ring

E19
Connecting a monitor
Connect the PC monitor (VGA) to the MONITOR terminal on the rear of the main unit.
●Before connecting, make sure that the power of all systems are turned off.Connecting with the
power turned on may result in malfunction.
●For the connector, commercially available VGA video cable is recommended.
●For the pin assignment, see page 13 Explanation of terminals
SEE INSTRUCTION MANUAL
POWER
DC IN
REMOTE
MONITOR
LENS
FREEZE
PLAY
SETDOWN
AW/SELSEND
SCSI
UPMENU
MODE REC
ON 1 2 3 4
MONITOR terminal

E20
@@@@@@
Connecting an MO drive unit
2. Before recording (continued)
It is possible to output image data stored in the main unit memory to an MO drive unit.( Z Page
36 Saving images from the memory to an MO disk)
To directly connect the MO drive to the main unit, set the dip switches on the rear of the main unit
as shown below.
MEMO
• The image data outputted to an MO drive will be 1360 ×1024 pixels, regardless whether the monitor
in use is VGA or SXGA, or whether the VGA mode is set to FINE or DRAFT.
• The maximum allowed length of the SCSI cable is 3m.
• When connecting an MO drive to a PC, separate setting of the SCSI ID is required.
( Z Page 64 7.Connecting to a PC)
• It is not possible to simultaneously output the image data to a printer and MO drive.
SEE INSTRUCTION MANUAL
POWER
DC IN
REMOTE
MONITOR
LENS
FREEZE
PLAY
SETDOWN
AW/SELSEND
SCSI
UPMENU
MODE REC
ON 1 2 3 4
ON 1 2 3 4
(SCSI : 7) Do not set the ID of the MO drive side to other than
7.
Dip switches
SCSI terminal