K-array K-FOOT3 User manual
USER GUIDE
•20230823•
Applies to Kobra-KK, Python-KP, Kayman-KY line array loudspeakers
Accessories Assembly
For Column Speakers
150mm
5,91in
58mm
2,28in
35mm
1,38in
K-BASE3
K-KBASEFL K-KBASEFT K-KBASESTK K-KJUNCT1
K-BASE3
K-KBASEFL K-KBASEFT K-KBASESTK K-KJUNCT1
K-BASE3
K-KBASEFL K-KBASEFT K-KBASESTK K-KJUNCT1
K-BASE3
K-KBASEFL K-KBASEFT K-KBASESTK K-KJUNCT1
K-BASE3
K-KBASEFL K-KBASEFT K-KBASESTK K-KJUNCT1
2
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
•
• Do not use this apparatus near water.
•
•
manufacturer’s instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or
•
plug has two blades with one wider than the other. A grounding plug has two
•
• Protect the power cord from being walked on or pinched particularly at the plugs,
•
products, as this may damage the products cosmetic surfaces.
•
from tip-over.
•
long periods of time.
• Avoid placing the product in a location under direct sunlight or near any appliance
•
apparatus has been damaged in any way, such as power-supply cord or plug is
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
•
•
General heed and warnings
about the product’s use and maintenance.
triangle is intended to alert the user to the presence of uninsulated,
dangerous voltage within the product enclosure that may be of
magnitude to constitute a risk of electrical shock.
the user to the presence of important operating and maintenance
operating instructions and indicates that the operating instructions
should be considered when operating the device or control close to
where the symbol is placed.
Please dispose of this product at the end of its operational lifetime by
bringing it to your local collection point or recycling center for such
Directive.
WARNING
Failure to follow these safety instructions could
the device or other property.
This apparatus is intended for professional use.
3
•
minimum.
•
• Key rigging components must be inspected before each use.
• Any rigging components found to be defective, or even suspect might be
• Always use properly rated rigging hardware.
•
manufactured by K-array.
• K-array loudspeaker and hardware are intended for suspension from approved
of the suspension points.
•
and experienced professionals.
•
loudspeaker systems conform to all applicable laws and regulations in force at
the time and location.
•
•
system to ground in order to avoid any damage or failure due to any unintended
hits, gust of wind, vibrations or such.
• K-array cannot be held responsible for damage caused by improper use of the
loudspeakers.
•
limits are designed to provide reasonable protection against harmful
instructions, may cause harmful interference to radio communications. However,
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
2.
3.
the receiver is connected.
4.
All trademarks are the property of their respective owners.
4
Index
6
6
6
8
8
9
10
|
14
15
16
|
16
18
18
18
19
Accessories For Column Speakers
User Guide
manuals and safety instruction before using the products.
After reading this manual, be sure to keep it for future reference.
device please contact K-array customer service at
support@k-array.com or contact the
in your country.
column loudspeakers.
Kayman-KY line array loudspeakers:
•
•
•
•
•
•
•
line array loudspeaker only:
•
•
•
•
Accessories For Column Speakers
User Guide
6
Unpacking
thoroughly inspected before leaving the factory.
notify the shipping company.
the column speaker.
Assembly the hinges to both ends of the column
speaker.
1
1
3
2
A
1
B
2
2
3
4
4 mm hex key
1
2
3
4
4 mm hex key
Accessories For Column Speakers
User Guide
7
and insert the pins to block the assembly.
the system directivity:
A.
3
4a
4b
4c
Accessories For Column Speakers
User Guide
8
mount the terminal backward
1
1
2
2
3
3
4
4
4 mm hex key
4 mm hex key
A 1
B
Accessories For Column Speakers
User Guide
9
install the bracket.
loudspeaker. You can optionally keep the plate in place.
Assembly the bracket to the loudspeaker.
122mm
4,80in
4 mm hex key
4 mm hex key
4 mm hex key
A
C
B D
Accessories For Column Speakers
User Guide
wall.
the blocking screws of the bracket at both the
loudspeaker side and wall side.
install the bracket with the K-shaped hole.
180mm
7,08in
4 mm hex key
E
F
1
2
Accessories For Column Speakers
User Guide
loudspeaker. You can optionally keep the plate in place.
Assembly the bracket to the loudspeaker.
3 5
4
4 mm hex key
4 mm hex key
Accessories For Column Speakers
User Guide
|
Remove the plate form back of the loudspeaker.
Pass the speaker cable using either the hole on the
Steadily secure
supporting surface.
4 mm hex key
4 mm hex key
1
3
2
Accessories For Column Speakers
User Guide
In order to align
and connect up to
steps 4 and 5.
properly and
steadily secure the
supporting surface.
5
4 mm hex key
4
Accessories For Column Speakers
User Guide
Assembly the top shield to the column loudspeaker.
Up to
aligned on top of the
6
Accessories For Column Speakers
User Guide
A
B
Accessories For Column Speakers
User Guide
line array loudspeakers.
position.
|
1
A
2
Accessories For Column Speakers
User Guide
subwoofer.
B D
C
Accessories For Column Speakers
User Guide
105mm
4,14in
59mm
2,32in
97mm
3,82in
118mm
4,64in
90mm
3,54in
105mm
4,14in
59mm
2,32in
97mm
3,82in
118mm
4,64in
90mm
3,54in
560mm
22,05in
30mm
1,18in
25mm
0,98in
150mm
5,91in
Accessories For Column Speakers
User Guide
150mm
5,91in
58mm
2,28in
35mm
1,38in
150mm
5,91in
58mm
2,28in
35mm
1,38in
Accessories For Column Speakers
User Guide
20
507mm
20,0in
486mm
19,1in
300mm
11,8in
300mm
11,8in
507mm
20,0in
45mm
1,8in
40mm
1,6in
560mm
22,0in
8mm
0,3in
300mm
11,8in
300mm
11,8in
This manual suits for next models
10
Table of contents
