Kaiser Baas X-BEAM User manual

1
x-beam
Complete User Guide
X-Beam Action Light

Join the social movement and follow us on
Disclaimers & Warnings
Included Accessories
Product Diagram
Set up your X-Beam
Recharging the Battery
Operating Guide
Modes of Use
LED Indicators
Attaching your X-Beam
Waterproof Seal Care
Specifications
Support
04
05
06
07
08
09
10
11
12
13
14
15
DISCOVER: BRILLIANCE
Share your footage with us on social media
#KBdiscover
To view the entire Kaiser Baas
product range visit:
www.kaiserbaas.com
Contents

3 4
Disclaimers & Warnings
The X-Beam Action Camera Light is a
high powered LED light that will get hot
after extended periods of use. Exercise
caution when operating the X-Beam Action
Camera Light to avoid injury.
WARNING:
DO NOT stare directly into the light source.
DO NOT use optical instruments to look
into the light source.
DO NOT point the X-Beam Action Camera
Light into people’s eyes.
DO NOT expose the X-Beam Action
Camera Light to fire or extreme heat.
DO NOT attempt to modify or disassemble
the product. This will void your warranty.
DO NOT use the X-Beam Action Camera
Light if the housing has been cracked or
damaged.
Before operating
please ensure
you have read
and understood
the safety
precautions

5 6
Included Accessories Product Diagram
Please ensure the product package
has the following contents.
X-Beam Action Camera Light
Rechargeable 2200mAh Battery
Dual Mount
Screw Bolt
On / O Mode Button
LED Mode Indicator
Short Screw
Micro USB Cable
Quick Release Mount
Spare Rubber Seal
A
A
E
B
B
F
C
D
G
H
C
G
D
H
A
E
B
F
Front Back
A B

7 8
Ensure that your X-Beam Action Camera
Light is fully charged before use.
Battery Operation
Removing the battery
1. Lift the clip on the top of the X-Beam
Action Camera Light to reveal the
battery housing. (Fig. A)
2. Slide the battery out of the housing.
(Fig. B)
1. To charge your X-Beam Action
Camera Light, connect the provided
Micro USB cable.
2. Connect the USB cable to an
electronic device with a USB port.
3. A full charging cycle will take approx.
3 hours by 1A/2.1A charger.
4. A red light indicates the battery
is charging.
5. A green light indicates the battery
is fully charged.
Set up Your X-Beam Recharging the Battery
Fig. A
Fig. B
Note: If using a wall charger, ensure
that it is a certified product for
your region. AC Input: 100-240VAC
50/60Hz. DC Output: 5VDC 1A/2.1A.
Only use a USB charger with
suitable approval and certification.
Do not charge in conditions outside
of the 10°C-45°C range.
LI-IO N
Input: 5VDC 2.1A
Rechargeable Li-ion battery
3.7VDC 2200mAh 8.14Wh
CHARGE COMPLETE
CHARGE IN PROGRESS
DISASSEMBLE OR EXPOSE THE BATTERY
TO FIRE OR WATER.RISK OF FIRE AND
BURNS. DO NOT OPEN, CRUSH , HEAT
ABOVE 60°C OR INCINERATE.FOLLOW
MANUFACTURER’S INSTRUCTIONS.
CAUTION:DO NOT SHORT CIRCUIT,
Manufacturer: GREAT POWER BATTERY(ZHUHAI)CO.,LTD.
DATE:2016-05-01
Model: BP-01
Great Power 062540
IEC: 1ICP7/26/41-4
Indicators
Charging
Charged

9 10
• Insert the battery into the light, close
the housing and snap the clip closed.
Refer to Fig. A and Fig. B
• The On / Off switch is located on the
top of the X-Beam Action Camera
Light and is used to power on the
device and to change the light modes.
• Press and hold the power button for
2 seconds to turn the X-Beam on.
• Hold the power button for 6 seconds
to turn the X-Beam off.
Operating Guide
Fig. B
Fig. A
Lighting Mode Specifications
Modes Wide Ambient Target
Lumens 1000/500 700/350 300/150
Battery 0.5/1 Hr 0.75/1.5 Hr 1.5/3.5 Hr
Cree Leds 6 Led 4 Led 2 Led
There are 3 modes of operation for the
X-Beam Action Camera Light. Each mode
has a High and Low light setting. They
cycle through in the following order:
Wide Angle High, Wide Angle Low,
Ambient High, Ambient Low,
Target High, Target Low, Off
Modes of Use
To cycle between the different modes
Whilst the light is on click the power
button. Continue to click the button to cycle
through. The light will turn off after a cycle.

11 12
1. Low Voltage Indicator - The red battery
icon will switch on when the battery
voltage reaches approximately 3.35V
2. Target Mode
3. Ambient Mode
LED Indicators Attaching Your X-Beam
4. Wide Mode
5. Overheat Indicator – This icon will
switch on when the temperature of
the light reaches approximately 55°C.
Please switch off the light and let it
cool when this light is on.
1
4 3
2
5
Attach the X-Beam Action Camera Light
to your Action Camera by using the
dual mount included. Alternatively, the
X-Beam can be attached to any Kaiser
Baas mounts or GoPro™ mounts. It pairs
perfectly with a bike mount or float grip.

13 14
To maintain your X-Beam Action Camera
Light, it is recommended that you clean
the light and waterproof seal after every
use. The waterproof seal, located on the
door, can be cleaned by gently wiping
away any dirt, dust or debris with a
clean, dry and soft cloth.
Ensure the seal is clean to maintain
the seals integrity. If the seal becomes
damaged or lost, please replace with
the included spare part. Always check
the seal for any dirt, dust or debris
prior to use.
Waterproof Seal Care PRODUCT SPECIFICATIONS
Number of LED’s 6
Type of LED’s XT-E CREE
Colour Temperature 5000K
Light Modes 3
Mode Wide Ambient Target
Lumens 1000/500 700/350 300/150
Battery 0.5/1 hr 0.75/1.5 hr 1.5/3.5 hr
LED 6 4 2
Angle 45° 70° 35°
Battery 3.7VDC 2200mAh 8.14Wh Li-Ion
Charge Time 3 Hours with 5V 2.1A USB Adaptor
Waterproof 40m IP68
Dimensions 70x77x42 mm
Weight 215g
Note: After use in salt water, rinse
the X-Beam Action Camera Light in
fresh water to prevent corrosion.

15 16
Got a question about your
Kaiser Baas X-Beam Action Light?
Live Chat:
www.kaiserbaas.com/support
Email:
[email protected]
For further information please visit:
www.kaiserbaas.com
Kaiser Baas Support

17